Planar PL2010M - Manuals - manualsarea.com

Page 3 - Table of Contents

1 Table of Contents Table of Contents............................................................................................................... 0 Preface ............................................................................................................................... 2 Chapter 1 I...

Page 4 - Preface; FCC Statement Warning; Warning; Canadian DOC Notice

2 Preface This manual is designed to assist users in setting up and using the LCD Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. Th...

Page 5 - Important Recycle Instruction:

3 Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean LCD Monitor screen: -- Power off LCD Monitor and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a rag. -- Gently clean the screen with dampe...

Page 6 - Chapter 1 Installation

4 Chapter 1 Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses ver...

Page 7 - Viewing Angle Adjustment; Connecting the Display to your Computer; Connecting the AC Power; Connecting the Audio Cable

5 Connecting the LCD Monitor and Base When you open the box to take the base and put on the desk first. Then connect the LCD Monitor and base please. (See fig.1-1 ) Figure 1-1 Viewing Angle Adjustment T h e L C D M o n i t o r i s d e s i g n e d t o a l l o w u s e r s t o h a v e a c o m f o r t a...

Page 8 - Interface for Arm Applications; VESA Flat; Power Management System

6 Optional Mounting Alternatives Detaching LCD Monitor from Its Stand Unscrew screws n the swivel base support column and pull down o the second. Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig.1-3. The rear of this LCD display has four integrated ...

Page 9 - User Controls

7 Chapter 2 Display Controls User Controls A brief description and the location of all LCD Monitor functions control and indicator: 8 Figure 2-1 1 Stereo Speakers PC Audio Stereo output. 2 Speaker Volume Control Increase Volume - Turn the knob clock wise. Decrease Volume - Turn the knob counter cloc...

Page 10 - Function Description

8 Function Description Ico n Function Function Description Brightness 101 scales of brightness are available to choose from (0 to 100). Contrast 101 scales of contrast are available to choose from (0 to 100). Horizontal Position This function adjusts the display's horizontal position Vertical Positi...

Page 11 - “OSD Lock Out” Function:

9 Notice: “OSD Lock Out” Function: When monitor is in normal display, you can enable the “OSD Lock Out” function. * How to enter “OSD Lock Out” function => Step 1: The monitor is displaying after power on. Step 2: To press the buttons “VOL –“ and “VOL+” and “Function >” at the same time for 3 ...

Page 12 - Chapter 3 Technical Information; Specifications

10 Chapter 3 Technical Information Specifications LCD Panel PL2010M Size 20.1" Display Type Active matrix color TFT LCD Resolution 1600x1200 Display Dot 1600 x (RGB) x 1200 Display Color 16.7M Video Input Signal Input Impedance Polarity Amplitude Multi-mode Supported Analog RGB 0.7Vp-p 75 Ohm ± ...

Page 14 - Standard Timing Table

12 Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing. TIMING FH(KHZ ) SYNC TOTAL ACTIVE SYNC FRONT BACK PIXEL FV(HZ) WIDTH PORCH PORCH POLARITY (DOT/ LINE) (DOT/ LINE) (DOT/LINE) (DOT/LINE) (DOT/LINE) FOREQ (MHZ)...

Page 15 - Troubleshooting; Attention

13 Note: Mode 640x350, 640x400 and 720x400 will locate on middle position but cannot be expanded to full screen on vertical direction. Troubleshooting This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market, use...