Pelco CCC1300H-2X - Manuals

Page 2 - CONTENTS; LIST OF ILLUSTRATIONS

2 Pelco Manual C1961M-B (3/01) CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................. 3 REGULATORY NOTICES ........................................................................................... 3 DESCRIPTION .......................

Page 3 - IMPORTANT SAFEGUARDS AND WARNINGS; The product may bear the following marks:; REGULATORY NOTICES

Pelco Manual C1961M-B (3/01) 3 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should beobserved. 1. Installation and servicing should only be done by qualified service and installationpersonnel. 2. Installation shall be done in accordance with...

Page 4 - DESCRIPTION; MODELS; LOCATION AND FUNCTION OF PARTS; Back Focus Adjustment in this manual.

4 Pelco Manual C1961M-B (3/01) DESCRIPTION The CCC1300H-2, CCC1300H-2X, and MCC1300H-2 Digital Cameras are highresolution, compact video cameras that feature a 1/3-inch CCD imager. The camera’shigh resolution and high-density image sensor ensure a sharp and clear picture over awide range of conditio...

Page 5 - Sets the level for the brightest part of the picture. Anything

Pelco Manual C1961M-B (3/01) 5 Figure 1. Location and Function of Parts ESC - Electronic Sensitivity Control This function changes the sensitivity of the camera by varying the electronicshutter speed according to the amount of incident light. The ESC range is 1:300.To reset the ESC function switch, ...

Page 6 - POWER CONNECTIONS; To connect to the power supply:; VIDEO CONNECTIONS; Table A. Video Coaxial Cable Requirements

6 Pelco Manual C1961M-B (3/01) POWER CONNECTIONS To connect to the power supply: 1. Strip at least .50 inch (13 mm) from the power cord to expose the wires. 2. Insert the three wires into the holes in the terminal strip until they snap into place. 3. Confirm that the cord is connected to terminal se...

Page 7 - GENERAL LENS INFORMATION; LENS MOUNTING; PIN; GND; BACK FOCUS ADJUSTMENT; FIXED FOCAL LENGTH LENSES; Mount the lens firmly to the camera.

Pelco Manual C1961M-B (3/01) 7 GENERAL LENS INFORMATION The CCC1300H-2, CCC1300H-2X, and MCC1300H-2 can use fixed, manual, or passive(DC-controlled) auto iris lenses. The camera has a standard CS lens mount, but can usea C-mount lens when a C/CS-mount adapter is installed between lens and camera. LE...

Page 8 - MOTORIZED ZOOM LENSES

8 Pelco Manual C1961M-B (3/01) 5. Adjust the back focus.a. Use an Allen wrench to loosen the back focus lock screw at the side of thecamera. b. Turn the lens mount to obtain the sharpest image on the monitor. c. Turn the back focus locking ring clockwise to tighten. NOTE: Do not over tighen the back...

Page 9 - CAMERA SYNCHRONIZATION; Adjust the camera phase by pressing the LL switches up or down.

Pelco Manual C1961M-B (3/01) 9 CAMERA SYNCHRONIZATION The power supply of each camera is set to the same synchronized phase at thefactory and usually does not need to be readjusted. When using more than one camera power supply, a brief vertical roll may occur on themonitor each time a camera view is...

Page 10 - ECLIPSER ADJUSTMENT; Figure 2. Gray Level Setting

10 Pelco Manual C1961M-B (3/01) ECLIPSER ADJUSTMENT The eclipser is set at the factory and usually does not need to be readjusted. However,if fine tuning is necessary, do the following: 1. Set the DIP switches.a. AGC: OFF b. ELC: OFF c. BLC: OFF 2. Set the IRIS MODE selector.a. Auto iris lens contro...

Page 11 - SPECIFICATIONS; GENERAL

Pelco Manual C1961M-B (3/01) 11 SPECIFICATIONS GENERAL CCD Sensor: 1/3-inch interline transfer Picture Elements CCC1300H-2,MCC1300H-2: 768H x 494V(approx. 380K) CCC1300H-2X: 752H x 582V(approx. 440K) Sensing Area: 3/16 x 1/8 - inch(4.7 mm x 3.5 mm) SynchronizeSystem: AC Line lock Horizontal Resoluti...

Page 12 - REVISION HISTORY; Date; WARRANTY AND RETURN INFORMATION

REVISION HISTORY Manual # Date Comments C1961M 11/99 Original version. C1961M-A 3/01 Add information on model CCC1300H-2X. C1961M-B 3/01 Revised eclipser adjustment instructions. WARRANTY Pelco will repair or replace, without charge, any merchan-dise proved defective in material or workmanship for a...