Pioneer PDK-50HW3 - Manuals

Page 2 - Scan device changes; a) The Pioneer badge need no longer be removed during installation.; An RS-232C connector is no longer provided.

2 Scan device changes a) The Pioneer badge need no longer be removed during installation. ¶ In this manual, the frame of the handwriting device that houses the sensor is referred to as a scan device. b) Instead of a 3 m RS-232C cable, a 1.4 m hard-wired USB cable is supplied. 1. The cable exit has b...

Page 3 - Device depth has been reduced for a slimmer look.; d) USB cable clip location

3 Changes from PDK-50HW2A to PDK-50HW3 2. Device depth has been reduced for a slimmer look. 80 (excluding screw heads) ] PDK-50HW2A PDK-50HW3 (excluding screw heads) 74 d) USB cable clip location A clip for securing two USB cables is provided on the rear panel to ensure that cables are neatly routed...

Page 4 - CBdrv

4 Changes from PDK-50HW2A to PDK-50HW3 Pen stand modifications a) The pen stand has been modified. The fitting is now more durable, but it is attached to the same location. ] PDK-50HW2A PDK-50HW3 Changes made to the pen a) The width of pen strokes is now thinner and more closely resembles those of a...

Page 5 - f) Test Mode indication has been changed.; Changes in service; Fixed low scan mode

5 Changes from PDK-50HW2A to PDK-50HW3 e) SXGA (1280 x 1024) 4:3 preset values have been added. f) Test Mode indication has been changed. ] PDK-50HW2A PDK-50HW3 g) Middle button (3-button emulation) is supported. ] See page 32. Changes in service a) Service Mode has been improved. Fixed low scan mod...

Page 6 - Contents

6 1. Specifications ............................................................ 7 1.1 Specifications ................................................................. 7 1.2 Accessories .................................................................... 8 1.2.1 Plasma display monitor (PDP-504CMX/PD...

Page 8 - Check that the following accessories were supplied.

8 1. Specifications 1.2 Accessories 1.2.1 Plasma display monitor (PDP-504CMX/PDP-50MXE1/PDP-50MXE1-S) Check that the following accessories were supplied. Use as a holder for theremote control unit.When attaching to therear of the main unit, becareful not to cover thevents. 1.2.2 Handwriting device (...

Page 10 - USB cable exit; PEN-NORMAL mode selector switch

10 1. Specifications <Rear panel> PEN-NORMAL mode selector switch (in lower left corner as seen from rear) N P 14 66 6 9 3 33 22 Plasma display side panel 22 20 11 5 Bottom panel of plasma display PDK-50HW3 center line Dimensions from right edge of PDK-50HW3 as seen from rear 2 Cable clip USB ...

Page 11 - Name and Function of Parts & Pin Layout; Mode selector switch; Name and function of parts

11 1. Specifications 1.4 Name and Function of Parts & Pin Layout 1.4.1 Plasma display monitor (PDP-504CMX/PDP-50MXE1/PDP-50MXE1-S) For information on the plasma display, refer to “Name and Function of Parts” in the Technical Manual supplied with the PDP-504CMX. 1.4.2 Handwriting device (PDK-50HW...

Page 12 - List showing compatibility of standard metal fittings

12 2.1 Installation Site The installation site precautions for the handwriting device are the same as those for the PDP-504CMX/PDP-50MXE1/ PDP-50MXE1-S. For details, refer to “Installation Site Requirements” in the Technical Manual of the PDP-504CMX/PDP- 50MXE1/PDP-50MXE1-S. 2.2 Installation Conditi...

Page 13 - Installation” in the Technical Manual of the plasma display.; the plasma display monitor in consideration.

13 2. Installation Site 2.2.2 Special installations Special installation conditions for the handwriting device are the same as for the plasma display. Refer to “Special Installation” in the Technical Manual of the plasma display. ¶ Calculate the distance between the monitor and surroundings (wall, e...

Page 14 - a) Installation of multiple systems; systems in NORMAL mode.; b) Exposure to direct sunlight; location will also make remote control operation erratic.

14 2. Installation Site 2.2.3 Installation precautions a) Installation of multiple systems Since the dedicated handwriting pen of the system is designed to function as a switch by emitting ultrasound waves, mutual interference may occur when more than one system is installed in proximity (the interf...

Page 15 - Installation Procedures

15 3.1 Unpacking 3.1.1 Plasma display monitor (PDP-504CMX/PDP-50MXE1/PDP-50MXE1-S) ¶ Any transportation of the unopened unit in its packaging should be done by two or more persons. To avoid injury or damage, do not lift the package by its packing bands. ¶ When transporting or storing the unit, alway...

Page 16 - Transportation precautions

16 3. Installation Procedures 3.1.2 Handwriting device (PDK-50HW3) Transportation precautions ¶ Do not stack more than four boxes on top of each other. Strictly observe the instructions on the outside of the box. Packing specifications: 1360 (W) × 900 (H) × 220 (D) mm, 12.7 kg Warranty Card 2 6 8 5 ...

Page 17 - Assembly and Connections; Place scan device over the front of the plasma display.

17 3. Installation Procedures 3.2 Assembly and Connections 3.2.1 Installing the handwriting device (PDK-50HW3) Notes: ¶ Always install the plasma display on a mobile cart before installing scan device. ¶ After installing scan device, never attempt to lift the plasma display to install on a mobile ca...

Page 18 - Pen stand; Changing the pen battery; Battery cover

18 3. Installation Procedures 3. Use the locking fixture on the rear panel to secure the four corners of scan device. 1 Rotate the locking fixture in the direction indicated by the arrow (rotate in the opposite direction for the left-side fixture), to secure scan device in place. 2 Press in the lock...

Page 19 - Connecting the plasma display to a computer; Computer Setup Example; Precautions regarding computer setup

19 3. Installation Procedures 3.2.3 Connecting the plasma display to a computer For information on connecting the plasma display to a computer, refer to “Installation and Connections” in the Operating Instructions supplied with the plasma display. Note: Turn the power off before making or changing c...

Page 20 - Adjusting the Plasma Display; Procedures for setting the plasma display

20 3. Installation Procedures 3.4 Adjusting the Plasma Display 3.4.1 Procedures for setting the plasma display For details, refer to the Technical Manual of the plasma display. 1. First, set the “System Settings”. Set “SIGNAL FORMAT”. To use 1280 x 768 (60 Hz/70 Hz) screen resolution and refresh rat...

Page 21 - Installing the Driver; USB cable

21 3. Installation Procedures 3.4.2 Screen burning Refer to “Screen Burning” in the Technical Manual supplied with the plasma display. 3.5 Installing the Driver 1. Install CBdrvU. Refer to “Installing the CBdrvU (Ver. 2.0) Driver” on page 25. 2. Reboot the computer. 3.6 Connecting a Scan Device to a...

Page 22 - How to Use Cable Clip; Use the cable clip to hold the unit's USB cable.; Sensor Operation Check; a) Check in Service Mode; and Service Mode” on page 38 in this manual.; b) Check in NORMAL mode; open the test window.

22 3. Installation Procedures 3.7 How to Use Cable Clip Use the cable clip to hold the unit's USB cable. USB cable Cable clip 3.8 Sensor Operation Check a) Check in Service Mode 1. Select the Service Mode and run SelfTest to check for abnormal operation. Set the internal DIP switches as described on...

Page 23 - Alignment of pen tip and cursor position; Using your mouse, left-click on the CBdrvU icon in the task tray.

23 3. Installation Procedures Pen tip Mouse cursor (screen display position) ¶ Alignment of pen tip and cursor position Confirm that the onscreen cursor aligns properly with the position of the pen tip. If the cursor position differs from that of the physical pen tip, adjust as follows: 1 Using your...

Page 25 - The software requires at least 6 MB of free hard disk space.; Installing and Using Software

25 4.1 Installing the CBdrvU (Ver. 2.0) Driver *Supplied with PDK-50HW3 4.1.1 Operating environment a) Operating environment ¶ Supported plasma displays: PDP-504CMX PDP-503CMX PDP-50MXE1 PDP-50MXE1-S PDP-503MXE ¶ Supported computers Model: IBM PC-AT or compatible CPU: Pentium 333 MHz or better Memor...

Page 26 - Use this procedure also for uninstalling the CBdrv software.; Using the Driver; There are the two following methods for operating CBdrvU.; a) Operation from the task tray; Open the menu from the task tray menu shown below.

26 4. Installing and Using Software 4.1.3 Uninstall procedures Use the following procedures to uninstall the installed CBdrvU software. Use this procedure also for uninstalling the CBdrv software. 1. Click the “Start” button on the Windows desktop. 2. Select “Settings” from the pop-up menu and then ...

Page 27 - b) Hot key operations

27 4. Installing and Using Software 2. Left-click on the CBdrvU icon in the task tray to open the pop-up menu shown below. [Overview] Current Resolution: Indicate current resolution Calibration: Open a screen for adjusting pen tip and cursor position Property: Perform pen settings Hardware Informati...

Page 28 - c) Scan device setup screen; Select pen calibration method.

28 4. Installing and Using Software c) Scan device setup screen This screen appears during scan device setup. (This screen closes automatically when setup completes). d) Scan device off screen This screen appears when the scan device is disconnected from the computer or when a malfunction occurs. (T...

Page 29 - The following modes are available.

29 4. Installing and Using Software [Overview] Easy Setting: Apply preset calibration by specifying currently displayed screen mode. The following modes are available. 1) FULL mode 2) 4:3 mode 3) DOT BY DOT mode Notes: ¶ Check the screen mode before making settings. Be sure to check the “SIGNAL FORM...

Page 30 - automatically after setup.

30 4. Installing and Using Software b) Calibration (Detail-2) When the plasma display is in the “PARTIAL” mode, use the mouse to click the two points, the upper and lower points to calibrate. Follow the on-screen calibration instructions and touch the points in the upper and lower half of the screen...

Page 31 - Make settings for the pen in this screen.; Set the effective double-click range of the pen.

31 4. Installing and Using Software 4.2.3 Property screen Make settings for the pen in this screen. [Sheet function overview] Double-click area: Set effective double-click range of the pen. Double-click speed: Set pen double-click speed. Other setup: Set to enable/disable the small button on the pen...

Page 33 - b) Test chart display

33 4. Installing and Using Software 4.2.4 Test Mode This is a service mode. Click “Test Mode” under “Hardware Information” in the CBdrvU task tray to open the screen shown below. a) State display This screen shows results of hardware checks and the state of the driver and the operating system (Windo...

Page 34 - Check driver version.

34 4. Installing and Using Software 4.2.5 Disabling CBdrvU Enable/disable CBdrvU. a) Disabling CBdrvU Checking the “Disable CBdrvU” checkbox displays the following message. Note: The pen cannot be used when CBdrvU is disabled. The CBdrvU icon appearance then changes as shown below. Screen appearance...

Page 35 - A check mark appears against currently selected rotate angle.

35 4. Installing and Using Software 4.3 Rotate 4.3.1 CBdrvU operation A video card enabling screen rotation is required for this function. a) Task tray display 1. Left-click the CBdrvU icon in the task tray to open the pop-up menu shown below. [Rotate functions] Rotate Mode: Select rotate angle. A c...

Page 36 - a) Use of video cards other than recommended; the “Select Calibration Dialog” to perform such settings.; d) Initial plasma display settings; “SIGNAL Format”; h) Pen operation in Welcome Login screen; Should this happen, use the mouse or keyboard for logging in.; i) Portrait installation of plasma display

36 4. Installing and Using Software 4.4 Precautions a) Use of video cards other than recommended A video card other than those recommended for use with CBdrvU must be calibrated from the Select Calibration Dialog (Detail-1). For information on recommended computers and video cards, consult a Pioneer...

Page 38 - Using Driver and Service Mode; b) Status displayed after pressing SelfTest button

38 4. Installing and Using Software 4.5 Using Driver and Service Mode 4.5.1 Service Mode display Press the Service Mode button in the “Test Mode” screen to open the “Service Information” screen. a) Screen items This screen shows service information and DIP switch information for handwriting device. ...

Page 39 - The detailed list indicates “ALL” and not data for each Point.

39 4. Installing and Using Software 2. When all components of test board D (LED) and all components of test board K (Sens) are malfunctioning. The detailed list indicates “ALL” and not data for each Point. 3. When some components of test board A (LED) and all test board H (Sens) components are malfu...

Page 40 - d) Readjustment of White Balance; Maintenance and Cleaning

40 Periodical maintenance is recommended to improve the service life and performance of the system. In the maintenance, clean the system equipment as described in the following. a) Plasma display monitor, scan device, remote control unit and special pen Never use solvents such as benzene or thinner,...

Page 41 - e) Replacing the pen tip; Insert one of the supplied replacement tips.

41 5. Maintenance and Cleaning e) Replacing the pen tip If the tip becomes deformed and writing quality deteriorates, replace the tip with one of the two supplied extras. Note: Continued use of a worn pen tip may damage the display. 1. Remove the tip. 2. Insert one of the supplied replacement tips. ...

Page 42 - Factory default status; a) To lock device in the NORMAL mode; ON; b) To make waveform observations; The touch panel input functions do not operate in this mode.; The touch panel input functions do not operate in this mode.; ON; Internal DIP Switch Settings

42 The test board A (LED) in the device is provided with 8-bit DIP switches (SW1). DIP switch settings are read only when the device is powered up and their values stay the same. : Factory default setting (All off) 1 2 3 4 5 6 7 8 ON Factory default status * Bits 5 to 8 should always be set to OFF. ...

Page 47 - General problems; Problems commonly mistaken as breakdown; Problem

47 If you think there is something wrong with this component, check the details in the following table. Sometimes another component may be the cause of the problem. Thus, also check the other devices that are connected to the plasma display. 8.1 Plasma Display (PDP-504CMX/PDP-50MXE1/PDP-50MXE1-S) Ge...

Page 48 - About the self diagnosis mode; Error messege

48 8. Troubleshooting Problem • Stripes appear on the screen. • Sound is heard from inside the unit. • Fan isn’t moving. • Fan speed changes. • ON (green) indicator doesn’t light. Possible Solution • May be caused by radio wave mingling from TV station, FM station, amateur radios, public radios (sim...

Page 50 - IR Scanning System; direction are located on the left seen from the front.; IR beam direction; resolution to match the plasma display monitor pixels (1280 x 768).; Vertical beam scanning direction; Horizontal beam; Capabilities of the Handwriting Device

50 9.1 IR Scanning System The handwriting device scans IR rays in the horizontal and vertical directions to detect the coordinate positions. There are 256 horizontal and 144 vertical sets of IR LEDs and sensors arranged on the panel. The IR sensors for the horizontal direction are located above the ...