Raymarine DSM300 - Manuals

6 DSM300 and DSM30 Installation Manual EMC Conformance All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. The design and manufacture of Raymarine equipment and accessories conform to the appropriate Electromagnetic Comp...

7 Chapter 1: DSM Installation 1.1 Introduction This chapter provides details for mounting the DSM300 and DSM30 and connecting to the display. For the system to display depth, water temperature and speed, you must install the transducer type(s) capable of transmitting the appropriate data. Planning t...

8 DSM300 and DSM30 Installation Manual • The equipment is supplied from a separate battery from that used for engine start. Voltage drops below 10 V and starter motor transients can cause the equipment to reset. This will not damage the equipment, but may cause the loss of some informa-tion and may ...

Chapter 1: DSM Installation 9 1.2 Unpacking and Inspecting the Components Unpack your system carefully, to prevent damage to the equipment. Save the carton and packing, in case you need to return the unit for service. Check that you have all the correct system components: Power Cable, 3m part no. R6...

10 DSM300 and DSM30 Installation Manual A 3m-long cable is included for connecting your sounder module to a C Series or hsb 2 PLUS (Pathfinder) Series display. Longer cables and connection cables for other types of systems must be purchased separately. Note: C Series displays have 4-pin connectors w...

Chapter 1: DSM Installation 11 • Interference: The selected location should be far enough away from devices that may cause interference, such as motors, generators, and radio transmitter/receivers. (See the EMC guidelines earlier in this chapter.) • Magnetic compass: Mount the unit at least 3 ft (1 ...

12 DSM300 and DSM30 Installation Manual To mount the DSM: 1. Hold the module in the location where you want to mount it, making sure it is perpendicular to the deck. 2. Mark the location of the four key holes onto the mounting surface. 3. Drill a 9/64" pilot hole at each of the marked locations....

14 DSM300 and DSM30 Installation Manual 1.5 Cable Runs Consider the following before installing the system cables: • You will need to attach power, transducer, and display cables. • All cables should be adequately secured, protected from physical damage, and protected from exposure to heat. • Avoid ...

Chapter 1: DSM Installation 15 Transducer Connection A 30 ft (10 m) cable is supplied with the transducer. This cable has a connector plug (with an outer nut that you must attach) at one end for attaching to the “T/D” connector on the sounder module. Optional extension cables are available. CAUTION:...

18 DSM300 and DSM30 Installation Manual Ground Connection It is important that an effective RF ground is connected to the system. A single ground point should be used for all equipment. You can ground the sounder module by connecting the drain wire (shield) of the Power Input cable to the boat’s RF ...

Chapter 1: DSM Installation 19 When used in a multiple display system, connect the DSM to the SeaTalk hs Network Switch. Configuring an E Series System - Multiple Displays Configuring C Series Displays The C Series system uses cables with a round 4-pin twist-lock network connector. A 3m-long C Serie...

20 DSM300 and DSM30 Installation Manual Configuring hsb 2 PLUS (Pathfinder) Series Displays hsb 2 PLUS network cables have a triangular 3-pin connector on both ends. When using the DSM with an hsb 2 PLUS Series display, connect the supplied 4-pin to 3-pin hsb 2 adapter between the sounder module and...

Chapter 2: Maintenance and Problem Solving 21 Chapter 2: Maintenance and Problem Solving This chapter provides information on routine maintenance and on possible causes of problems you may experience with your Digital Sounder Module. 2.1 Maintenance CAUTION: The sounder unit contains high voltage. A...

22 DSM300 and DSM30 Installation Manual Use only a water-based antifouling paint, or a water-based paint specifically designed for transducers. Apply the paint with a brush. If your transducer becomes fouled or stops working because of sand or sea growth, use a stiff brush to clean it. You may sand ...

Chapter 2: Maintenance and Problem Solving 23 2.2 Resetting the System The Reset function returns the sounder module to its factory default values. How you perform the reset depends on the type of display the sounder module is connected to. CAUTION: Factory ResetThe factory reset clears the sonar de...

24 DSM300 and DSM30 Installation Manual iii. An audible alarm is sounded.iv. The normal sonar image resumes scrolling across the display. The reset is complete. ➤ To cancel the reset: Before pressing YES as described in item 4 above, press any of the following keys: DISPLAY , MULTI , VRM/EBL , MARKS...

Chapter 2: Maintenance and Problem Solving 25 2.3 Problem Solving All Raymarine products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programs. However, if this unit should develop a fault, please refer to the following table to identify the most likely c...

26 DSM300 and DSM30 Installation Manual Status LED The LED on the connector panel provides valuable information on the status of your sounder module. The LED blinks green while the module is operating normally. If the unit detects a problem, the LED blinks amber to indicate a warning or red for an e...

28 DSM300 and DSM30 Installation Manual 2.4 How to Contact Raymarine On the Internet Visit the Raymarine World Wide Web site for the latest information on Raymarine electronic equipment and systems at: www.raymarine.com Customer Support Navigate to the Customer Support page for links to: • Finding F...

Chapter 2: Maintenance and Problem Solving 29 Technical Support For technical support, call: 1-800-539-5539 ext. 2444, or1-603-881-5200 ext. 2444. Our Technical Support Specialists are available to answer questions about installing, operating and trouble-shooting all Raymarine products. Questions ca...

30 DSM300 and DSM30 Installation Manual In Europe In Europe, Raymarine support, service and accessories may be obtained from your authorized dealer, or contact: Raymarine plcAnchorage ParkPortsmouth, HampshireEngland PO3 5TDTel:+44 (0) 23 9269 3611Fax:+44 (0) 23 9269 4642 Technical Support The Techn...

Appendix: Specifications 31 Appendix: Specifications General Sounder Features Approvals:CE - conform to 2004/108/EC (EMC), EN60945:2002 Size: 10.76" x 7.37" x 2.43" (273.3 x 187.2 x 61.7 mm) Weight: 2.2 lbs (1.0 kg) Mounting: Four keyholed mounting tabs, mounting screws Power: Voltage: D...

33 Index A Accessories 10 C C Series displays Connections 17 , 19 Cable Runs 10, 14 Cleaning Instructions 21 Configuration 18 Connections 14 C Series displays 17 , 19 Display 14 E Series displays 16 , 18 Ground 18 hsb2 19 , 20 hsb2 PLUS Series displays 17 , 20 Power 14 , 15 SeaTalk hs 14 , 18 System...