Royal Sovereign RSL-380 - Manuals

Page 2 - Exploded Drawings; Table of Content; Safety Precautions

3 ~ 3 4 ~ 10 4 ~ 6 6 ~ 7 8 ~ 9 9 ~ 10 11 ~ 11 12 ~ 18 12 ~ 12 13 ~ 13 13 ~ 14 14 ~ 14 15 ~ 15 15 ~ 16 16 ~ 17 17 ~ 18 19 ~ 19 20 ~ 23 24 ~ 34 35 ~ 38 4.Adjustments …………………………………………………………………………………… 3.8) Replacement of Motor……………………………………………………………………… 5. Parts List ………………………………………………………………………………………… 2...

Page 3 - Safety Precautions

3 1. Safety Precautions 3 Failure to comply any of the following safety procedures could result in serious injury. Please read the instructions carefully and keep for future reference. 1. Only a licensed electrician should install wiring and outlet for the laminator. 2. Ensure the unit is plugged in...

Page 5 - Rollers Not Heating; The wire connector from the heater is disconnected; Before troubleshooting, be sure to; ) Test if the connector wire is; CAUSES; The wire connector from the heater is

2.1 Rollers Not Heating 1. The wire connector from the heater is disconnected with MAIN PCB.(except RSL-380) 2. The Wire-Temp Fuse is disconnected. 3. The Main Fuse is defective.(except RSL-380) 4. The Bi-metal is defective. 5. The heater in the roller is defective. 6. Main PCB is defective. Before ...

Page 6 - The Wire-Temp Fuse is disconnected

2 The Wire-Temp Fuse is disconnected 1) Test if the Wire-Temp Fuse is disconnected with Multi-tester. 2) If disconnected, replace it with new one. 3. MAIN FUSE is disconnected.(except RSL-380) 1) Test if the Main Fuse is disconnected with Multi-tester. 2) If disconnected, replace it with new one. 1)...

Page 7 - Rollers Not Heating; The heater in the roller is defective.; Before trouble shooting, be sure to disassemble; MEASURES

5. The heater in the roller is defective. 1) Test if the heater is disconnected with Multi-tester. 2) If disconnected, replace it with new one. Replace Main PCB with new one according to How to replace Main PCB only when all of the above mentioned heater wire, wire thermal fuse, heater and Bi-metal ...

Page 10 - Rollers Not Running; Before troubleshooting, be sure to disassemble; MICRO; MOTOR

2.3 Rollers Not Running 1. Safety cover is not in proper position. 2. Wire-Motor's connector is disconnected. 3. Film is jammed on the rollers. 4. Main PCB is defective. 5. Main motor is defective. Before troubleshooting, be sure to disassemble the Right cover ,the Left cover and the Rear cover. Ref...

Page 11 - Replace Motor with new one according to How to replace the Motor.; MAIN SWITCH

3. Film is jammed on the rollers. 1) First press reverse button. 2) Pull jammed film slowly to the back of the machine. 3) If you feel film is jammed again, stop pressing reverse button. 4) press run button, and then pull jammed film to the back of the machine. 4. Main PCB is defective Replace Main ...

Page 13 - Poor Lamination Quality

13 2.5 Poor Lamination Quality Problem: Straight wave lines across the output. Cause: Excessive front roller pressure. Measure: Loosen the front roller pressure. Problem: Concave waves in the lamination. Cause: Excessive rear (pulling) roller pressure. Measure: Loosen the rear back roller pressure. ...

Page 14 - ) Unfasten 4 screws holding the Right; cover and disassemble the Right cover.; ) Unfasten 4 screws holding the Sub-PCB

Turn off the switch of the machine and then pull out the power cord plug from the electrical outlet. 3.1. Right Cover 1) Unfasten 4 screws holding the Right cover and disassemble the Right cover. <RSL-2701/2701U> <RSL-380> 2) Pull out the male connector from the Sub-PCB . 3) Unfasten 4 s...

Page 15 - and disassemble the Left cover .; ) Disassemble both the Right cover and the Left cover.

3.2. Left Cover 1) Unfasten 2 nuts holding the Knob Tension 2) disassemble the Knob-Tension. 3) Unfasten 4 screws holding the Left cover and disassemble the Left cover . 4) How to assemble is the reverse order of how to disassemble , 3)→2)→1). 3.3. Rear Cover 1) Disassemble both the Right cover and ...

Page 16 - white plastic supporters.; PCB SUPPORT

3) Disassemble Wire connect to MAIN S/W, POWER CORD. 4) Disassemble MAIN S/W and POWER CORD. 5) How to assemble is the reverse order of how to disassemble , 4)→3)→2)→1). 3.4. Main PCB 1) Pull out all the connectors from the main PCB. 2) Detach the main PCB from 4 white plastic supporters. 3) How to ...

Page 17 - ) Unfasten 2 screws holding the heater and disassemble the wire.

3.5. Sub PCB 1) Refer to No 1.(Replacement of cover-R) 3.6. Heaters 1) Disassemble both the Right cover and the Left cover (Refer to No.1, No.2) . 2) Unfasten 2 screws holding the heater and disassemble the wire. < Detachment 2 screws holding the heater> 3) Unfasten 2 screws and disassemble th...

Page 18 - and the heater enter the roller smoothly.

4) Disassemble the Bush-Roller, Up holding the upper heater. < Take off Bush-Roller, Up from Laminating Roller > 5) Disassemble the lower and upper heater from the roller cautiously 6) How to assemble is the reverse order of how to disassemble , 5)→4)→3)→2)→1). When inserting the heater into t...

Page 19 - ) Disassemble the Right cover , the Left

3)a. Disassemble Frame upper with Cross Cutter.(RSL-2701/2701U) b. Disassemble Cross Cutter from the Frame-Cutter.(RSL-380) <RSL-380> 4) Disassemble the Cross Cutter from the Frame-Upper.(RSL-2701/2701U) <RSL-2701/2701U> 5)a. How to assemble is the reverse order of how to disassemble , 4...

Page 21 - Adjusting Front and Rear Roller; with different thickness of substrates.; Check above steps 2 through 4; with; Checking for over all tension; Pressure; Use Screwdriver; to adjust the roller pressure:; Figure B

21 Adjusting Front and Rear Roller when the machine is running, check that the top and the bottom films are fed in without any wrinkles. 19 with different thickness of substrates. 5. Check above steps 2 through 4 with 3mil & 5mil films. lines indicate that it has less pressure at that point. 4 ....

Page 22 - SVC Parts List

P NO. DATE 1 013LR2026A BASE-FRONT AL6063 013LR2033A 20050317 013LR3075A 20060710 2 026004005A FOOT NATURAL RUBBER 3 013LR2027A BASE-REAR AL6063 013LR2032A 20050317 013LR3076A 20060710 4 350LR3008A PCB-MAIN ASS'Y FR-4 Chang the AC IN and Heater's connector 20050423 5 34000S009B POWER TRANSFORMER-OTH...

Page 32 - Frame, Roller and Other View

Page 33 - Wire, Power core and Control PCB

Page 38 - Wire, Front Table and Safety Cover

Wire, Front Table and Safety Cover 34 NO P a r t N/ O P a r t Na m e 52 014LR3001B TABLE-FRONT 53 145LR3002A GUIDE-DOCUMENT 54 023LR4002A KNOB-BOLT GUIDE 55 111LR4006A BOLT-GUIDE 56 013LR4004A FRAME-COVER SAFETY 57 021LR3024A COVER-SAFETY 58 141LR4043A FRONT TABLE SAFETY LEVER 59 111LR4018A SCREW-H ...