Schweigen CC-PARA4SP2PAK - Manuals

Schweigen CC-PARA4SP2PAK Range Hood – User Manual in PDF format online.

Manuals:

User Manual

User Manual Schweigen CC-PARA4SP2PAK

Summary

Page 2 - Welcome; Thank you for purchasing your new Schweigen Isodrive system.

Page 2 Welcome Thank you for purchasing your new Schweigen Isodrive system. To get the maximum output from this unit, please read through this guide before use and installation. This guide contains important information on the correct use and maintenance of the unit, as well as important safety note...

Page 3 - Index; Safety Duct

Page 3 Index 1. Welcome _____________________________________________________________________________________2 2. Your Safety Receiving your rangehood ______________________________________________________________________ 4 Before Installation ________________________________________________________...

Page 4 - Before Installation; Electrical Cord; MUST BE; RECEIVING YOUR RANGEHOOD; Any damage or defects MUST be reported

Page 4 2. Your Safety This appliance is not intended for use by person/s (including children) with reduced physical, sensory or mental capabilities, or lack of experience and/or knowledge. Unless the person has been given supervision or instruction concerning the use of the appliance by a person res...

Page 5 - Recommended Installation Distance

Page 5 2. Your Safety This guide is for the installation of the Isodrive motor system after the rangehood has been mounted on the wall or roof. (Refer to rangehood installation manual on how to install the rangehood). NOTE: All PVC pipe and SteelFlex ™ ducting measurements are referring to inside me...

Page 7 - Isodrive Motor; Included in each box:; NOTE

Page 7 3. Description Isodrive Motor Included in each box: 1. Isodrive 1600 motor (405W x 220H mm approx.) Approx. 3 metre, 10amp cable and standard male plug 2. Fire resistant 150mm (160mm OD 1 ) PVC riser pipe Note: Cable cut-out at the bottom end only 3. SteelFlex ™ safety ducting Approx. 6 metre...

Page 8 - Roof Installation; protrudes at least 50mm

Page 8 4. Installation Roof Installation Recommended duct length: 1600 motor — 5 to 6 metres. Mount 150mm (ISD) rigid PVC pipe securely to beams, trusses or other appropriate structures: refer figure 1. The pipe should be mounted vertically with the roof penetration being sealed using a Dektite or o...

Page 12 - Installation Through Wall with Back Draught Shutter

Page 12 Installation Through Wall with Back Draught Shutter Due to the weight and to create stability for the Isodrive 1600 motor, it is require to use a hanging bracket. Warranty will be void if a hanging bracket is not used. F igure 7 *Optional parts are available from Schweigen, please contact 13...

Page 13 - Flat Roof Installation; IMPORTANT

Page 13 Figure 4 Flat Roof Installation Flat roof mounting using optional mounting flange*. PED Engage locking screws in holes Seal 3 holes in stepped surface Seal between mounting flange and cover Up-stand and capping Power supply cord passing through pipe slots NOTE: Cut 150mm PVC stormwater pipe ...

Page 14 - Fan Unit Shutter Assembly for Isodrive 1600

Page 14 Fan Unit Shutter Assembly for Isodrive 1600 1. Assemble by fitting shutter assembly into fan inlet shroud moulding, ensuring that attaching screws align with holes. Alignment can be checked visually by folding in shutter flaps. 2. Fully tighten both screws and re-check fitment into holes. 3....

Page 15 - Twin Motor Installation

Page 15 Twin Motor Installation (suitable for rangehoods with two 200mm outlets) Where two motors are to be used, follow the method below. Each motor should have a separate flue pipe. Refer figure 9. The two motors can be wired by an electrician. Connect to main power Connect to motor Computer box C...

Page 17 - Single Motor Installation Twin 200mm Outlet

Page 17 Figure 11 Roof mount option Single Motor Installation Twin 200mm Outlet (suitable for rangehoods with two 200mm outlets and one 1600 Isodrive motor) This is for use where one motor is to be used and there are two 200mm outlets, refer figure 11. Try to keep length of SteelFlex ™ ducting as ev...

Page 18 - Measurements for Isodrive 1600

Page 18 5. Measurements Measurements for Isodrive 1600 (Not to Scale) 148mm 90mm 35mm 405mm 220mm 440mm 160mm 225mm 190mm Dektite Motor weight: 6kg net.Shutter assembly is not shown in the diagram.

Page 19 - A list of preferred Schweigen

Page 19 6. SteelFlex ™ Safety Duct SteelFlex ™ Safety Ducting SteelFlex ™ safety ducting must be fully extended and cut to the required length upon installation. Maximum fan performance will not be achieved unless the ducting is fully extended. Failure to fully extend ducting results in a smaller ai...

Page 20 - Assembling SteelFlex

Page 20 6. SteelFlex ™ Safety Duct Assembling SteelFlex ™ Safety Duct SteelFlex ™ safety duct must be secured to either the bell-mouth adapter ring or a 200mm mounting pipe. 1. Slide the steel ring clamp over the end of the duct then insert the bell-mouth adapter ring into the duct end Parts require...

Page 21 - Shallow Roof Space; Important Note

Page 21 6. SteelFlex ™ Safety Duct Shallow Roof Space In shallow roof spaces, do not crush or kink SteelFlex ™ ducting, as it will reduce air flow severely. 90 degree curve made of PVC or galvanise can be used as a substitute for the bend, refer to figure 12. Figure 12 Figure 13 Use 90 degree curve ...

Page 22 - Securing SteelFlex; Option 1

Page 22 6. SteelFlex ™ Safety Duct Securing SteelFlex ™ Safety Duct SteelFlex ™ safety duct must be installed with supports at maximum intervals of 1.5 metres. SteelFlex ™ safety ductwork can be supported by using good quality gaffer or aluminium foil tape. Provided that it does not restrict the int...

Page 23 - Parts List for Isodrive 1600

Page 23 7. Parts List Parts List for Isodrive 1600 9 3 1 5 4 6 7 3 18 19 20 21 22 23 17 16 11 12 13 14 15 24 25 2 10 23a OR For wall installation with no back drought system or flat roof installation.

Page 24 - Number

Page 24 7. Parts List Parts List for Isodrive 1600 Number Part Number Description Quantity 1 P1120 M4X160mm Pan Head Screw 4 P1120N M4 KEPS Nut (not shown in figure) 4 5 P1114 Capacitor 3.5μF 1 9 P1100 Fan Motor Mounting Bracket 1 10 P1102 Fan Base Spinning 1 11 P1113 Heyco Snap Bushing 1 12 P40113 ...

Page 26 - Warranty; Disclaimer

Page 26 9. Warranty / Disclaimer Warranty (See warranty for more information) Isodrive motor has a 10-Year replacement product warranty.* The consumer is responsible for any charges associated with removal of the faulty unit and installation of the new unit. The customer is also responsible for any ...

Page 27 - Notes