Schweigen GA-1200SPPAK - Manuals

IMPORTANT SAFETY INFORMATION Page 5 BEFORE INSTALLATION We recommend this appliance be installed or repaired by an experienced Home Appliances technician. Please see our website www.schweigen.com.au for a list of experienced installers.It is dangerous to modify any part of this appliance. Modificati...

IMPORTANT SAFETY INFORMATION Page 6 PRODUCT USE This product is designed for household use and should not be used for commercial applications.After use, always ensure that all controls are in the “OFF” position.When frying with a gas flame, take particular care not to allow the oil or grease in the ...

Page 7 1. Socket lead to Isodrive ® motor 2. Main power cord3. Single 200mm Outlet4. Computer board*5. Reducer6. Filters (depending on model filters vary in size)7. Lights8. Instruction and screws pack *IMPORTANT: The electronics MUST be accessible for servicing once installed, failure to do so, wil...

Page 8 OPERATION Electrical Tactile Keypad To obtain the best performance, switch the rangehood on a few minutes prior to cooking and leave running for at least 10 minutes after you have finished cooking.The buttons have the following functions:A.- Timer: When this function is activated, the blue li...

Page 9 CLEANING AND MAINTENANCE Latch A Catch A Figure 2 Figure 1 FILTERS • For your appliance to function effectively, regular maintenance is a must. • The function of the filter is to absorb the grease particles emitted during cooking. • Blocked filters and heavy oil deposits restrict airflow and ...

Page 10 SURFACES The surface of the rangehood can be cleaned with warm soapy water and a soft sponge / cloth. • Never use abrasive detergents, scouring pads, steel wool or solvents on ANY part of this appliance. • Rinse with clean water and ensure that the appliance is completely dry after cleaning....

Page 11 GLED SquareREPLACING THE LED BULB The life span of an LED bulb is at least 10 times that of a halogen bulb. If the globe needs to be replaced, proceed as follows:1. Unplug the respective connector (A).2. Press the tabs (B) inside the rangehood.3. Remove the LED.4. Put in the new LED and rein...

Page 12 INSTALLATION RANGEHOOD SIZE VS COOKTOP SIZE In addition to the size, the height of the rangehood above the cooktop is important to obtain the best performance. INADEQUATE Rangehood smaller than cooking zone ADEQUATE Rangehood same size as cooking zone OPTIMAL Rangehood larger than cooking zo...

INSTALLATION Page 13 OVERHEAD CABINET RANGEHOOD INSTALLATION POSITION It is important to consider the benchtop and overhead cabinetry depth before installing the rangehood.The information below is to be used as a guide only, drawings are not to scale and do not account for all circumstances. The coo...

INSTALLATION Page 14 MOUNTING LAWS AND REGULATIONS It is STRONGLY RECOMMENDED that the rangehood be installed centrally over the cooktop. This will greatly improve its performance.Minimum height from the hob top surface to the underside face of the rangehood:• 650mm electric cooktop• 650mm gas cookt...

Page 15 INSTALLATION Installation for GA-600S Y+20mm X+20mm Step 2 Remove the filters from the undermount. Step 3 To separate the fascia (A) and release it from the undermount (D), remove the 4 locking screws (E) The fascia will remain fixed due to the magnets. E D A E Filters Step 1 Cut the cabinet...

Page 16 INSTALLATION Step 5 Once (D) has been firmly attached, fix the fascia (A) to the rangehood (D) the magnets (B) will hold the fascia in place. Step 4 Fix the undermount to the cabinetry with appropriate screws, using the pre-drill holes in the undermount body (C). C C D A B

Page 17 INSTALLATION Step 6 Re-attach the fascia by securing it with 4 x locking screws (E). Step 7 Re-install the filters. E IMPORTANTPlease ensure all plastic protection on the rangehood and filters are removed before use.

INSTALLATION Page 18 Please DO NOT crush or kink the ducting. 1. Crushed or kinked ducting creates sharp corners that creates turbulence. This reduces the size and efficiency of the ducting, lowers extraction and may cause excessive noise. 2. Sweeping curves and taut ducting reduces resistance and t...

Page 19 INSTALLATION SYSTEM OVERVIEW 1. Isodrive ® Motor 2. Roof Seal Kit (Dektite) (Not Supplied)*3. Support Straps (Not Supplied)*4. Attach Duct to Bell-Mouth Adaptor using ring clamp. Please DO NOT rip the ducting. 5. Isodrive ® Motor Power Lead (Plug) 6. Rangehood to Isodrive ® Motor Lead (Socke...

Page 20 CONDENSATION INFORMATION COOKING WITH INDUCTION COOKTOPS Cooking with an induction (or similar) cooktop, may produce condensation on the rangehood.Unlike basic electric or gas cooking, induction cooktops heat food and liquid instantly, which in turn, produces vapours rapidly. Because of the ...

Page 21 TROUBLESHOOTING Before you contact the technical service department, make sure that the product is plugged in and power is supplied.• Do not take any action that will damage the product. Check electric c onnection. V oltage o f the electric ne tw ork should be be tw een 220 - 240V , r angeho...

TROUBLESHOOTING Page 22 SERVICE Lodging an Online Service RequestIn the event that the failure is not due to the faults mentioned in the Troubleshooting section, you can lodge an online Service Request. To lodge an online Service Request, visit our website www.schweigen.com.au/service-and-warranty a...

Page 23 TECHNICAL SPECIFICATIONS Model: GA-600SFeeding Voltage: 220-240V 50HzMax Lamp Power: 2 x GLED Square 65 x 65mm 2.1W 3.12V 3000k GA-600S 273 3 06, 6 551 17 . . GA-600S Thickness Scale: SCHWEIGWN Observations: Description: Model: 1:6 Date: 21/03/2019 Code: A3 D.IZQUIERDO Drawn by: CONFIDENTIAL...

Page 26 DISCLAIMER Under our policy of continuous product development, product specifications may change without notice. Prospective purchasers should therefore check with the retailer to ensure this publication correctly describes the products being offered for sale. All information supplied is to ...