Siemens CL-010-I - Manuals

ADSL Router User Manual ³ RFC2684 LLC Encapsulation and VC Multiplexing over AAL5 ³ RFC2364 Point-to-Point Protocol (PPP) over AAL5 ³ RFC2225 Classical IP and ARP over ATM ³ RFC2516 PPP over Ethernet: support Relay (Transparent Forwarding and Client functions) ³ Support PPPoA or PPPoE Bridged mode (...

³ Firmware upgrades through HTTP, TFTP, or FTP ³ The boot loader contains very simple web page to allow the users to update the run-time firmware image. ³ Configuration file backup and restore ³ SNMPv1/v2 agent with MIB-II, ADSL Line MIB Unpacking Check the contents of the package against the pack c...

ADSL Router User Manual Subscription for ADSL Service To use the ADSL Router, you have to subscribe for ADSL service from your broadband service provider. According to the service type you subscribe, you will get various IP addresses: Dynamic IP: If you apply for dial-up connection, you will be give...

Chapter 1: Overview Chapter 1: Overview This chapter provides you the description for the LED and connector for front and rear view of the router. Before you use/install this router, please take a look at this information first. Physical Outlook Front Panel The following illustrations show the front...

Rear Panel The following figures illustrate the rear panel of your ADSL Router. Connector Description 9VAC 9 VAC Power connector Power switch Ethernet Ethernet RJ-45 connector DSL RJ-11 connector 9 VAC

Chapter 2:System Requirement and Installation Chapter 2: System Requirement and Installation System Requirement To access the ADSL Router via Ethernet, the host computer must meet the following requirements: ™ With Ethernet network interface. ™ Must have TCP/IP installed. ™ Set client PC with obtain...

Connecting the ADSL Router Follow the steps below to connect the related devices. n Connecting the ADSL line. Connect the DSL port of the device to your ADSL wall outlet with RJ-11 cable. o Please attach one end of the Ethernet cable with RJ-45 connector to the LAN port of your ADSL Router. p Connec...

Chapter 3: Configuration For connecting through a hub, please refer to the following diagram for an example. 9 VAC Setting TCP/IP In order to access the Internet through the router, each host on your network must install/setup TCP/IP. Please follow the steps below for select a network adapter.

For Windows 98 1. Click on the Start menu, point to Settings and click on Control Panel . 2. Double-click the Network icon 3. The Network window appears. On the Configuration tab, check out the list of installed network components. Option 1: If you have no TCP/IP protocol, click Add . Option 2: If y...

8. When returning to Network window, click OK 9. Wait for Windows copying files. 10. When prompted with System Settings Change dialog box, click Yes to restart your computer.

Chapter 3: Configuration For Windows ME 1. Click on the Start menu, point to Settings and click on Control Panel . 2. Double-click the Network icon. 3. The Network window appears. On the Configuration tab, check out the list of installed network components. Option 1: If you have no TCP/IP protocol, ...

9. Wait for Windows copying files. 10. When prompted with the System Settings Change dialog box, click Yes to restart your computer. For Windows NT 1. Click Start , point to Settings , and then click Control Panel . 2. Double-click the Network icon. 3. The Network window appears. On the Protocols ta...

9. When returning to Network window, click Close . 10. When prompted with Network Settings Change dialog box, click Yes to restart your computer.

Chapter 3: Configuration For Windows 2000 1. From the Start menu, point to Settings and then click Network and Dial-up Connections. 2. Right-click the Local Area Connection icon and then click Properties . 3. On the General tab, check out the list of installed network components. Option 1: If you ha...

Chapter 3: Configuration For Windows XP From the Start menu, point to Control Panel and then click Network and Internet Connections . Click Network Connection and then click Properties . Click Network Connection and then click Properties .3.On the General tab, check out the list of installed network...

For Windows Vista 8. Open the Start menu, point to Control Panel and click it. 9. Click Network and Internet. 10. Select Network and Sharing Center .

14. Under the General tab, enable Use the following IP address . Enter the IP address : 192.168.1.x (x is between 2 and 254), Subnet Mask : 255.255.255.0 and Default gateway : 192.168.1.1 . Then click Ok. Renewing IP Address on Client PC After the ADSL Router gets on line, there is a chance that you...

Chapter 3: Configuration For Windows XP On the IP Address tab, select Obtain an IP address automatically . Then click OK . Windows Vista On the IP Address tab, select Obtain an IP address automatically . Then click OK .

Renew IP Address on Client PC There is a chance that your PC does not renew its IP address after the ADSL Router is on line and the PC cannot access the Internet. Please follow the procedures below to renew PC’s IP address. For Windows 98ME 1. Select Run from the Start menu. 2. Type winipcfg in the ...

For Windows 2000 1. From the Start menu, point to Programs , Accessories and then click Command Prompt . 2. Type ipconfig at prompt. Then you will see the IP information from DHCP server. 3. If you want to get a new IP address, type ipconfig /release to release the previous IP address and then type ...

Chapter 3:Connecting and Accessing Internet Chapter 3: Connecting and Accessing Internet This chapter is to help you accessing into Internet with a quick and convenient way. If you need more detailed information for web configuration, please get into the next chapter for the advanced configuration. ...

PPP over ATM (PPPoA) Mode R D A I U S S e r v e r A A A B R A S S T M - 1 D S L A M L o o p D y n a m i c P u b l i c I Pa s s i g n e d b y B R A S P P P o A + N A T + D H C P o n P r i v a t e L A N H u b A D S L R o u t e r E t h e r n e t P C ( S ) 1 9 2. 1 6 8 . 1. 3 1 9 2 .1 6 8 . 1 . 2 P P P ...

Chapter 3:Accessing Internet PPP over ATM (PPPoA) IP Extension Mode R D A I U S S e r v e r A A A B R A S S T M - 1 D S L A M L o o p P P P o A + N A T + D H C Po n P r i v a t e L A N H u b A D S LR o u t e r E t h e r n e t P C P P P o v e r A T M D e f a u l t P r i v a t e I P 1 9 2. 1 6 8 . 1 ....

PPP over Ethernet (PPPoE) Mode R D A I U S S e r v e r A A A B R A S S T M - 1 D S L A M L o o p D y n a m i c P u b l i c I P a s s i g n e d b y B R A S P P P o E + N A T + D H C P o n P r i v a t e L A N H u b A D S L R o u t e r E t h e r n e t P C ( S ) 1 9 2 . 1 6 8 . 1 . 3 1 9 2 . 1 6 8 . 1 ....

Chapter 3:Accessing Internet PPP over Ethernet (PPPoE) IP Extension Mode R D A I U S S e r v e r A A A B R A S S T M - 1 D S L A M L o o p D y n a m i c P u b l i c I Pa s s i g n e d b y BR A S P P P o E I PE x t e n s i o n M o d e H u b A D S L R o u t e r E t h e r n e t P C ( S ) P P P o v e r ...

Numbered IP over ATM (IPoA) R D A I U S S e r v e r A A A B R A S S T M - 1 D S L A M L o o p P u b l i c I P P r e - a s s i g n e d b y I S P H u b A D S LR o u t e r P C ( S ) I P o v e r A T M S / W D e f a u l t P r i v a t e IP 1 9 2 . 1 6 8 . 1 . 1 * B R A S : B r o a d b a n d Re m o t e A c...

Chapter 3:Accessing Internet 7. Check the network information. Make sure the settings match the settings provided by ISP. Click Finish . 8. Set TCP/IP for your computer. Specify an IP Address, subnet mask and set default gateway. eg: IP Address: 10.3.75.51 Subnet Mask: 255.255.255.248 Gateway: 10.3....

Bridge Mode R D A I U S S e r v e r A A A B R A S S T M - 1 D S L A M L o o p B r i d g e M o d e H u b A D S L R o u t e r P P P o EC l i e nt S /W PC ( S ) P P P o v e r E t h e r n e t D e f a u l t P r i v a te I P 1 9 2 . 1 6 8 . 1 . 1 * B R A S : B r o a d b a n d Re m o t e A c c es s S e r v...

Chapter 5:Connection Mode Chapter 4: Web Configuration Some users might want to set specific configuration for the router such as firewall, data transmission rate… and so on. This chapter will provide you advanced information of the web pages for the router for your reference. Using Web-Based Manage...

Outline of Web Manager For configure the web page, please use admin as the username and the password. The main screen will be shown as below. Title : It indicates the title of this management interface. Main Menu : Includes Quick Start, Status, Advanced and Management. Main Window : It is the curren...

Chapter 5:Connection Mode Quick Start The pages for the Quick Start provide user a quick way to set for the router. If you do not know more about the router, you can use the Quick Start pages to adjust basic settings to make your router activating. Connect to Internet This is a quick way to connect ...

After clicking on the Next button from the VPI/VCI web page, the following screen will appear. Please choose the connection type and encapsulation mode that you want to use and click Next for next page. For example, PPP over Ethernet (PPPoE) in this screen is selected. Next, we are going to tell you...

Chapter 5:Connection Mode PPP over ATM/ PPP over Ethernet If the type you choose is PPP over ATM or PPP over Ethernet, please refer to the following information. According to the ISP’s configuration on the server, you can choose PPPoE and PPPoA modes. If the ISP provides PPPoE service, the connectio...

Chapter 5:Connection Mode PCs. Start IP Address: Type in the start point IP address. End IP Address: Type in the end point IP address. Leased Time: Type in the duration for the time. The default is 1day. DHCP Server Off: Check this item if DHCP service isn’t needed on the LAN. You can check it at th...

IP over ATM If the type you have to choose is IP over ATM, please refer to the following information. IPoA is an alternative of LAN emulation. It allows TCP/IP network to access ATM network and uses ATM quality of service’s features. Choose IPoA and click Next. None: If it is not necessary to set th...

Chapter 5:Connection Mode Bridging If the type you choose is Bridging , please refer to the following information. The bridging mode can configure your router to send packets received on any port such as ATM PVC or Ethernet with a broadcast MAC address to all other ports. Choose Bridging and click N...

Chapter 5:Connection Mode Status Overview This page is displaying the current status for the DSL connection. It includes if the lists the LAN IP address, default gateway, DNS servers IP address, firmware version, the period of activating the router, and so on. The system status will be changed accor...

ADSL Line This page shows all information for ADSL. For knowing the quality of the ADSL connection, please click ADSL BER Test button to have advanced information. Click More Information to show more detailed information about ADSL Line Status. ADSL BER Test This test determines the quality of the A...

Chapter 5:Connection Mode When the test is over, the result will be shown on the following dialog for your reference. Click Close to close this dialog. Internet Connection This page displays the connection information for your router, such as PVC name, category, protocol, invoking NAT or not, IP add...

Chapter 5:Connection Mode Advanced Setup Local Network- IP Address This page is the same as you can see in the Configure LAN side Settings page while running the Quick Setup . It allows you to set IP Address and Subnet Mask values for LAN interface. Primary IP Address: Type in the first IP address t...

DHCP Server On: Check this item if DHCP service is needed on the LAN. The router will assign IP address, gateway address for each of your PCs. Start IP Address: Type in the start point IP address. End IP Address: Type in the end point IP address. Leased Time: Type in the duration for the time. The d...

Local Network – UPnP The UPnP is available only for Windows XP. If you are not user of Windows XP, this page does not have any meaning to you. This page allows you to enable the UPnP function through the web page for your router. Internet-Connections Setting To set WAN settings for each service, ple...

Chapter 5:Connection Mode Internet - ADSL Settings Enable ADSL Port: Check this box to enable this function. It simply invokes the line mode that you choose here for the router. Select the support of line modes: There are several selections for your choosing. Select the one that you need. For Exampl...

Allow you to remove the selected static route settings. Adding a New One To add a static route, please choose Static Route - Add. Type the destination network address, subnet mask and gateway that you get from ISP and click Apply . Destination Network Address: The destination IP address of the netwo...

Chapter 5:Connection Mode … For a router with a direct connection to the Router’s local Router, the Gateway IP Address is the address of the Router’s local router. … For routers which must forward packets to another router before reaching the Router’s local router, the Gateway IP Address is the addr...

different interface. Otherwise, disable this function. Click Apply to invoke the settings set here.

Chapter 5:Connection Mode Virtual Server-Port Forwarding The Router implements NAT to let your entire local network appear as a single machine to the Internet. The typical situation is that you have local servers for different services and you want to make them publicly accessible. With NAT applied,...

IP Address seen by Internet Users Please note that, in the above picture, both Internet users are connecting to the same IP address, but using different protocols. To Internet users, all virtual servers on your LAN have the same IP Address. This IP Address is allocated by your ISP. This address shou...

Chapter 5:Connection Mode From Internet Host IP Address: Select the initial place for port forwarding. If you choose SINGLE, a box will appear for you to fill in the IP address for the specific host. And, if you choose SUBNET, the boxes of IP and Subnet will appear for you to fill in the IP address ...

Or define by yourself by typing the words into the field of User defined. Click Apply to complete the setting. Virtual Server - DMZ Host Direct Mapping Zone (DMZ) uses a technology that makes Router forwarding all incoming packet to internal specific server. To close the function of DMZ Host, please...

Chapter 5:Connection Mode Virtual Server - Dynamic DNS The Dynamic DNS (Dynamic Domain Nasme System) combines both functions of DNS and DHCP to map a dynamic IP into a fixed domain name. This page allows you to access into virtual servers with a domain name and password. Dynamic DNS ： Selects Enable...

Firewall The firewall is a software that interrupts the data between the Internet and your computer. It is the TCP/IP equivalent of a security gate at the entrance to your company. All data must pass through it, and the firewall (functions as a security guard) will allow only authorized data to be p...

A new IP filtering setting for Outbound traffic is created in the web page. To edit the setting, please click the pencil mark to get into the editing page. To delete the setting, click the trash mark to erase it. To set another IP filtering, click Add again. For adding a new Inbound IP Filtering, cl...

Chapter 5:Connection Mode is the default setting. IP type of Service : The system provides some types of service for you to choose. The meaning of each type is the same as the denotation. The default one is No change. IPQoS To classify the upstream traffic by assigning the transmission priority of t...

you want to invoke the QoS traffic rule. Destination Port: Type in the destination port for the traffic rule. The range is from 0 to 65535. Traffic Priority: There are three options – Low, Medium, and High that you can choose. It decides the order of each data transmitted through this device. IP Pre...

Chapter 5:Connection Mode Group Name: Type in a name here as a group name. It must be unique. The word length must not be over the length of the field. Available Interfaces: The available interfaces (such as Ethernet) will be displayed in the left side box. When you choose it and click Add, it will ...

Chapter 5:Connection Mode Management Diagnostics To check the link status for the network and your computer, a diagnostic test can guide you to detect the network problem. The testing items are listed and accomplished one by one. If the previous one is failed, than the items below that failed one wi...

Chapter 5:Connection Mode Admin Account This page allows you to type in the password for accessing into your DSL Router. For the Admin Account , the default setting for user password is admin . If you want to change the username and the password, please retype the new password in the Confirm field f...

Interntet Time The router’s clock must synchronize with global Internet’s time. The time you set in the screen will be adapted to system log. Update: Click this button to refresh the current time. Set Time by: The default setting is Manual. If you select Time Server, you don’t need to type in the ti...

Chapter 5:Connection Mode There are 8 types for log level and display level for your choose. The default is Debugging . The mode selection includes Local , Remote and Both . The default one is Local. If you choose Remote or Both , all the events will be sent to the specified UDP port of the specifie...

SNMP Setting The SNMP, the abbreviation of Simple Network Management Protocol, is used to refer to a collection of specifications for network management that include the protocol itself, the definition of data structures and associated concepts. A management station performs the monitoring function ...

Chapter 5:Connection Mode workstation by way of SNMP agent. Backup Config To backup your configuration for the router to your computer, you can use Backup Config web page to save the settings. And when you want to restore the settings in the future, simply open Backup Config web page and use Browse ...

UPnP for XP Universal plug and play (UPnP) is an architecture for pervasive peer to peer network connectivity of intelligent appliances and PCs of all form factors. It is designed to bring easy-to-use, flexible, standards-based connectivity to ad-hoc or unmanaged networks whether in the home, in a s...

Chapter 5:Troubleshooting Chapter 5: Troubleshooting If the suggested solutions in this section do not resolve your issue, contact your system administrator or Internet service provider. Problems with LAN PCs on the LAN cannot get IP addresses from the ADSL Router. The chances are that the interface...

Chapter 6: Troubleshooting Request time out Then the DNS is not reachable. Check your DNS setting on the ADSL Router. Problems with Upgrading The following lists the error messages that you may see during upgrading and the action to take. … Error : All the ADSL LEDs light up and cannot light off as ...

Chapter 6: Glossary Chapter 6: Glossary ARP ( Address Resolution Protocol ) ARP is a TCP/IP protocol for mapping an IP address to a physical machine address that is recognized in the local network, such as an Ethernet address. A host wishing to obtain a physical address broadcasts an ARP request ont...

Chapter 7: Glossary configured and mapped to a private workstation address when accesses are made through the gateway to a public network. For example, the ADSL Router is assigned with the public IP address of 168.111.2.1. With NAT enabled, it creates a Virtual LAN. Each PC on the Virtual LAN is ass...

the cells belonging to the same connection can be distinguished. A unique and separate VPI/VCI identifier is assigned in advance to indicate which type of cell is following, unassigned cells, physical layer OAM cells, metasignaling channel or a generic broadcast signaling channel. Your ISP should su...

Appendix A: Specifications Appendix A: Specifications Interface z One RJ-11 port for ADSL connection z Four RJ-45 ports for IEEE 802.3/802.3u 10/100 Base-T auto-sensing and auto-crossover Ethernet connection z One hidden reset button for restoring to factory default settings Regulatory Approvals and...

Appendix B: Server Setup for 802.1x Client Appendix B: Server Setup for 802.1x Client Getting Client Certificate 1. Please connect the client to a network that doesn’t require port authentictaion. 2. Open up Microsoft Explorer in Windows XP, and go to http://<yourserver>/certsrv. 3. Authentica...

Appendix C: WEEE – B2C All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. The correct disposal and separate collection of your old appliance will help preve...