Royal Sovereign RSL-382S - Manuals

Page 2 - Table of Content; Safety Precautions

3 ~ 3 4 ~ 10 4 ~ 6 6 ~ 7 7 ~ 9 9 ~ 10 11 ~ 11 12 ~ 14 12 ~ 12 13 ~ 13 13 ~ 13 13 ~ 13 13 ~ 13 13 ~ 14 14 ~ 14 15 ~ 16 17 ~ 19 20 ~ 25 26 ~ 29 30 ~ 33 2.5) Poor Lamination Quality ………………………………………………………… 2.1) Rollers Not Heating …………………………………………………………… 2.2) Rollers Over Heating ……………………………………………………………...

Page 3 - Safety Precautions; Safety Precaution; Keep flammable and wet objects away from the machine .

1. Safety Precautions Safety Precaution 1 Failure to comply any of the following safety procedures could result in serious injury. Please read the instructions carefully and keep for future reference. 1. Only a licensed electrician should install wiring and outlet for the laminator. 2. Ensure the un...

Page 4 - Rollers Not Heating; Press “C/HOT” button on the control panel to change the mode.; Heating wire is not connected to the main PCB.; a. Connect the upper and lower heating wires to the main PCB.; MEASURE

Note: While repairing: a. Make sure the power plug is unplugged from the power outlet. b. Open both side covers and rear cover. c. Be sure to follow the steps below in order. 2.1 Rollers Not Heating 1. Improper laminating mode. 2. Heating wire is not connected to the main PCB. 3. Blown (burnt) upper...

Page 6 - Connector-Wire Sensor

a. Replace the PCB Main. 2.2) Rollers Over Heating 1. Lower and upper heat sensors are reversed on the PCB Main. 1. Wires for lower and upper heat sensors are reversed on the main PCB. a. Reverse the heat sensors. a. Replace the T/Fuse wire located on the left-hand side. 2. Defective T/Fuse wire. 4 ...

Page 9 - CAUSES; Motor Fuse

7. Blown motor fuse. a. Replace the motor fuse located above the main power switch. 8. Defective main motor. a. Replace the main motor. 9. Defective main PCB. a. Replace the main PCB. 2.4) No Main Power 1. No electricity. 2. Blown main fuse. 3. Disconnected main power wires. 4. Defective transformer...

Page 10 - a. Check that the main power wires are properly connected.; Transformer is defective; Main Fuse

3. Disconnected main power wires. a. Check that the main power wires are properly connected. 4. Transformer is defective a. Replace the transformer. 8 10 Main Fuse Main Power Wires Transformer

Page 11 - Poor Lamination Quality

Problem: Straight wave lines across the output. Cause: Excessive front roller pressure. Measure: Loosen the front roller pressure. Problem: Concave waves in the lamination. Cause: Excessive rear (pulling) roller pressure. Measure: Loosen the rear back roller pressure. Problem: Angled waves on both s...

Page 12 - Replacing the Left Cover; a. Replace the Left Cover by loosening four Left Cover screws.; Figure 1

Note: While replacing parts: a. Make sure the power plug is unplugged from the power outlet. b. Open both side covers and rear cover. 3.1 Replacing the Right Cover. a. Take out the pressure lever (Figure 1) and four cover screws using Phillips screw driver (Figure 2). b. Pull out the male control pa...

Page 13 - a. Disassemble Right and Left Covers (Refer to “; ” and “

3.3 Replacing Rear Cover a. Take off the left and right covers. b. Take out the four screws from frames,two screws of each side(Figure 5,Figure 6) 3.4 Replacing the Main PCB a. Remove the rear cover and label all the wires before unplugging from the Main PCB. b. Detach the Main PCB from 6 white plas...

Page 14 - Replacing the Cross Cutter; d. Assemble the Cutter by reversing the above steps.

c. Take out the broken heater. Figure 11 Note: a. When inserting the heater into the roller, rotate the heater slightly and push the rod in gently. b. Use an air blower to blow out the broken pieces of heating rod. (Please ensure that no one is standing on the other side.) 3.7 Replacing the Cross Cu...

Page 15 - Use Screwdriver; to; Checking for over all tension

4.1 Adjusting Take-up Shaft Speed 1.Main rollers and take-up shaft speed is not synchronized. Adjust take-up shaft speed,by loosenning or tightenning the knobAccording to label-take up. 4.2 Adjusting front and rear rollers when the machine is running, check that the top and the bottom films are fed ...

Page 27 - Frame, Roller and Other View

Frame, Roller and Other View 25 1 013LR2012F FRAME-SENSOR 2 013LR2087A FRAME-L 3 013LR2088A FRAME-R 4 013LR3002K FRAME-CUTTER 5 013LR3009A FRAME-REAR 6 013LR3021A PLATE-MIDDLE 7 013LR3075A BASE-FRONT 8 013LR3076A BASE-REAR 9 013LR4004A FRAME-COVER SAFETY 10 014LR3001A TABLE-FRONT 11 015LR2001B IDLE ...

Page 29 - RSL-382S Expolde View

RSL-382S Expolde View 27 1 013LR2012G FRAME-SENSOR 2 013LR2087A FRAME-L 3 013LR2088A FRAME-R 4 013LR3002H FRAME-CUTTER 5 013LR3035A FRAME-REAR 6 013LR3036A PLATE-MIDDLE 7 013LR3069A BASE-FRONT 8 013LR3070A BASE-REAR 9 013LR4004A FRAME-COVER SAFETY 10 014LR3001B TABLE-FRONT 11 015LR2010A IDLE BAR LOW...