Royal Sovereign RSS-1050 - Manuals

1. FILM-UPPER 8. FOOT SWITCH 2. FILM-LOWER 9. REMOTE CONTROL SWITCH 3. TAKE-UP (ASS'Y-TAKE-UP) 10. CONTROL PANEL 4. IDLER BAR (UPPER) 11. PRESSURE LEVER 5. TABLE-FRONT 12. TENSION CONTROL KNOB 6. SHOE-HEATER,UPPER 13. ALIGNMENT KNOB 7. ASS'Y-STAND 14. TAKE-UP SWITCH NAMES OF MAJOR PARTS OF MACHINE 1...

1. HOW TO CONTROL TENSION 2. HOW TO ADJUST ALIGNMENT Location control device is used when the edges of the lamination are unjustified. As the drawing shows, when the alignment knob is turned clockwise, the upper film is to left. Once proper alignment is reached, turn the Locking Nut tight against th...

1. Set the glossy side of upper/lower film to face the heat. ( Glossy side is PET film and matte side is thermal polymer laminating film.) 2. Like picture 1, insert core into the left side of upper/lower film shaft. 3. Like picture 2 and 3, insert core into the right side of upper/lower film. 4. Lik...

1. HOT FILM 10. After checking the status of lamination, Place the pressure lever at the proper lamination mode. 6. Allow some of the film with melted resin to stick to the Guiding Paper. 7. Repeat step 5 with lower roll film then stick it to the Guiding Paper. fed through to the rear roller without...

1. For setting, pull the pressure lever out and turn the lever to following the indication. 5. Laminating : Mode that you can do laminate 25mic(1mil) to 250mic(10mil) 2. 10~13mm Board : Mode that you can laminate 10~13mm(1/3" to 1/2") 3. 5mm Board : Mode that you can laminate 5mm(1/4") h...

You can manipulate speed and temperature with the LCD controller. We designed the LCD panel for user convenience by adopting memory working condition. INSTRUCTIONS FOR CONTROL PANEL ***Terms*** LCD DISPLAY BUTTON - 11 -

2. FUNCTIONS OF BUTTONS : Upper shoe temperature controller : Lower shoe temperature controller : Speed controller : Choose memorized working condition : ① Increase temperature ② Increase speed ③ Restore the memorized working setting : ① Decrease temperature ② Decrease speed ③ Restore the memorized ...

1) Memorize working condition 1.Operator can memorize 9 working conditions. 2.Each time you press the button, buzzer is ringing. 3.find the condition number you are willing to memorize working condition by pressing button. 4.When you finish setting upper/lower temperature and speed, you can press th...

6. It is ready when the LCD window shows 9.Push 11. Push 4. Set pressure lever to "Laminating" position.5. Increase temperature of the hot shoe. If the temperature is memorized for the button to choose the correct location. 7. To set the film tension properly, please use the Tension Adjustme...

1. It is convenient to use the remote control in the back of machine while laminating.2. It is also convenient if you use Foot Switch while laminating HARD BOARD.3. "RUN", "STOP", "REV" buttons on Remote Control have same functions with the ones on Control Panel. 4. Press Foo...

2. Prevent children from accessing the machine. Extreme Heat Will Cause Injury 4.Make certain that the machine is connecterd to an adequate power source. 1.Do NOT Allow the machine to run with only one roll of film installed. The melted resin will adhere to one roller and ruin future laminations. 2....

Rollers do not operate 1. Power cord may not be plugged 1. Check the power cord after press RUN in. 2. Check the switch is on button. 2. Power switch is at OFF mode. 3. Check the emergency switch 3. Emergency switch may be at is off ON mode. 4. Release STND-BY switch by 4. It may stay at STAND-BY mo...

1. DURATION OF LIMITED WARRANTY One (1) year from the date of "Buyer's" receipt of delivery. 2. INSPECTION and CLAIMS It is the "Buyers" responsibility to inspect all merchandise immediately upon receipt. Any claims must be submitted to the "Seller" in writing, along with ade...