Shop Fox W1814 - Manuals - manualsarea.com

Page 3 - LG

J<K LG <C< : K I @: 8 C D 8 @EK< E8E: < J<I M @:< G8I K J FG< I 8 K@FEJ J8= < K P @EKI F;L: K@FE LJ<K?<HL@:B>L@;<G8><C89<CJKFJ<8I:?FLK@E=FID8K@FE=8JK KXYc\f]:fek\ekj INTRODUCTION ...................................... 2 Woodstock Technical Support ....

Page 5 - Dfkfi

-3- N(/(+Fne\ijDXelXcD]^%('&'/" @EKI F;L: K@FE Phone #: (360) 734-3482 • Online Tech Support: [email protected] • Web: www.shopfox.biz B68=>C: HE:8>;>86I>DCH Dfkfi Type ...........................................................................................................

Page 8 - FE

-6- N(/(+Fne\ijDXelXcD]^%('&'/" J8 = < K P ('% E<M<IC<8M<N?<ED8:?@E<@JILEE@E>% Turn power F== and allow all moving parts to come to a complete stop before leaving machine unattended. ((% ;F EFK LJ< @E ;8E><IFLJ <EM@IFED<EKJ% DO NOT use machinery in damp...

Page 18 - To check the knife height, do these steps:

-16- N(/(+Fne\ijDXelXcD]^%('&'/" J< K L G JkiX`^_k\[^\ Flk]\\[ @e]\\[ =`^li\(0% Illustration of a typical cutterhead alignment setup. The knives MUST be level with the outfeed table when they are at top dead center (their highest point during rotation) or the workpiece cannot be safely fe...

Page 22 - FG

-20- N(/(+Fne\ijDXelXcD]^%('&'/" FG < I 8 K@FEJ This section covers the basic parts and controls used during routine operations. Refer to =`^li\j),Xe[)- for basic parts and control locations. 8% FE&F==Jn`kZ_1 This paddle switch starts and stops the cutterhead rotation. The yellow part...

Page 25 - JkfZb

-23- N(/(+Fne\ijDXelXcD]^%('&'/" FG< I 8 K@FEJ Jli]XZ\GcXe`e^ The purpose of surface planing on the jointer is to make one flat face on a piece of stock (see =`^li\j*+ & *, ) to prepare it for surface planing on a thickness planer. Kfjli]XZ\gcXe\fek_\af`ek\i#[fk_\j\jk\gj1 (% Read and ...

Page 32 - XYflk

-30- N(/(+Fne\ijDXelXcD]^%('&'/" J<I M @:< M$9\ckI\gcXZ\d\ek Your W1814 uses belts to drive both the cutterhead and the dust collection impeller. When these belts are not tensioned correctly, misaligned, or damaged, your jointer will not function properly. The part number for the repla...

Page 39 - READ MANUAL LABEL-HORZ

-37- N(/(+Fne\ijDXelXcD]^%('&'/" G8I K J CXY\cj&:fjd\k`ZGXikj Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, RE...

Page 41 - EZab8aj

CUT ALONG DOTTED LINE Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________ Zip ________________________ Phone...

Page 42 - Place

TAPE ALONG EDGES--PLEASE DO NOT STAPLE FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE NFF;JKF:B@EK<IE8K@FE8C@E:%G%F%9FO)*'09<CC@E>?8D#N80/)).$)*'0 Place Stamp Here