Royal Sovereign 1650 - Manuals

NO RSR-1050 RSR-685 12345 789 1011121314 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ X ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ X ○ X X ○ ○ ○ ○ PART NAME FRAME-GUIDE,PAPER ○ ○ NAMES OF MAJOR PARTS OF MACHINE ○ ○ FOOT SWITCH RSH-1050 ○ RSH-1650 ○ ○ ○ ○ TABLE-FRONT ○ ○ ○ ASS'Y-STAND TAKE-UP SWITCH TAKE-UP BOBBIN...

1. Disassemble both the Right cover and the Left cover. (Note :Turn the fastening nut of the Emergency switch counterclockwise and disaasemble the Emergency switch before disassembling the Right cover.) 2. Disassemble the Rear cover. 3. Disassemble the power switch bracket which is located at the le...

take -up motor. 7. Assemble the Right cover letting the wires go through the slot which is located at the rear side of the Right cover.8. Put the Power switch bracket on the Plate-Rewinder L and fasten it with two M4 screws. How to install the unwinder Female Connector from take-up motor Male Connec...

1. Put the Plate-Unwinder R on the inner side of the frame as shown in the following figure and fasten it with four M6 hexagonal bolts. 2. Put the Plate-Unwinder L on the inner side of the frame as shown in the following figure and fasten it four M6 hexagonal bolts. SETTING UP FILM 주 름 방 지 부 열 판 주 름...

1. Set the glossy side of upper/lower film to face the heat. ( Glossy side is PET film and matte side is thermal polymer laminating film.) 2. Like picture 1, insert core into the left side of upper/lower film shaft.3. Like picture 2 and 3, insert core into the right side of upper/lower film. 4. Like...

RSH-1050/1650 RSR-685/1050 1. Set up cold film below the upper bar of the machine (Set the same as method of HOT film for protect paper of lower part) 2. Set the pressure Lever to the 15mm, open mode 3. Insert a piece of wide cardboard (guiding paper/carrier) between the rollers 4. Pull the film fro...

1. For setting, pull the pressure lever out and turn the lever to following the indication 2. Open/15mm : for laminating 15mm(0.6") thick board (RSH-1050/1650) 3. 10~13mm : for laminating 10~13mm （ 0.4" to 0.5") thick board 4. 5~7mm : for laminating 5~7mm(0.2" to 0.27") thick boa...

It displays you the last working condition when turned on. 2. Is displayed when the preset temperature is reached. 3. Blinking Indicates to wait till blinking stops. Current temperature is higher or lower than the preset temperature. 4. Saving electricity status. 5. Temperature 1) Shows the preset t...

: Speed controller : Choose memorized working condition : ① Increase temperature ② Increase speed ③ Restore the memorized working setting : ① Decrease temperature ② Decrease speed ③ Restore the memorized working setting : Cold and Hot mode change : Check current temperature : Saving electricity whil...

to 160°C (320°F). 2. Temperature setting of upper roller Press and you will see the LCD screen is blinking 6 times. Before blinking is finished, press or to set the temperature 3. Set temperature of lower roller Press and choose the arrow button the same way to set temperature of upper roller. 4 Eac...

blink five times.2.After this, it automatically returns to the previous state. 1.You can do cold lamination with this function. 2.Press the button to show "Cold" on the display. 3.Speed will always show 2. 4.Speed can be varied 1 or 4 by selecting button. 5.You release the machine from cold ...

condition wouldn’t work. Press the button and it will revert to the previous working.3. When machine runs, you can’t change it to the mode. In this case, press the button and turn the machine to the mode. 1. When press button the present numbers of length and papers laminated will be shown on the sc...

2. Set the pressure lever to the “Laminating mode” 3. Increase roller temperature. If you already memorized special working condition, press button and choose right condition by using or button. 4. When it’s ready, you will see ready sign on the screen and the buzzer will ring. 5. Press the button. ...

If it happens, the speed needs to be lowered by one speed level and started againafter signal on the LCD window. 3. In case of wrinkling or rolling of film due to wrong position of document, is needed to be keeping pushed in order that document could come out to the front with buzzer sound. 4. When ...

4. After pressing the button choose and set proper speed by using the and button.5. It is when ready is show on the screen and the buzzer rings three times. sound three times. 6. Turn on the take up device and set the proper film tension by pressing the button. Lower tension would make better operat...

4. Press Foot Switch one time for "RUN", press one more time for "STOP". (Don't keep pressing) 5. After use of Remote Control, attach it to the left side of rear of machine **Cross Cutter** 1. It is on the back side of the machine. 2. After lamination, move cutter to a point about 1/...

Extreme Heat Will Cause Injury 3.Place the machines on the plated place so that 4.Make certain that the machine is connecterd to an adequate power souce. 5.Do not use any other purposes other than Lamination. 1.Do not allow the machine to run with only one roll of film installed. The melted resin wi...

4. It may stay at STAND-BY mode. press the STND-BY button *Hot roller is not heater 1. It is set at the cold mode 1. Change the function to hot up. 2. Memorized temp may be lower lamination. than atmosphere temp. 2. Set proper temperature for the work *Wrinkled lamination 1. Film tension is not prop...

a Sovereign authorized service representative, or damage caused by a natural calamity such as fire or earthquake and etc… 3. Customers will bear the expense of Transportation fee and delivery fee of the damaged machine. 110 5 1 75 micron Remark Func'No Preset Speed & Temperature Adjustment Speed...