Pioneer 2500 - Manuals
Pioneer 2500 – Manual in PDF format online.
Manuals:
Manual Pioneer 2500
Summary
2 CHAPTER 1. FEATURES OF PROJECTION CUBE SYSTEM .............................................................. 4 1. FEATURES OF SYSTEM ........................................................................................................................................... 4 2. FEATURES OF MULTI PR...
7 Dimensions GENERAL SPECIFICATIONS (Fig.2-1) 540 545 490 40 380
8 Power Supply Panel Name AC inlet AC outlet Main power switch Fuse holder Type See-saw switch Function GENERAL SPECIFICATIONS No. 1 2 3 4 1 Note 1) Refer to page 35 [(14) Connection with a power supply 3 Connection]. Connects AC power cord. Connects other multi-projection units. Not linked to main ...
20 GENERAL SPECIFICATIONS Front View Side View Rear View Main Specifications of Multi Video Processor (RMD-V2170) Input video signal ......................................... NTSC format Input signal band ...................................... Above 4.2 MHz Input Video input Input signal ..............
29 INSTALLATION AND ASSEMBLY (9) Ventilation for system The ventilation method differs according to where the system is installed. The following shows how to provide ventilation for the units according to the place of installation. Refer to these and keep the installation condition in the previous s...
37 2. INSTALLATION AND ASSEMBLY (1) Confirmation 1 Decide the position for installing the system according to the installation conditions in Chapter 3. Check Items [1] Dimensions of installing position, space at the back, distance to the ceiling [2] Floor flatness, strength, roughness [3] Position o...
43 (3) Carrying the Units After Opening Packaging To carry the screen unit and multi-projection unit after opening the packaging, hold them by the parts shown in the figure, and lift and move them. (Fig. 3-17) Screen Unit (Lifted by one or two persons) Multi-Projection Unit (Must be lifted by two pe...
45 (Fig. 3-19) H-shape frame assembly (L) 4 R i v e t 5 Shield 2 H-shape frame assembly (L) 1 Screw (M5 × 35) 1 Stopper Table 1 Base assembly B- 5 Guide fixture A- 5 Holder (R) A- 5 Holder (L) 2 H-shape frame assembly (R) 3 Horizontal frame assembly A- 7 B- 6 Screw (M5 × 35) 4. ASSEMBLING THE SYSTEM...
48 4 Multi Projection Unit (RM-V2400N/V2500N) The Multi-Projection Unit is designed to be mounted from the back of the cabinet normally. If sufficient space cannot be left at the back, it can be mounted from the front. (Fig.3-27) a When mounting from the back [1] Pull the table of the cabinet to the...
49 b When mounting from the front [1] Remove the two stoppers and two metal fixtures from the cabinet. (Fig. 3-32) [2] Pull the table to the front. [3] Insert the screws (M5 × 35) into the holes on the table. [4] Place the multi-projection unit on the table. [5] Attach the metal fixtures to the tabl...
50 5 Projection Screen Kit (RMS-V4011/V5011) [1] Mount the screen unit serving as the reference. Basically, mount from the center unit at the bottom. a If the number of units arranged are odd (E.g.: 3 × 3=9 screens) • Adjust the screen unit to the cabinet at the center of the bottom level and tempor...
59 INSTALLATION AND ASSEMBLY Perform the following steps to remove RM-V2400N from RMF-V4011CR. [1] When removing from the rear 1) Remove the screws of the engine guide and fixtures R and L attached to the cabinet. 4) Push out the projection unit. Leave the engine guide and fixtures R and L attached ...
60 INSTALLATION AND ASSEMBLY Screen 5. SPECIAL INSTALLATION (1) Wall inset • If removing the screen after installing the system, the person must go behind the screen (diagonally shaded part of the figure). Therefore when insetting the unit in the wall, careful take this into account before installat...
61 1. ADJUSTMENT PREPARATIONS (1) Wiring 1 Connection of Power Supply • The power supply can be connected to up to 3 units in a series using the AC outlets of Multi projection units. Connect the three units as one system to the external outlet. • The AC plug of Multi projection unit is a 3P with a g...
68 3. EXAMPLES OF MAIN USES OF MULTI-PROJECTION UNITS (1) Expansion/Individual Switching at Multi Video Processor Side - General example ADJUSTMENTS TV SYSTEM) AUTO Converter data required at display) One Source Multi Video Processor Multiprojection Unit NTSC NTSC Multi Video Processor LDP-2 LDP-1 *...
69 4. SCREEN ADJUSTMENTS (1) Adjustment Flowchart The following shows the order for performing the adjustments generally required in the setup of the multi-projection system. For details, see the descriptions on the next page and later. 1 Give ID ↓ 2 Adjust the size of each screen ↓ 3 Adjust the con...
71 ADJUSTMENTS The & numbers correspond to the numbers in the flow- chart. 2 Adjustment signal input For adjusting size...Frame size picture(EX.LD Test disc GGT1072, FRAME No. 5941),Monoscope, etc. For screen joining, linearity, color adjustment...Use adjustment signals such as , cross-hatch, et...
72 ADJUSTMENTS Observe here O b s e r v e here Reference Information To adjust the NTSC input for horizontal 93% and vertical 92%, use the frame size screen of the LD test disc GGT1072 (frame No. 5941). Horizontal : Adjust so that the sixth 92.5% line from the inside can be seen completely. Vertical...
87 ADJUSTMENTS H BLK R Adjustment Output all three colors R, G, B, observe the right side of the screen , and adjust with H BLK R so that the color stops deviating. RGB RGB BGR When H BLK R adjustment is not properly performed H BLK L adjustment Output all three colors R, G, B, observe the left side...
88 A C B D ADJUSTMENTS Confirming the Optimum H BLK L, H BLK R Values OSD display Optimum H BLK R value Movement on screen When point A is lowered by point convergence, point B should not move. Confirming the Optimum H BLK L Value When point C is lowered by point convergence, point D should not move...
92 5 Rough Adjustments (1) Black level adjustment Signal:White 10% Adjust R LOW, G LOW, and B LOW to the point where the CRT starts lighting up. (2) HI LIGHT adjustment Signal:White 50% Adjust R HI, G HI, and B HI so that the CRT becomes white. First, adjust so that the brightness of R, G, and B bec...
93 ADJUSTMENTS 6 LINEAR WHITE adjustment When white peak signals such as WINDOW are input, due to the characteristics of the Blue CRT, there is a tendency for the peak to become yellow compared to other colors. The linear white adjustment is performed to correct this tendency. Blue becomes weak when...
96 ADJUSTMENTS (6) External Control by RS-232C As Multi projection unit is equipped with a RS-232C port, various controls and, white balance and convergence adjustments can be performed by an external computer. By programming software ,it is possible not only to adjust White Balance,Convergence but ...
108 ADJUSTMENTS (7) Adjustments by Remote Control Multi projection unit adjustments can be performed using the remote control (RU-V107) besides the computer and software. All adjustments are performed only using the remote control. Up to 16 units can be operated using the remote control unit at one ...
114 2 Performing Adjustments 1) Entering and exiting the adjustment mode Turn on the power switch and press the two ADJ IN keys of the remote control together. The adjustment mode will be set. To exit this mode, press the ADJ OUT key of the remote control. The normal screen will return. 2) Using the...
115 ADJUSTMENTS 3 Adjustment Examples [1] Setting the ID 1) Enter the adjustment mode by ADJ IN key. 2) The main menu will be displayed. Press the 1 key to select [1. ID SET/CLEAR/SELECT]. 3) Check that the ID display at the top left of the screen is [– –]. Press the 1 key to select [1. ID SET]. Whe...
119 ADJUSTMENTS 4 Precautions Upon Use (Adjustment Control Unit) • Always release the adjustment mode with ADJ OUT button and turn off the power with the POWER button after adjust- ments and settings. All adjusted values and settings will be memorized. • The remote control adjustment mode will autom...
121 [2] Remove the panels at the top and right side of the screen unit to be replaced. (Remove 12 screws. ) The panels are made of polycarbonate. Adhesive double coated tapes are pasted to the frames. When removing the panels, do not pull the panels in directions which are difficult to pull, but pul...
129 OPERATIONS 3. PRECAUTIONS FOR ASSEMBLING AND MAINTENANCE • Periodically clean the vent nets of the fan of the multi-projection unit to prevent it from clogging. • In assemblies and maintenance, the service person must move in the cabinet. The following are precautions for this proce- dure. (1) D...
130 CHAPTER 6. PRECAUTIONS 1. PRECAUTIONS ON FUNCTION AND PERFORMANCE OF SYSTEM • The picture may turn to disorder temporarily due to power discharge inside the CRT tube, but it will recover automatically after a few seconds. In the new CRT, the very slight amount of impurities remaining inside (in ...
132 CHECK SHEET <CUBE Adjustment> 1. Preparations 1 Connect the power supply, and connect the cable for input signals and ABL link cable (control cable). 2 Place the connected cables neatly. 3 After completing the above 1 and 2 , turn on the power and perform aging for one hour. 4 Prepare the ...
Pioneer Manuals
-
Pioneer AHU
User Manual
-
Pioneer DMH WT6000NEX
User Manual
-
Pioneer DMH 2000NEX
User Manual
-
Pioneer DMH W3000NEX
User Manual
-
Pioneer DMH W3050NEX
User Manual
-
Pioneer HEAT PUMP
User Manual
-
Pioneer MINI-SPLITS OUTDOOR
User Manual
-
Pioneer SL405
User Manual
-
Pioneer AST-12UW3SXE**02
User Manual
-
Pioneer AST-09UW3SXE**01
User Manual
-
Pioneer ND BC010
User Manual
-
Pioneer TS A4671F
User Manual
-
Pioneer TS A653CH
User Manual
-
Pioneer TS A653FH
User Manual
-
Pioneer TS A683FH
User Manual
-
Pioneer TS A693CH
User Manual
-
Pioneer TS A693FH
User Manual
-
Pioneer VSX LX805
User Manual
-
Pioneer PN43 751 24U
User Manual
-
Pioneer PN50 751 24U
User Manual