Shop Fox W1781 - Manuals - manualsarea.com

Page 3 - Safety Instructions for Pneumatic Tools; SAFETY; For Your Own Safety Read Instruction Manual; NOTICE

Model W1781 21˚ Framing Nailer -1- Safety Instructions for Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before operation. 3. KEEP WORK AREA CLEAN. ...

Page 5 - Additional Safety Instructions for Nailers

Model W1781 21˚ Framing Nailer -3- 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible gase...

Page 6 - INTRODUCTION; Woodstock Technical

Model W1781 21˚ Framing Nailer -4- No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other tools with caution and respect. Failure to do so could result in serious persona...

Page 7 - Compressed Air System

Model W1781 21˚ Framing Nailer -5- The Model W1781 is designed to be operated at 80-110 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum operating pressure for your model. Before using your new nailer, regulate the air pressure to find the optimum setting within the...

Page 8 - SETUP; Inventory

Model W1781 21˚ Framing Nailer -6- SETUP Inventory This tool has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Unpacking The following is a description of the main components shipp...

Page 9 - Safety Nose Mechanism

Model W1781 21˚ Framing Nailer -7- A safety mechanism on the nose of the nailer protects against accidental firing. When the trigger is pressed, the nailer will not fire until the safety nose mechanism is depressed. Before you use your nailer for the first time, check the safety nose mechanism to en...

Page 10 - OPERATIONS; Loading; Operating

Model W1781 21˚ Framing Nailer -8- OPERATIONS Loading When replacing nails in your Model W1781, follow these guidelines: Type: .............................. Round HeadAngle: ....................................... 21°Diameter: ............................... 0.113"Length: .........................

Page 11 - Adjusting Depth

Model W1781 21˚ Framing Nailer -9- 5. Pull the trigger. — If the nail drove into the wood far enough, continue with your intended operations. — If the nail either went too far or not far enough, then go to the Adjusting Depth section on this page. 3. Depress the safety nose mechanism against your wo...

Page 12 - Clearing Jammed Nails

Model W1781 21˚ Framing Nailer -10- A jammed nail must be cleared before using the nailer again. To clear a jammed nail from the dis-charge area, do these steps: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Pull the magazine handle all the way back until it latches. 3. Remove the nail stick from the...

Page 14 - CLEANING & LUBRICATION; Cleaning

Model W1781 21˚ Framing Nailer -12- CLEANING & LUBRICATION Cleaning Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this may resu...

Page 15 - PARTS BREAKDOWN

Model W1781 21˚ Framing Nailer -13- PARTS BREAKDOWN �� ...

Page 16 - PARTS LIST

Model W1781 21˚ Framing Nailer -14- PARTS LIST REF PART � # DESCRIPTION REF PART � # DESCRIPTION 1 X1781001 PISTON � REPAIR � KIT 50 XPSB03M CAP � SCREW � M5-.8 � X � 8 2 XPAW06M HEX � WRENCH � 6MM 51 X1781051 SAFETY � YOKE 3 XPAW05M HEX � WRENCH � 5MM 52 X1781052 COMPRESSION � SPRING 4 XPAW04M HEX ...

Page 17 - Troubleshooting; Symptom

Model W1781 21˚ Framing Nailer -15- Troubleshooting Symptom Possible Cause Cause Possible Solution Air leaking at trig- ger valve area. 1. O-rings in trigger valve housing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking between housing and hose 1....

Page 19 - Warranty Registration

CUT ALONG DOTTED LINE Name ___________________________________________________________________________________Street __________________________________________________________________________________City _________________________ State ___________________________ Zip ________________________Phone # ...