Robertshaw 9620 - Manuals - manualsarea.com

Page 2 - Features; Step 1: Replacing Existing Thermostat; FIGURE 1

Features • Four preprogrammed E NERGY S TAR ® setpoints for each day of the week • Quickset™ programming for quickly programming all days of the week simultaneously • Energy Efficient Recovery (EER™) • Residual cooling for added air conditioning efficiency • Two AA ENERGIZER ® brand batteries retain...

Page 3 - TABLE 1; Remove existing thermostat base from wall.; Recycling Thermostat; NOTE; OFF; Turn off power to the heating and cooling systems.

TABLE 1 Old Terminal New Label Description R, V-VR or VR-R R 24 VAC Y, Y1 or M Y1 Stage 1 Cooling/Heating Circuit O or R O Reversing Valve (Cooling Mode) B B Reversing Valve (Heating Mode) G or F G Fan Contactor Circuit Y2 Y2 2nd Stage Cooling Circuit W1 or W2 or W-U W2 2nd Stage Heating Circuit L o...

Page 4 - NOTE: Enclosed plastic; Align base with plastic anchors and feed wires through opening; MOUNTING HOLES

3. Place AUTO-ON switch into AUTO position. 4. Remove the cover using a coin or screwdriver (Figure 2). FIGURE 2 5. Place thermostat against the wall at desired location. Make sure wires will feed through opening on base of thermostat. 6. Mark placement of mounting holes (Figure 3). Set base aside. ...

Page 5 - FIGURE 4

10. Secure base to wall with supplied screws. 11. Terminal screws are loosened. Insert wires into terminal strip (Figure 4) matching the label to the corresponding terminal (seeWiring Diagrams below). Tighten screws. 5 9620 WIRING SAMPLE #1 Y1 E G W2 C L R Y2 Typical heat pump with cool active rever...

Page 6 - TERM

6 12. Install two AA ENERGIZER ® brand batteries or equivalent into battery compartment. Be sure to match positive (+) ends of batteries withpositive (+) battery terminals in the battery compartment. 13. Replace cover on thermostat by snapping into place. 14. Turn on power to system. Test thermostat...

Page 7 - Step 3: Testing the Thermostat; switch into the COOL position

Step 3: Testing the Thermostat WARNING: DO NOT SHORT (JUMPER) ACROSS TERMINALS OF GAS VALVE OR SYSTEM CONTROL TO TEST OPERATION. THIS WILL DAMAGE THE THERMOSTAT AND VOID YOUR WARRANTY. CAUTION: D O NOT SWITCH SYSTEM TO COOL IF THE TEMPERATURE IS BELOW 50°F (10°C). T HIS CAN DAMAGE THE AIR CONDITIONI...

Page 8 - Step 4: Customizing Your Thermostat

Step 4: Customizing Your Thermostat ◆ Set Time of Day, Day of Week,Temperature Differential,Residual Cooling 1. Press SET and PROG/MAN. Release simultaneously. Press or to change time of day. 2. Press Press to change day of week. 3. Press Press to change 1st stage temperature differential. NOTE: T H...

Page 9 - Step 5: Setting the Program

◆ Changing Fahrenheit (F) to Celsius (C) Press and hold SET. Press Release both simultaneously. ◆ Energy Efficient Recovery (EER™) The Energy Efficient Recovery (EER™) feature looks ahead up to 2 hoursprior to the end of the setback (or set-up) period to begin monitoring per-formance and calculating...

Page 11 - SUMMER; Begin Programmed Operation; until indicator is in PROG position.; Temporary Program Override; To temporarily increase or decrease temperature:

11 > > ET PROG/MAN C PROG MAN PROG MAN SET PROG/MAN COOL-OFF-HEAT-EM AUX CHECK EMER AUTO - ON > > > > PROG MAN SET PROG/MAN COOL-OFF-HEAT-EM AUX CHECK EMER AUTO - ON > > PROG MAN SET PROG/MAN COOL-OFF-HEAT-EM AUX CHECK EMER AUTO - ON > > AUTO - ON SUMMER WINTER COOL-OFF...

Page 12 - Manual Operation; to; Reset

12 ◆ Manual Operation 1. Press PROG/MAN until indicator is in MAN position. 2. Press or to adjust temperature settings. ◆ Reset To reset the thermostat to factory preprogrammed conditions, press the RESET button located beneath the lower left cornerof the display. PROG MAN SET PROG/MAN COOL-OFF-HEAT...

Page 13 - If problems with thermostats cannot be resolved, call:; Troubleshooting; SYMPTOM REMEDY; LED Indicators

13 If problems with thermostats cannot be resolved, call: Technical Support: (800) 445-8299 Monday-Friday 7:30-5:30 CST Troubleshooting SYMPTOM REMEDY Thermostat does not turn on system. Check wiring.(See Installing Model 9620 Thermostat ) Check fuse. Replace with 3 ampfuse if fuse has opened. Fivem...

Page 14 - Five-Year Limited Warranty; warrants to the original contractor installer, or to; Maple Chase Company; agrees to repair or replace at its option any thermo-; Maple Chase Company; shall not be liable for any; Uni-Line North America; Warranty Claims Department

14 Maple Chase Company2820 Thatcher RoadDowners Grove, Illinois 60515United States of America Five-Year Limited Warranty Maple Chase Company warrants to the original contractor installer, or to the original consumer user, each new Robertshaw thermostat to be freefrom defects in materials and workman...