Raymarine GPS Plotter - Manual

Prelim Pages v Figure ii: WAAS Coverage Map Coverage Outside of North America Europe and Asia are developing similar systems to WAAS called EGNOS and MSAS respectively. Combined with WAAS, these systems will provide global satellite based differential GPS augmentation into the future. EGNOS is curre...

vi Raynav 300 GPS Plotter Preface This handbook covers the Raynav 300 GPS Plotter manufactured by Raymarine. It contains important information on the installation and operation of your new equipment. In order to obtain the best results in operation and performance, please read this handbook thorough...

Prelim Pages vii Contents - Raynav 300 Plotter SAFETY NOTICES......................................................................... iiiWAAS Satellite Differential GPS ............................................. iii Availability of the WAAS System in North America ivExtended Offshore Coverage iv...

Chapter 1: Overview 1-1 Chapter 1: Overview 1.1 Introduction This handbook describes the Raynav 300 GPS Plotter. Note: Many illustrations in this handbook show example screens. The screen you see on your display depends on your system configuration and set up options, so it may differ from the illus...

1-2 Raynav 300 GPS Plotter 1.2 Features General The Raynav 300 GPS Plotter has a built-in GPS that provides the following navigational signals: • Satellite Differential GPS (eg, WAAS). • Ground based Differential GPS, when used with an additional RTCM beacon receiver. • Standard GPS. These are liste...

Chapter 1: Overview 1-3 Those modes containing more than one page of data provide additional soft keys giving access to the sub-sets of data within each group, each cycled through with the associated soft key. 1.3 The Plotter Display When a position fix has been established, your vessel’s position, ...

1-4 Raynav 300 GPS Plotter Plotter Functions Display Functions The Raynav 300 GPS Plotter includes the following functions: • Place, Move, Erase and Edit a Waypoint • Goto Waypoint or Cursor • Create, Save, Name, Edit and Follow a Route • Review Route and Waypoint Lists • Display vessel’s track; Sav...

Chapter 1: Overview 1-5 1.4 Operating Controls Operation utilizes a number of buttons and on-screen controls. These include: • A trackpad providing up, down, left, right and diagonal control of an on-screen cursor. • Eight dedicated (labelled) control keys. • Four soft keys with labels displayed on ...

1-6 Raynav 300 GPS Plotter The cursor is used to: • Select a position on the screen. • Select and, if valid, move an item, e.g. a waypoint, on the screen. • Select an area of the screen to zoom into. • Pan the display. Moving the Cursor Press the corresponding edge of the trackpad to move the cursor...

Chapter 1: Overview 1-7 Dedicated Keys The dedicated keys: DISPLAY, MARK, RANGE, ALARMS, ENTER, CLEAR, MENU and POWER have fixed functions. Some keys can be used in two ways: • Press: Press the key momentarily and then release it. This method is used for most key operations. • Press and hold: Press ...

1-8 Raynav 300 GPS Plotter Pop-Up Menus Pop-up menus usually provide set up options. When a pop-up menu is on-screen, a set of associated soft keys is also displayed as shown in Figure 1-3 . Figure 1-3: Typical Pop-up Menu Use the trackpad to select an option from the menu, then use the appropriate ...

Chapter 2: Getting Started 2-1 Chapter 2: Getting Started 2.1 Introduction This chapter provides information, instructions and a simple familiarization exercise in using the display. Operating information is detailed in Chapter 3 . Conventions Used Throughout this handbook, the dedicated (labelled) ...

2-2 Raynav 300 GPS Plotter Figure 2-1: GPS Status Screen The GPS Status screen is displayed until a satellite fix has been acquired. When satellite acquisition is complete, the READY FOR NAVIGATION pop-up box displays for two seconds. To proceed whilst satellite acquisition continues, press the CLEA...

Chapter 2: Getting Started 2-3 zero the display and key backlights extinguish. If the POWER key is released within this period, power-down is cancelled. Changing the Lighting and Contrast You can change the level of backlighting and contrast for the screen and keys. The key backlighting always retai...

2-6 Raynav 300 GPS Plotter 2.4 Plotter Display Control Functions You will normally operate the GPS Plotter with the display showing one of the Navigation Data pages. The range of pages is listed in Selecting the Display Mode on page 2-4 and illustrated in Figure 2-5 . The complete range of pages is ...

Chapter 2: Getting Started 2-7 ➤ To release the cursor from homed mode, use the trackpad to move the cursor away from the vessel’s current position. The status bar shows the current cursor position, bearing and range. The cursor no longer moves with the vessel and no redraw occurs if the vessel move...

2-8 Raynav 300 GPS Plotter Figure 2-6: Status Bar ➤ To change the scale rapidly, press and hold top or bottom of the RANGE key. The distance indicator at the left-hand side of the status bar is updated whenever you change the display scale. ➤ To zoom in to a larger-scale (more detailed) display: 1. ...

Chapter 2: Getting Started 2-9 Switching Grid On/off The Plotter display can be set to show grid lines of latitude and longitude which can help determine position. ➤ To turn the grid on or off: 1. Press the SCREEN default soft key. 2. Press the CHRT GRID soft key to toggle the setting ON and OFF . 3...

Chapter 3: Operation 3-1 Chapter 3: Operation 3.1 Introduction This chapter explains how to navigate with the Raynav 300 GPS Plotter. It covers the following topics: • Controlling waypoints, including placing, moving, editing and delet-ing waypoints. • Changing the display mode.• Using a range of da...

3-2 Raynav 300 GPS Plotter The modes that contain more than one page of data provide additional soft keys which cycle through the pages. The highlighted soft key indicates the screen mode currently displayed. Note: Press the DISPLAY key for at least two seconds in any display mode to return to the G...

Chapter 3: Operation 3-3 GPS/Waypoint Data GPS Data The GPS Data display comprises four text data pages, selected in turn by the GPS DATA soft key. These pages are shown in Figure 3-1 to Figure 3-4 . Figure 3-1: GPS Data Page #1 Figure 3-2: GPS Data Page #2 D4936-2 WPT BRG 320° M 0.55 nm 050° M 12.0...

Chapter 3: Operation 3-5 Waypoint Data The Waypoint Data display comprises three data pages, selected in turn by the WPT DATA soft key. These pages are shown in Figure 3-5 to Figure 3-7 : Figure 3-5: Waypoint Data #1 Figure 3-6: Waypoint Data #2 D4940-2 XTE 0.06 nm 01 h: 00 m 050° M TTG COG SOG ROUT...

3-6 Raynav 300 GPS Plotter Figure 3-7: Waypoint Data #3 Boat/Environment Data Boat Data The Boat Data display comprises three data pages, selected in turn by the BOAT DATA soft key. These pages are shown in Figure 3-8 to Figure 3-10 : Figure 3-8: Boat Data #1 D4942-2 OWN POS 050° M WPT POS COG SOG R...

Chapter 3: Operation 3-7 Figure 3-9: Boat Data #2 Figure 3-10: Boat Data #3 D4944-2 WPT BRG 320° M 0.55 nm 050° M 12.0 kts WPT RNG COG SOG ROUTE GOTO BOAT DATA ENVIROMNT SD-FIX STEER STARBOARD WPT 004 DEPTH 12.5 M TEMP 11° C D4945-2 PILOT AUTO 050° M 0.05 nm RUDDER COG XTE ROUTE GOTO BOAT DATA ENVIR...

3-8 Raynav 300 GPS Plotter Environment Data The Environment Data display comprises two data pages, selected in turn by the ENVIRONMT soft key. These pages are shown in Figure 3-11 and Figure 3-12 . Figure 3-11: Environment Data #1 Figure 3-12: Environment Data #2 D4946-2 WIND SSW 7 050° M 320° M RUD...

Chapter 3: Operation 3-9 CDI/BDI Data The Course Deviation Indicator (CDI) / Bearing Deviation Indicator (BDI) display comprises two data pages, selected alternately by the CDI and BDI soft keys. These pages are shown in Figure 3-13 and Figure 3-14 : CDI Data The CDI display shows Cross Track Error ...

3-10 Raynav 300 GPS Plotter of distance to destination and Velocity Made Good (VMG) towards destination. Figure 3-14: BDI Display The line to the waypoint symbol is shown at an angle equal to the difference between the COG and the Bearing to Waypoint to a maximum of ± 15°. The waypoint symbol is the...

Chapter 3: Operation 3-11 Data Log The GPS Plotter can be set to log passage data every 30 minutes. Up to 48 log entries are held. When 48 entries have been saved, the first entries start being overwritten. If the number of log entries exceeds the table size, use the trackpad up/down to scroll the l...

3-12 Raynav 300 GPS Plotter 3.3 Working with Waypoints Introduction You can place up to 998 waypoints on the GPS Plotter. A waypoint is a position entered on the display as a reference or destination point. All waypoints placed on the GPS Plotter are stored in a waypoint database list which includes...

Chapter 3: Operation 3-13 Placing a Waypoint ➤ To access the Place Waypoint soft keys, press MARK ; the Place Waypoint soft keys are displayed as shown in Figure 3-17 : Figure 3-17: Waypoint Soft Keys ➤ To place a waypoint at the cursor (plotter screen) or the vessel’s current position: 1. Press eit...

3-14 Raynav 300 GPS Plotter 2. Press the MAKE NEW WAYPOINT soft key; the New Waypoint screen is displayed, together with its associated soft keys, see Figure 3-19 . Figure 3-19: New Waypoint Screen 3. The new waypoint is listed at the vessel’s current position or, if not available, the cursor’s curr...

Chapter 3: Operation 3-17 Selecting a Waypoint Selecting a waypoint from the Waypoint List allows you to GOTO and EDIT (symbol, name, position, erase) the waypoint. The Waypoint List also provides options to make a new waypoint and transfer waypoints. Positioning the cursor over a waypoint selects t...

3-18 Raynav 300 GPS Plotter 2. To remove the Waypoint List and return to the default soft key dis- play, press CLEAR twice. ➤ To display the Waypoint Data Box: 1. Move the cursor over the waypoint. • The Waypoint Data Box is displayed which indicates waypoint number/name, bearing and range (or lat/l...

Chapter 3: Operation 3-19 The NAME WAYPOINT window is displayed. 5. Use the trackpad to enter or edit the name: • Use the trackpad left/right to move the cursor to the character to be changed. • Use the trackpad top/bottom to scroll through the characters. 6. When name editing is complete, press ENT...

3-20 Raynav 300 GPS Plotter 3. If the the deleted waypoint was the only waypoint in the list, the default soft keys are displayed, otherwise, press CLEAR three times to return to the default soft keys. ➤ To delete a waypoint using the cursor: 1. Move the cursor over the waypoint until the letters WP...

Chapter 3: Operation 3-21 3.4 Working with Routes A route is made up of a series of waypoints (maximum 50). To make a route you place a series of waypoints and/or use existing ones. When a route is created, it becomes the current route and is displayed on screen. The current route is maintained when...

3-22 Raynav 300 GPS Plotter Creating a New Route Note: If there is a current route, it is cleared when MAKE ROUTE is select- ed . If following the current route you are prompted to STOP FOLLOW . Press the YES soft key to continue, or NO to abandon route creation. If the route has not been saved you ...

Chapter 3: Operation 3-25 Saving the Current Route You can save up to 20 named routes in the Route Database List. These routes can then be re-displayed and followed at a later date. When you save the route, all new waypoints are saved in the Waypoint List. Note: When a change to this route is attemp...

3-26 Raynav 300 GPS Plotter Displaying Route Information The following route information can be displayed: • Full route details, using the soft keys. • Route leg or waypoint information, using the context-sensitive cur-sor. Full Route Details ➤ To display information about any route in the database:...

3-28 Raynav 300 GPS Plotter Route Leg and Waypoint Information ➤ To display information about a route leg, move the cursor over the leg until the letters RTE appear. The Route Leg data box is displayed, together with the Follow Route soft keys as shown in Figure 3-34 . Figure 3-34: Route Leg Data Bo...

Chapter 3: Operation 3-29 Press the CLEAR ROUTE soft key to clear the route. or... 2. Press the ROUTE default soft key. The Route soft keys are displayed as shown in Figure 3-29 : Press the CLEAR ROUTE soft key to clear the route. or... 3. If following the current route, the STOP FOLLOW soft keys ar...

3-30 Raynav 300 GPS Plotter ➤ To select a route as the current route: 1. From plotter mode, press the ROUTE soft key, followed by MORE , then ROUTE LIST . The Route List is displayed with the selected route high- lighted, see Figure 3-32 . Note: In any mode other than plotter mode, the ROUTE LIST so...

Chapter 3: Operation 3-31 Note: Apart from Moving a Waypoint used in other route(s), any chang- es made to the route affect the current route only. The current route must always be Saved in order to keep the changes. Inserting a Waypoint into a Route The context-sensitive cursor can be used to inser...

3-32 Raynav 300 GPS Plotter Removing a Waypoint from within the Route ➤ To remove a waypoint from within the current route: 1. Move the cursor over the required waypoint until the letters WPT appear; the waypoint soft keys are displayed. 2. Press the REMOVE WAYPOINT soft key. The waypoint is removed...

Chapter 3: Operation 3-33 intended track, from your start point or previous waypoint, to the target waypoint. This section describes the following: • Go to an individual target point (an existing waypoint or the cursor). • Follow a route either forward, or reversed. • Joining a route at a selected w...

3-34 Raynav 300 GPS Plotter 3. To return to the default soft key display, move the cursor away from the waypoint or press CLEAR . ➤ To navigate directly to the cursor position: 1. Use the trackpad to position the cursor as required.2. Press the GOTO default soft key, followed by GOTO CURSOR . If nav...

Chapter 3: Operation 3-35 Figure 3-39: Follow Route Soft Keys ➤ To follow the current route in reverse using the soft keys: 1. Reverse the route as described in Reversing the Route on page 3-32 . 2. Press the GOTO default soft key; the Goto/Follow soft keys are dis- played. 3. Press the FOLLOW ROUTE...

3-36 Raynav 300 GPS Plotter ➤ To advance to a waypoint: 1. Press the GOTO default soft key to display the Goto/Follow soft keys. 2. Press the WAYPOINT ADVANCE soft key. The current leg of the route is abandoned and the next waypoint becomes the target. The display is updated to show the new route le...

Chapter 3: Operation 3-37 • The distance to the target point is less than that specified for the Arrival alarm. • Your vessel reaches the closest point of approach to the target (defined by an imaginary circle around the waypoint). ➤ To cancel the Arrival alarm and go towards the next waypoint in th...

3-38 Raynav 300 GPS Plotter When this option is selected, any waypoints received on SeaTalk or NMEA are transferred and appended, one-by-one, to the Waypoint List. Routes received on NMEA are appended to the Route List.You can use this function to add waypoints from a PC connected via NMEA. • You ca...

Chapter 3: Operation 3-39 While Track is on, it is recorded in memory as the Current Track and is retained following a POWER OFF/ON . You specify the interval at which track points are created and a line is drawn on-screen between each point. The current track remains on-screen until you clear the t...

Chapter 3: Operation 3-41 3. Press the MORE... soft key to display the second level Track soft keys as shown in Figure 3-43 . Figure 3-43: Second Level Track Soft Keys 4. Press the appropriate TRACK INTERVAL up/down soft key to set an appropriate TIME or DISTANCE interval. 5. Press MORE to return to...

3-42 Raynav 300 GPS Plotter 2. Check the route and, in particular, that the route deviation from the original, given in the warning box, is within navigable limits. Managing Tracks It is a staightforward task to set up a Current Track which is retained even if you switch off your display unit. In ad...

Chapter 3: Operation 3-43 Naming, Erasing and Showing a Track ➤ To name an existing track, erase a track or show a track: 1. Press the TRACK LIST soft key; the Track List is displayed. The highlight indicates the selected track. 2. Using the trackpad top/bottom, select the required track and press t...

3-44 Raynav 300 GPS Plotter 3.8 Man Overboard (MOB) If a person or object is lost overboard, use the Man Overboard (MOB) function to return to the location immediately. Note: To obtain an MOB position, you need either of the following: • Position data from the GPS antenna. • Heading and speed data, ...

Chapter 3: Operation 3-45 • Replaces all current waypoint data with MOB data. ➤ To cancel the MOB, press and hold the MARK key for 2 seconds. The chart is re-drawn at its previous scale, and the MOB symbol and data box are removed. Note: The MOB procedure can also be initiated or cancelled remotely-...

3-46 Raynav 300 GPS Plotter Setting Alarms and Timers ➤ To set up an alarm or timer: 1. Press the ALARMS key. The Alarms Set Up list is displayed, showing the current settings as shown in Figure 3-46 . Figure 3-46: Alarms Set Up Menu 2. Use the trackpad up/down to navigate through the list. As each ...

Chapter 3: Operation 3-47 3.10 Cursor Echo In a plotter display, or in a system with any plotter display connected via Seatalk, you can set the display to enable cursor transfer. Cursor echo is accessed from the Set Up Menu and enables the display of a plotter cursor on other equipment, or another e...

Chapter 4: Setting Up the GPS Plotter 4-1 Chapter 4: Setting Up the GPS Plotter 4.1 Introduction When you have installed your system and are familiar with its basic operation, you may wish to set it up to operate according to your requirements and display information according to your preferences. T...

4-2 Raynav 300 GPS Plotter As each line is highlighted, the soft keys are updated to show the set-tings available. • For parameters that have a numeric value, or more than four possible settings, a scroll list is displayed above two of the soft keys. • Some parameters are controlled by an adjustable...

4-4 Raynav 300 GPS Plotter Bearing Mode This is the mode (magnetic or true) of all the bearing and heading data displayed as indicated in the status bar. Cursor Reference The mode of the bearing data displayed for the cursor readout. The bearing information can be displayed in either of two forms: •...

4-6 Raynav 300 GPS Plotter Auto Mode If Auto mode is selected, the value of variation is obtained automatically, normally from received data. The variation value that is used depends on the data available, and is selected in the following order of priority: 1. Variation value from the same source as...

Chapter 4: Setting Up the GPS Plotter 4-7 Press the CURSOR ECHO soft key to display the cursor transfer soft keys. The following options can be toggled ON or OFF : • Radar Cursor In: displays the cursor from another radar on the plot- ter display or chart window (default - OFF ). • Chart Cursor In: ...

4-8 Raynav 300 GPS Plotter NMEA Input Select the NMEA input setting as appropriate. This can be set to either NMEA or RTCM . RTCM input is 4800 baud only. Language Select the language in which you wish information to be displayed. The selected language will be used for screen text, labels, menus and...

Chapter 4: Setting Up the GPS Plotter 4-9 Chart Orientation The plotter orientation is normally North Up, but can be changed to Course Up or Head Up if heading data is available. The orientation modes give the following displays: • North Up: The screen is displayed with north upwards. As you change ...

4-10 Raynav 300 GPS Plotter Default Waypoint Symbol This setting provides a selection of symbols for the default waypoint display. Vectors Heading, Tide and Course Over Ground vectors can be displayed as a line from your vessel. The length of the vector is determined by your choice of SOG and the ti...

Chapter 4: Setting Up the GPS Plotter 4-11 Figure 4-2: GPS Status Screen The GPS Navigation Status screen provides, for each tracked satellite, the satellite number, a graphical signal strength bar and its current usage status. Data for up to 12 satellites are shown. Positional accuracy is dependent...

4-12 Raynav 300 GPS Plotter D-GPS Set Up The D-GPS SET UP function is only available when a Differential GPS receiver is connected and the unit is set as a GPS Source repeater (see GPS Source on page 4-7 ). It provides the ability to set up an external Differential GPS, either automatically (default...

Chapter 4: Setting Up the GPS Plotter 4-13 Beacon Frequency Both the menu item and associated soft keys show the currently used differential beacon’s frequency in kHz. In AUTO mode, this is the frequency received from the beacon receiver and the soft keys are disabled and grayed out. In MAN mode, th...

Chapter 5: Installation 5-1 Chapter 5: Installation 5.1 Introduction This chapter provides instructions to assist in planning the installation of the Raynav 300 GPS Plotter aboard your vessel. Note: If you wish to practice using the Raynav 300 GPS Plotter before installation, you can connect it, via...

5-2 Raynav 300 GPS Plotter • Raymarine specified cables are used. Cutting and rejoining these cables can compromise EMC performance and must be avoided unless doing so is detailed in the installation manual. • If a suppression ferrite is attached to a cable, this ferrite should not be removed. If th...

Chapter 5: Installation 5-3 5.2 Unpacking and Inspecting the Components Unpack your Raynav 300 GPS Plotter carefully. Retain the carton and packing materials in the event that you need to return the unit for service: System Parts and Accessories Items Missing? If any one (or more) of the above items...

5-4 Raynav 300 GPS Plotter 5.3 GPS Antenna Installation The GPS Antenna is designed to receive the signals emitted from the satellites in a direct path. Ideally, the unit should be mounted horizontally in a location that is open and clear of any masts or other structures that could block line-of-sig...

5-6 Raynav 300 GPS Plotter Pole Mounting ➤ Refer to Figure 5-3 : 1. Screw the pole mount base to a suitable pole or rail mount bracket, having an industry standard 1inch 14TPI thread, until secure. 2. Pass the cable through the centre hole of the pole mount base (A) or insert the cable into the side...

Chapter 5: Installation 5-7 5.4 Plotter Installation The display unit can be mounted using the trunnion (yoke) bracket, or panel mounted using the optional Panel Mounting Kit. When planning the installation of your Raynav 300, the following points should be considered: • Convenience: The unit should...

Chapter 5: Installation 5-9 4. Secure the gasket to the rear of the unit: Remove the protective paper from the adhesive side of the gasket (this is the side that is to be affixed to the unit) then press the gasket onto the rear case, covering the screws. 5. Fit the unit to the trunnion, adjust the d...

5-10 Raynav 300 GPS Plotter 12. Screw the studs into the vacant holes at the rear of the unit, hand tight only. 13. Slide a spacer ferrule onto each stud.14. Secure the unit with the thumb nuts, hand tight only. Figure 5-5: Panel Mounting 5.5 Connecting to Other Equipment The unit transmits navigati...

Chapter 5: Installation 5-11 5.6 Cable Running Introduction The minimum requirements are a power cable and a connection from the associated GPS Antenna. Additional cables will be required if you are connecting to other equipment. Consider the following points before installing the system cables: • A...

5-12 Raynav 300 GPS Plotter Antenna Connector The ANTENNA connector provides power and RF connection to the associated GPS Antenna. CAUTION: Do not connect/disconnect the GPS Antenna from the display unit whilst power is applied. Such action could cause irreparable damage. ➤ Connect the antenna usin...

Chapter 5: Installation 5-13 If a longer power cable run is required, use the supplied power cable to connect to the unit, then use a suitable connector block to connect the free end to the extension cable. The supplied power cable has a cross-section of 2.0mm 2 (15 AWG). Longer power cable runs may...

5-14 Raynav 300 GPS Plotter ➤ Connect the power supply using the standard power cable supplied: 1. Connect the moulded power plug to the PWR/NMEA connector on the rear of the Plotter. Run the free end back to the vessel’s distribu-tion panel or, if insufficient cable length, to a junction box. 2. Cu...

Chapter 5: Installation 5-15 Initial Switch On To switch on the plotter: 1. Press and hold the POWER key until the unit beeps. 2. If necessary, adjust the lighting and contrast (see Chapter 2 ). 3. If required, change the default language settings as follows: i. Press the MENU key to display the set...

Chapter 6: Maintenance & Fault Finding 6-1 Chapter 6: Maintenance & Fault Finding This chapter provides information on routine maintenance and on possible causes of problems you may experience with your Raynav 300 GPS Plotter. 6.1 Maintenance WARNING: The plotter contains specialized circuit...

6-2 Raynav 300 GPS Plotter • Always report any EMC-related problem to your nearest Raymarine dealer. We use such information to improve our quality standards. • In some installations, it may not be possible to prevent the equipment from being affected by external influences. In general this will not...

Appendix A: Technical Summary A-1 Appendix A: Technical Summary Feature Description CE Conforms to 89/336/EEC(EMC), EN60945:1997 Y2K Compliant Size 7.7in (195mm) x 4.33in (110mm) x 3.9in (99mm), excluding trunnion Weight 1.65 lb. (0.75 kg) Environmental Waterproofing To CFR46; suitable for external ...

Appendix B: SeaTalk and NMEA Data B-1 Appendix B: SeaTalk and NMEA Data The following table defines the data received on the NMEA/SeaTalk ports. Data sources are listed in order of priority unless otherwise indicated. Data Received Source Vessel Position (LAT/LON) SeaTalk, GGA, RMC, RMA, GLL Speed a...

Appendix C: List of Abbreviations C-1 Appendix C: List of Abbreviations Abbreviation Meaning BDI Bearing Deviation Indicator BTW Bearing To Waypoint CDI Course Deviation Indicator COG Course Over Ground. The actual direction of your vessel’s movement over the ground dGPS Differential Global Position...

This equipment uses certain elements of software supplied to Raymarine by SiRF Tech-nology Inc., to which the following licence agreement applies. Please read it carefully. SiRF LICENSE AGREEMENT IMPORTANT - READ CAREFULLY: This is a legal agreement (the “Agreement”) between SiRF Technology Incorpor...

Installation Templates T-1 GPS Antenna Mounting Template Note: Access to the underside of the mounting surface must be available to allow for secure fixing. Cable Exit Channel 18mm (0.7in) 6mm (0.25") dia. for cable only 19mm (0.75") dia. for NMEA plug 6mm (0.25") dia. 2 positions 18mm (...

In st al la ti o n T em pl at es T- 3 Raynav 300GPS Plot ter MountingT emplate 4.03 in (102.3 mm) 7.67 in (194.94 mm) 3.8 in (96.3 mm) 4.33 in (109.9 mm) Outer profile of instrument D4968-1 5.5 in (139.6 mm) Drill 4 mm hole (four positions) 300/320 T e mplate TO P Cut out shaded area only Note: Dril...

Index xi Index A Abbreviations 1 Accessories see Parts and Accessories Adding a Waypoint to a Route 21 , 31 Advance to Waypoint 35 Alarms Alarm Clock 45 Anchor 45 Arrival 37 , 45 Countdown Timer 45 Dedicated Key 45 External 45 MOB 44 Off Track 45 Setting 46 Silence 45 Alarms & Timers 45 Anchor A...

Document number: 84064-8 April 2001 Limited Warranty Certificate Raymarine warrants each new Light Marine/Dealer Distributor Product to be of good materials and workmanship, and will repair or exchange any parts proven to be defective in material and workmanship under normal use for a period of 2 ye...

Factory Service Centers United States of America UK, Europe, Middle East, Far East Raymarine Inc22 Cotton Road, Unit DNashua, NH 03063-4219, USA Raymarine LtdAnchorage Park, PortsmouthPO3 5TD, England Telephone: +1 603 881 5200Fax: +1 603 864 4756www.raymarine.com Telephone: +44 (0)23 9269 3611Fax: ...