Samson EB 8331-1 EN - Manuals

Page 2 - Contents

Contents Page 1 Design and principle of operation . . . . . . . . . . . . . . . . . . . 5 1.1 Additional equipment . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.2 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Installation . . . . . . . . . . . . . . . . . . ....

Page 3 - Safety instructions; General safety instructions; Proper transportation and storage are assumed.

EB 8331-1 EN 3 Safety instructions General safety instructions 4 Assembly, start-up and operation of this device may only be performed bytrained and experienced personnel familiar with the product.According to these mounting and operating instructions, trained personnelrefers to individuals who are ...

Page 5 - Additional equipment; Design and principle of operation

1 Design and principle ofoperation The Type 3374 Electric Actuator is used inindustrial plants as well as in heating, venti-lation and air-conditioning systems.The linear actuator is suitable for form-fit at-tachment to various SAMSON valve series,depending on the version with or withoutfail-safe ac...

Page 6 - Technical data

1.2 Technical data 6 EB 8331-1 EN Design and principle of operation Actuator Type 3374 -10 -11 -15 -21 -26 -31 -36 Version with Yoke Ring nut Yoke Ring nut Yoke Ring nut Safety function Without Stem extends Stem retracts Rated travel mm 30 15 30/15 15 Actuating time forrated travel s 240 120 240/120...

Page 8 - Remove protective covers and unscrew; Installation

2 Installation 2.1 Mounting position Installation depends on the mounting posi-tion of the valve. However, do not install theactuator suspended downwards. Note! Manual override is only possible in actua-tors with fail-safe action when the powersupply is connected (see section 4.1). 2.2 Attachment to...

Page 9 - Attachment to Series V 2001,

EB 8331-1 EN 9 Installation Fig. 2 · Attachment to the valve 1 2.1 345 6 x 1 2.3 7 3 48 9 10 5 1 2.2 7 3 10 4 5 Attachment to Series V 2001, Type 3260 DN 65 to 150 and Type 3214 DN 65 to 100 Attachment to Series 240 Attachment to Type 3214DN 125 to 250 1 Actuator 2.1 Actuator yoke 2.2 Valve yoke 2.3...

Page 10 - Electrical connections

3 Electrical connections Upon installation of the electric ca-bles, you are required to observe theregulations concerning electricalpower installations according to DINVDE 0100 as well as the regulationsof your local power supplier. Establish electrical connections as indicatedon the circuit diagram...

Page 12 - Use motor or manual override to move; Use motor or manual override to move; Operation and setting

4 Operation and setting 4.1 Manual operation of theactuator To operate the manual override, place4 mm hex wrench on the red actuator shaftlocated at the side of the housing. The hexwrench is delivered with the actuator. It isattached to the bottom of the housing. Manual override is only possible in ...

Page 14 - Setting the digital positioner; Setup with operating modes

4.3 Setting the digital positioner In the actuator version with digitalpositioner, the travel is calibrated automati-cally, allowing the travel (controlled variablex) and the input signal (reference variablew) of the positioner to be matched in thebest possible way. Additionally, the digitalposition...

Page 18 - Limit switches; Retrofitting additional electrical equipment

5.1 Limit switches The retrofit kit (order no. 1400-8830 ) is re- quired to install limit switches. If the actuatoris not already equipped with potentiometersor a positioner, the basic unit (order no. 1400-8829 ) is also required. The unit in- cludes the spindle gear (2) and the interme-diate gear (...

Page 20 - Potentiometers; Push the actuator board back into its

5.2 Potentiometers Actuators with a digital positioner cannot beequipped with potentiometers. To install the potentiometers, an actuatorboard with the appropriate potentiometersand gears (12 and 13) is required. If the actuator is not already equipped withlimit switches, the basic unit (order no. 14...

Page 21 - Actuators with a digital positioner

5.3 Digital positioner To install a positioner, a corresponding ac-tuator board and TROVIS-VIEW 3374 andconnecting cable 0450-1978 are necessary. If the actuator is not already equipped withlimit switches, the basic unit (order no. 1400-8829 ) is also required. The unit in- cludes the spindle gear (...

Page 22 - the actuator; ing mode

5.3.1 Calibrating the positioner To calibrate the positioner, proceed as de-scribed in section 4 of EB 8331-2 EN. 5.3.2 Simplest method to calibrate the actuator If tools such as the TROVIS-VIEW software,PC etc. are not available for calibration ofthe actuator and the actuator operation withmaximum ...

Page 23 - Dimensions in mm; Version with yoke

6 Dimensions in mm EB 8331-1 EN 23 Dimensions in mm 120 50 15 (30) 294 60 193 90 (75) 204 30 (15) Version with yoke Version with ring nut Stem connector