Powermatic 29 - Manuals - manualsarea.com

Page 4 - GENERAL SAFETY RULES; ELECTRICAL GROUNDING:; SPECIFIC SAFETY RULES

4 GENERAL SAFETY RULES READ THE MANUAL: Always read the owner's manual carefully before attempting to use the ma-chine. Know the limitations and hazards associatedwith its use. INSTALLATION: If mounting machine to the floor, use high quality anchor bolts through the mountingholes on the base. If usi...

Page 6 - ELECTRICAL WIRING; ASSEMBLY; FENCE ASSEMBLY; FIGURE 4

6 RECEIVING THE SHAPER Carefully unpack the shaper and any loose items fromthe wood crate and inspect for damage. Any dam-age should be reported to your distributor and ship-ping agent immediately. Before proceeding further,read your manual thoroughly to familiarize yourselfwith proper assembly, mai...

Page 7 - ADJUSTMENTS; BELT ADJUSTMENT/SPEED CHANGE; FIGURE 8

7 FIGURE 5 3. Mount the dust hood (J) to the rear of the fence body (A) with the four cross screws, Figure 6. FIGURE 6 MITER GAUGE/CLAMP ASSEMBLY The miter gauge and clamp are used for shaping theend of stock. To assemble the miter gauge:1. Assemble miter gauge (A) by placing bottom screw into hole ...

Page 10 - OPERATION; SHAPING WITH THE FENCE

10 Each half of the aluminum fence should be adjustedas close to the cutterhead as possible without inter-fering with it. Each can be moved independently de-pending on the type of work to be done:4. Loosen the knob (D) on the connection plate and slide aluminum fence (E) to position, Figure 16.Retig...

Page 11 - POSITION OF COLLARS

11 2. When the shaping operation removes the en- tire edge of the stock, e.g. in jointing or making a fullbead, the shaped edge will not be supported by theoutfeed fence when both fences are in line, Figure 20a.In this case, the stock should be advanced to the po-sition shown in Figure 20a and stopp...

Page 12 - MITER GAUGE; COPYING

12 FIGURE 24 NOTE: It is advisable to place the cutter as low as possible on the spindle to reduce spindle deflectionand ensure the best possible finish. Also make surethat the contacting surfaces of the cutter are smooth,clean and without dents. MITER GAUGE The miter gauge is used for shaping the e...

Page 13 - MAINTENANCE

13 FIGURE 27 MAINTENANCE Apply a drop of light machine oil occasionally on theledge and wall of the table opening to facilitate thechanging of table inserts. The bearings in the motor are sealed for life and donot require lubrication. The main shaft should be lubricated with grease regu-larly after ...

Page 14 - for Model 29 Shaper; PROBLEM

14 Trouble-Shooting for Model 29 Shaper PROBLEM POSSIBLE CAUSE SOLUTION Shaper will not start. 1. Fuse blown or circuit breaker tripped. 1. Replace fuse or reset circuit breaker. 2. Cord damaged. 2. Have cord replaced by authorized service person. Overload kicks out 1. Extension cord too light or to...

Page 16 - Fence Assembly; DESCRIPTION

16 NO. PART NO. DESCRIPTION 1 6292984 CHUTE, DUST 2 6292985 SCREW, HEX. SOC. SET M8 X 20 3 6292986 KNOB, ADJUSTMENT 4 6292987 PLATE 5 6292988 SCREW, ADJ. 6 6292989 RAM 7 6292990 HANDLE, LOCK 8 6292991 WASHER 9 6292992 CAP, R.H. 10 6292993 BLOCK, R.H. 11 6292994 BLOCK, L.H. 12 6292995 SCREW, HEX. SOC...

Page 18 - Spindle Assembly

18 PARTS LIST: Spindle Assembly (29 Shaper) NO. PART NO. DESCRIPTION 1 6293033 NUT, 3/4" SPINDLE 6293034 NUT, 1" SPINDLE 6293035 NUT, 1-1/4" SPINDLE 2 6293036 WASHER, KEYED 3 6293037 SET, SPACER 3/4" 6293038 SET, SPACER 1" 6293039 SET, SPACER 1-1/4" 4 6293040 NUT, RETAINER 5 ...

Page 20 - Shaper Body & Mitre Gauge Assemblies

20 PARTS LIST: Shaper Body & Mitre Gauge Assemblies (29 Shaper) NO. PART NO. DESCRIPTION 1 6293060 RING, INSERT 2 6293061 RING, INSERT 3 6293029 SCREW, HEX. SOC. HD. M5 X 12 4 6293062 SCREW, HEX. SOC. HD. M5 X 16 5 6293063 RING, INSERT 6 6293064 TABLE 7 6293065 WASHER, M12 8 6293066 CABINET 10 6...

Page 22 - Tilting Frame Assembly

22 PARTS LIST: Tilting Frame Assembly (29 Shaper) NO. PART NO. DESCRIPTION 1 6293124 SCREW, HEX SOC. HD. M10 X 35 2 6293115 WASHER, M10 3 6293125 PULLEY MOTOR 4 6293126 BUSHING 5 6293127 RETAINER 6 6293128 SCREW, HEX. SOC. SET,M10 X 35 7 6293129 NUT, HEX. M10 8 6293130 PLATE, MOTOR 9 6293131 HANDLE,...

Page 24 - ELECTRICAL SCHEMATIC:; Model 29 Tilting Shaper; THREE PHASE

24 ELECTRICAL SCHEMATIC: Model 29 Tilting Shaper THREE PHASE Y- START(2-STEP SWITCH) ∆∆∆∆∆ . O N T R A P N O I T P I R C S E D E P Y T N O I T A C I F I C E P S 4 7 0 3 9 2 6 H C T I W S V E R - R O F S C a 1 A 5 2 2 7 0 3 9 2 6 P O T S 1 B P b 1 C A V 0 5 2 A 0 1 1 7 0 3 9 2 6 T R A T S 2 B P a 1 C...

Page 26 - OPTIONAL ACCESSORIES

26 OPTIONAL ACCESSORIES Model 29 Tilting Shaper 6293198 1" Spindle Assembly, 6" under the nut. 6293199 1-1/4" Spindle Assembly, 6" under the nut. 6293200 460V transformer.

Page 28 - POWERMATIC