Raymarine ST80 - Manuals - manualsarea.com

Page 4 - Package Contents; Maxiview display head

ST80 Maxiview Operation and Setup 1 Package Contents 1. Maxiview display head 2. Thumb nuts (2) 3. Threaded fixing studs (2) 4. White sun cover 5. SeaTalk cable 6. Installation template 7. Operation manual 8. Warranty card 9. Operation cue card 10. Display head installation guide

Page 5 - Contents

ST80 Maxiview Operation and Setup 2 Contents Chapter 1: Introduction ............................................................. 7 Quick Reference Guide ............................................... 7 Chapter 2: Operation ............................................................... 10 2.1 Gen...

Page 10 - Chapter 1: Introduction; SPEED; Quick Reference Guide

ST80 Maxiview Operation and Setup 7 Chapter 1: Introduction D1580-1 maxiview SPEED KNOTS The Maxiview is a large-screen LCD repeater capable of displayingsingle or multiple lines of alphanumeric SeaTalk data. With a display area measuring 126 x 70mm (5 x 2.7in), theMaxiview provides a clear and unam...

Page 12 - Maximum Speed & Minimum Depth

ST80 Maxiview Operation and Setup 9 SPEED CHAPTER SPEED SPEED OVER GROUND VMG TO WIND LOG & TRIP CHAPTERS PAGES AVERAGE SPEED MAXIMUM SPEED NP NAVIGATE CHAPTER TIMERS CHAPTER RACE TIMER MULTILINE CHAPTER UP TO 8 USER DEFINED PAGES POSITION COGBTW CROSS TRACKERROR VMG TO WAYPOINT WAYPOINT DATA DA...

Page 13 - Operating the Maxiview using the Remote Keypad; • The keypad beeps once every time a key is pressed.; Gaining Control of the Maxiview; • In order to make changes to the Maxiview displays, you must gain

ST80 Maxiview Operation and Setup 10 Chapter 2: Operation 2.1 General The Maxiview operates around a chapter and page principle –chapters are independent sections: speed, depth, wind, etc., andpages data related to that chapter. When the Maxiview is powered up for the first time, the unitdefaults to...

Page 14 - Boat Speed Page; This page displays your actual boat speed.; SPEED KNOTS

ST80 Maxiview Operation and Setup 11 2.2 Speed Chapter Boat Speed Page This page displays your actual boat speed. D2469-1 maxiview remote SPEED KNOTS 10.5 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous pag...

Page 15 - This page displays your current speed over the ground from GPS.; SOG; VMG WIND

ST80 Maxiview Operation and Setup 12 Speed Over Ground (SOG) Page This page displays your current speed over the ground from GPS. D2470-1 maxiview remote SOG 6.5 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previ...

Page 16 - NM

ST80 Maxiview Operation and Setup 13 Log/Trip Page The Log/Trip page displays the total distance logged and a list oftrips and their current status. D2472-1 maxiview remote LOG/ TRIP LOG TRIP 1 OFF TRIP 2 OFF TRIP 3 ON TRIP 4 OFF TRIP 5 ON Press momentarily to advance to the next chapter. Press mome...

Page 17 - Average Speed; Maximum Speed Page; KNOTS; • The display flashes for 4 seconds when the maximum speed is reset.

ST80 Maxiview Operation and Setup 14 Average Speed This page displays the average boat speed for your current journey. D2473-1 maxiview remote SPEED AVG 8.0 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous p...

Page 18 - Depth Page; The depth page displays the current depth available on SeaTalk.; DEPTH FEET

ST80 Maxiview Operation and Setup 15 2.3 Depth Chapter Depth Page The depth page displays the current depth available on SeaTalk. D2475-1 maxiview remote DEPTH FEET Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the pr...

Page 19 - Minimum Depth Page; FT; FT

ST80 Maxiview Operation and Setup 16 Minimum Depth Page D2476-1 maxiview remote DEPTH MIN 9.2 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. FT Press and hold these keys for 4 seconds to reset the mi...

Page 20 - Apparent Wind Speed page; s STBD

ST80 Maxiview Operation and Setup 17 2.4 Wind Chapter Apparent Wind Speed page D2478-1 maxiview remote WIND APP 20.0 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. KNOTS • The units can be : KNOTS or...

Page 21 - True Wind Speed Page (Relative to the Vessel); • This page is not available in POWER mode.; PORT; • The direction indicator is displayed as PORT or STBD.

ST80 Maxiview Operation and Setup 18 True Wind Speed Page (Relative to the Vessel) D2480-1 maxiview remote 8.5 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. KNOTS • The true wind units can be either...

Page 22 - True Wind Angle (Referenced to the Compass); WNW; Heading Page; TRUE; • The heading can be true or magnetic.

ST80 Maxiview Operation and Setup 19 True Wind Angle (Referenced to the Compass) D2482-1 maxiview remote 296 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. WNW M • This page is not available in POWER...

Page 23 - Steering Page; UNLOCKED; This page displays your true or magnetic course over the ground.; • Whether the course is true or magnetic is dependant on the units

ST80 Maxiview Operation and Setup 20 Steering Page The steering page displays the current compass heading (unlockedmode) or the locked compass heading (locked mode). Note: For a detailed description of locked mode, please refer to aMasterview handbook. D2484-1 maxiview remote STEER 136 Press momenta...

Page 24 - This page shows the magnetic or true bearing to a target waypoint.; Tack Course Page

ST80 Maxiview Operation and Setup 21 Bearing to Waypoint (BTW) Page This page shows the magnetic or true bearing to a target waypoint. D2486-1 maxiview remote BTW 276 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the ...

Page 25 - Position Page

ST80 Maxiview Operation and Setup 22 2.6 Navigate Chapter Position Page D2488-1 maxiview remote POSITION 050 49.10 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. N-E 002 49.10 • If position data is n...

Page 26 - Cross Track Error; • The arrows indicate the direction to steer to correct any error.; Velocity Made Good (VMG) to Waypoint Page

ST80 Maxiview Operation and Setup 23 Cross Track Error The cross track error (XTE) page shows how far, in nautical miles(NM), statute miles (SM) or kilometres (KM), your vessel is from aplanned route. D2490-1 maxiview remote XTE 0.34 Press momentarily to advance to the next chapter. Press momentaril...

Page 27 - Waypoint Data Page; DTW; • The distance to waypoint can be nautical miles (NM), statute miles

ST80 Maxiview Operation and Setup 24 Waypoint Data Page This page displays any cross track error, the distance to a targetwaypoint (DTW), estimated time to arrival (ETA) and waypointnumber. D2492-1 maxiview remote Press momentarily to advance to the next chapter. Press momentarily to advance to the ...

Page 28 - TIDE; the Masterview handbook for details.

ST80 Maxiview Operation and Setup 25 Date/Time/Tide Page This page displays the speed and direction of the tide and the localtime. D2493-1 maxiview remote Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous pag...

Page 29 - Race Timer Chapter; • The display shows minutes and seconds only.; • In race mode the timer shows the elapsed time in minutes and

ST80 Maxiview Operation and Setup 26 2.7 Race Timer Chapter Race Start Page This page duplicates race timer data from a Masterview instrument.There are just two operating modes: STOPPED and COUNTINGDOWN/UP. D2494-1 maxiview remote RACE START 10:00 Press momentarily to advance to the next chapter. • ...

Page 30 - FEET

ST80 Maxiview Operation and Setup 27 2.8 Multi-Line Multi-line chapters consist of up to 8 pages of user-defined pages. D2496-1 maxiview remote DEPTH 7.2 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page...

Page 32 - List of Multi-line Selections

ST80 Maxiview Operation and Setup 29 List of Multi-line Selections The lines of data that can be selected are as follows: Line Data Line Data 1 Speed 17 Steer 2 Speed over ground 18 Course over ground 3 Velocity made good to wind 19 Tack course 4 Velocity made good over ground 20 Vessel latitude 5 L...

Page 33 - Multi-line Factory Defaults

ST80 Maxiview Operation and Setup 30 Multi-line Factory Defaults The factory defaults for the Multi-line pages are: Page Line Content 1 1 Speed 2 Average speed 3 Speed over ground 4 Velocity made good to waypoint 2 1 Depth 2 Water temperature 3 1 Heading 2 Steer 3 Course over ground 4 Bearing to way...

Page 34 - the mode is changed to system.

ST80 Maxiview Operation and Setup 31 2.9 Illumination There are two modes: local and system. Each of these modes hasfour possible settings: level 3 (brightest), level 2, level 1 and off. Local illumination is used to adjust the lighting of individualdisplay heads — adjustments will not affect other ...

Page 35 - Resetting the Contrast; WARNING; SPEED CHAPTER; Man Overboard and Alarms; MOB; DR

ST80 Maxiview Operation and Setup 32 Resetting the Contrast The display contrast can, during local or system illuminationadjustment, be reset to the factory default by pressing the page keyfor 1 second. 2.10 Data Lost If a chapter that is dependent on a given quantity, e.g., speed, wind,depth, and t...

Page 36 - POS; MAN

ST80 Maxiview Operation and Setup 33 • The dead reckoned screen is displayed providing data is available. • Fields where data is not available appear as dashes. • The elapsed time is displayed in minutes and seconds. • The displayed bearing and range is to the man in the water. Lat/Lon MOB D2543-1 m...

Page 37 - MOB Audible Alarm

ST80 Maxiview Operation and Setup 34 MOB Audible Alarm During an MOB condition, an audible alarm beeps 3 times everythirty seconds. Alarms The Maxiview can be set to respond to all the alarms in thefollowing table or, alternatively, only those identified as specific. Alarm Pop-Up Displayed Response ...

Page 38 - received, the current alarm is replaced with the new alarm.; Audible Alarms; • High priority alarms will always override low priority alarms.

ST80 Maxiview Operation and Setup 35 The following table lists the alarm status once a silence/turn offkey- sequence is performed. Alarm Silenced Turned Off Shallow depth Yes No Deep depth No Yes Anchor Yes No True wind high speed No Yes True wind low speed No Yes True wind high angle No Yes True wi...

Page 39 - DEPTH f FEET; • “SET-UP OFF” replaces the above screen if user setup has been

36 ST80 Maxiview Operation & Setup Chapter 3: Setup This chapter describes how to set and adjust features in the setupmenu. These include display formats, response levels for controllingthe frequency of screen updates and the thresholds for trendindicators. 3.1 Entering Setup D2499-1 maxiview re...

Page 40 - Speed Chapter; Response Pages

ST80 Maxiview Operation & Setup 37 Speed Chapter The following screen is displayed for 2 seconds when entering speedsetup. The key sequences shown are only available during thisperiod. D2500-1 maxiview remote CHAP 1S FOR INSTRUMENT CHAPTER SPEED Press this key to advance to the next chapter. SET...

Page 41 - • The current boat speed/VMG to wind is always displayed.; Trend Indicator Thresholds; or

38 ST80 Maxiview Operation & Setup There are two response pages: speed and VMG to wind. Speedresponse covers boat speed, speed over ground, velocity made goodto waypoint and velocity made good over ground to waypoint. D2501-1 maxiview remote Press this key momentarily to advance to the next chap...

Page 43 - Display Format; The display format can be set to either 1 or 2 decimal places.; • Values are limited to 3 significant figures. Values over 9.99 with; Depth Chapter

40 ST80 Maxiview Operation & Setup Display Format The display format can be set to either 1 or 2 decimal places. D2503-1 maxiview remote Press this key momentarily to advance to the next chapter. X.X X.XX Press this key momentarily to advance to the next page. Press this key for 1 second to retu...

Page 44 - Depth Response

ST80 Maxiview Operation & Setup 41 Depth Response D2505-1 maxiview remote Press this key momentarily to advance to the next chapter. DEPTH FEET 20.5 RESPONSE S F 07 Press this key momentarily to advance to the next page. Press this key for 1 second to return to the previous page. Press these key...

Page 45 - Depth Display Format; Wind Chapter

42 ST80 Maxiview Operation & Setup Depth Display Format D2507-1 maxiview remote Press this key momentarily to advance to the next chapter. X X.X Press this key momentarily to advance to the next page. Press this key for 1 second to return to the previous page. Press these keys together momentari...

Page 46 - Wind Speed Response; Wind Angle Response

ST80 Maxiview Operation & Setup 43 Wind Speed Response D2509-1 maxiview remote Press this key momentarily to advance to the next chapter. WIND SPEED KNOTS 5.0 RESPONSE S F 07 Press this key momentarily to advance to the next page. Press this key for 1 second to return to the previous page. Press...

Page 47 - Multiline Chapter; MULTILINE

44 ST80 Maxiview Operation & Setup Display Format D2507-1 maxiview remote Press this key momentarily to advance to the next chapter. X X.X Press this key momentarily to advance to the next page. Press this key for 1 second to return to the previous page. Press these keys together momentarily to ...

Page 48 - Editing Rights; • Edit all allows you to edit chapters and pages. Edit pages allows

ST80 Maxiview Operation & Setup 45 Editing Rights The editing rights chapter allows you to control the level of multilinepage editing. The options are: edit all, edit pages and no editing. D2513-1 maxiview remote Press this key momentarily to advance to the next chapter. EDIT ALL EDIT PAGES NO E...

Page 49 - INSTRUMENT; Transducers Page; This page lists all the transducers connected to SeaTalk.; • Detected transducers are identified by a

46 ST80 Maxiview Operation & Setup 3.2 Instrument Setup D2514-1 maxiview remote CHAP 1S FOR MULTILINE CHAPTER INSTRUMENT Press this key to advance to the next chapter. SET-UP Press this key for 1 second to return to the multiline chapter. Transducers Page This page lists all the transducers conn...

Page 50 - • If a selection has not been previously made, the SYSTEM option is

ST80 Maxiview Operation & Setup 47 Sail/Power/Custom Selection This page allows you to select whether chapters are custom selectionsor, alternatively, dictated by the sail or power boat settings. D2516-1 maxiview remote Press this key momentarily to advance to the next chapter. Press this key mo...

Page 51 - Custom; • Enabled chapters are identified by a

48 ST80 Maxiview Operation & Setup Custom This mode allows you to select any of the chapters from thefollowing list: No. Chapter No. Chapter 1 Speed 5 Navigate 2 Depth 6 Timers 3 Wind 7 Multiline 4 Heading D2517-1 maxiview remote Press this key momentarily to return to speed calibration chapter....

Page 52 - Contents Setup; • At least one page must be selected. The last page in a chapter cannot

ST80 Maxiview Operation & Setup 49 Contents Setup In custom setup, contents setup is used to select or de-select pageswithin the highlighted chapter. D2518-1 maxiview remote Press this key momentarily to return to the chapter setup page. Press these keys together momentarily to highlight the nex...

Page 53 - Title Control

50 ST80 Maxiview Operation & Setup Title Control This is used to turn the chapter title pages, displayed for 2 secondsupon entry to a chapter, ON or OFF. D2519-1 maxiview remote Press this key momentarily to return to speed calibration chapter. Press this key for 1 second to return to the sail/p...

Page 54 - Variation; • The maximum variation that can be entered is 30°.

ST80 Maxiview Operation & Setup 51 Variation This page is used to enter the local variation to the nearest wholedegree. D2520-1 maxiview remote Press this key momentarily to return to speed calibration chapter. Press this key for 1 second to return to the title control page. Press this key momen...

Page 55 - True/Magnetic Heading; any response to incoming true or magnetic data.

52 ST80 Maxiview Operation & Setup True/Magnetic Heading The true/magnetic heading page is used to select one of four options:local true, local magnetic, global true or global magnetic. D2531-1 maxiview remote Press this key momentarily to return to speed calibration chapter. Press this key for ...

Page 56 - Lamp Offset Adjustment; • Lamp adjustment is not available if the current setting is OFF.

ST80 Maxiview Operation & Setup 53 Lamp Offset Adjustment This feature allows you to adjust the brightness of individualillumination levels to obtain the best setting for a particular location. D2532-1 maxiview remote LAMP ADJSUTMENT LEVEL 2 MIN MAX 32 Press this key momentarily to advance to co...

Page 57 - Contrast Adjustment

54 ST80 Maxiview Operation & Setup Contrast Adjustment D2533-1 maxiview remote CONTRAST ADJUSTMENT MIN MAX 07 Press this key momentarily to advance to LCD inversion control page. Press this key for 1 second to return to the previous page. Press these keys together momentarily to decrease value b...

Page 58 - LCD Inversion; LCD inversion allows you to change the display to:

ST80 Maxiview Operation & Setup 55 LCD Inversion LCD inversion allows you to change the display to: • display black numbers and characters on a light background • or display light numbers and characters on a black background D2534-1 maxiview remote Press this key momentarily to return to speed s...

Page 59 - Alarm Control

56 ST80 Maxiview Operation & Setup Alarm Control This page is used to define whether all or just specific alarms will berecognised by the Maxiview. D2535-1 maxiview remote Press this key momentarily to return to speed setup. Press this key for 1 second to return to LCD inversion. Press this key ...

Page 60 - Quitting User Setup; EXIT

ST80 Maxiview Operation & Setup 57 3.3 Quitting User Setup To quit setup, simply press the Chapter and Page keys togethermomentarily to display the following screen. D2539-1 maxiview remote EXIT If cancel is selected, press this key momentarily to exit without saving. If store is selected, press...

Page 61 - Chapter 4: CodeLock Security; Master’s

58 ST80 Maxiview Operation & Setup Chapter 4: CodeLock Security 4.1 What is CodeLock? • CodeLock is a personal four digit security code designed to protect your valuable equipment against theft. • CodeLock does not have to be switched on, but it’s there if you decide that you need it. • When Cod...

Page 62 - Analogue Display Heads

ST80 Maxiview Operation & Setup 59 4.2 Analogue Display Heads Automatic CodeLock Systems In an automatically transmitted CodeLock system, the Maxiviewreads the code number and starts-up automatically without any userinput. Manual CodeLock System In a manually transmitted CodeLock system, the cod...

Page 63 - Chapter 5: Problem Solving; Display is blank

60 ST80 Maxiview Operation & Setup Chapter 5: Problem Solving 5.1 Problem Solving Display is blank • Make sure that the power supply is connected. • Check the fuse or circuit breaker. • Make sure that the SeaTalk cables are not damaged. • Check the contrast and illumination settings • Faulty LCD...

Page 64 - Chapter 6: EMC and Servicing Guidelines; Important information; • At least 1m (3 feet) from any equipment transmitting or cables

ST80 Maxiview Operation & Setup 61 Chapter 6: EMC and Servicing Guidelines 6.1 Important information All Autohelm equipment and accessories are designed to the bestindustry standards for use in the leisure marine environment. Their design and manufacture conforms to the appropriateElectromagneti...

Page 65 - Check Before Going to Sea; is not affected by radio transmissions, engine starting etc.; Servicing and Safety; • Autohelm equipment should be serviced only by authorised

62 ST80 Maxiview Operation & Setup 6.3 Check Before Going to Sea • Always check the installation before going to sea to make sure that it is not affected by radio transmissions, engine starting etc. • In some installations, it may not be possible to prevent the equipment from being affected by e...

Page 66 - Chapter 7: Specification; Operating temperature:

ST80 Maxiview Operation & Setup 63 Chapter 7: Specification Dimensions: 110 x 114.5 x 18.25mm (4.33 x4.5 x 0.71in) Power supply: 10 to 16 V DC Current consumption: 50 mA with illumination off250mA with illumination full on Operating temperature: -10 to +70°C (14°F to 158°F) Illumination: 3 level...

Page 68 - Index

ST80 Maxiview Operation & Setup 65 Index A Alarm Control 56 Alarms 34 Apparent Wind Angle Page 17 Apparent Wind Speed page 17 Audible Alarms 35 Automatic CodeLock Systems 59 Average Speed 14 B Bearing to Waypoint (BTW) Page 21 Boat Speed Page 11 C CodeLock Security 58 Contents Setup 49 Contrast ...