Shindaiwa DGW400DM-380A - Manuals

3. Usage z Arc Welding z Electric Tools and Home Appliances z Power Source for lights Caution : Damage to the equipment or other properties z The equipment is designed for the above purposes only. Do not use it for the other purpose. When it will be used for the equipment with the microcomputers con...

5-3 Monitor Lamp   The equipment is incorporated in monitoring function of WATER TEMP, BATTERY CHARGING, OIL PRESSURE, Hz/OVERHEAT. Under normal condition, when the starter switch changes from STOP to RUN, all the lamps of BATTERY CHARGING, OIL PRESSURE and Hz/OVERHEAT turn ON. When the engine start...

5-4 Frequency Change Danger : Injuries z Frequency change should be done, after stopping the engine. Moreover, close doors and place locks during operating this equipment, to avoid injuries by unintentionally touching cooling fan and fan belt. Danger: Electric Shock z Never touch the frequency chang...

5-8 Voltage Adjusting Dial Adjust the dial whenever the AC Output adjustment is necessary. Set the dial in the center usually. <Caution> z When raising the voltage, the current is decreasing. (Use the output within the output capacity.) z In you raise the voltage exceeding the allowable voltag...

<Caution> z Use Diesel fuel, ASTM D975 No.2-D in the event ambient temperature reaches down to -5 ℃ . z The engine is designed to use either No.1-D or No.2-D Diesel fuel. However, for better economy, use No. 2-D Diesel Fuel whenever possible. At temperatures less than -7 (20 ℉ ), No.2-D fuel m...

8. Welding Operation 8-1 Selection – Welding Cable Select the cable with proper gauge, based on the allowable amperage and the length, per the table shown below. The welding capacity is to reduce if the small gauge cable is used. <Caution> z Welding cables should be used unstrained. When the w...

8-5 Welding Caution : Suffocation from welding fume z Be sure to wear a fume proof mask in operation, because welding fume contains poisonous gas and dust. Pay attention to the airflow direction and sufficient ventilation also in order to prevent from inhaling the fume. Caution : Injuries to eyes an...

② Adjust the current amperage by the current adjust dial, per the table below. Welding Current at the dial position Position Freq MIN 1 2 3 4 5 MAX Eco 40 60 100 140 180 220 240 50Hz 90 120 190 250 320 360 380 1 Person Single Use 60Hz 110 140 200 260 320 380 400 50Hz 50 70 100 130 160 180 190 2 Pers...

9-2 Output Limitation Please refer to the following table, because electric tools and home appliances cannot be judged only by the rated output or the power consumption due to the efficiency and character of the components. Applicable Load (For reference purpose only) Capacity (kW) 1-Phase 220-240V ...

10. Simultaneous Use of Welding and Generating The circuit breakers (3-P and 1-P) react on the AC power supply circuit only. In the simultaneous use of welding and generating, there sometimes happens overload to the engine. Refer to the following table and limit the AC power use. Limitation of AC Po...

Checking Time Checking Items Startup Check At 50hrs Every100 hrs. Every 200 hrs Every 400 hrs Every 1000 hrs Every 2000 hrs 1 Check and Supply Fuel ○ 2 Check and Supply Engine Oil ○ 3 Engine Oil Change 1 st ○ 2 nd or after ○ 4 Oil Filter Change 1 st ○ 2 nd or after ○ 5 Check/Add Water/Coolant ○ 6 Wa...

Shindaiwa Corporation         Head Office : ６−２−１１，Ｏｚｕｋａ−Ｎｉｓｈｉ，       Ａｓａｍｉｎａｍｉ−Ｋｕ，Ｈｉｒｏｓｈｉｍａ，       ７３１−３１６７，Ｊａｐａｎ Telephone: +81-82-849-2220 FAX: +81-82-849-2481 71905-94310 - 37 -