Pelco CC3600 - Manuals - manualsarea.com

Page 3 - CONTENTS; LIST OF ILLUSTRATIONS

Pelco Manual C1981M-C (8/02) [ 3 ] CONTENTS IMPORTANT SAFEGUARDS AND WARNINGS ................................................................................. 4Regulatory Notices ...........................................................................................................................

Page 4 - IMPORTANT SAFEGUARDS AND WARNINGS; as vases, shall be placed on the apparatus.; RISK OF ELECTRIC SHOCK.

[ 4 ] Pelco Manual C1981M-C (8/02) IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near w...

Page 5 - DESCRIPTION; Models; Reorient or relocate the receiving antenna.

Pelco Manual C1981M-C (8/02) [ 5 ] DESCRIPTION The CC3500 and CC3600 Series are compact, color video cameras with a 1/3-inch CCD imager.All cameras have a direct drive/auto iris lens connector and adjustable back focus, and they acceptC and CS lenses. Models CC3500S-2 Standard resolution, 330 TV lin...

Page 6 - Lens Mounting; Loosen the two back focus locking screws. Rotate the back focus

[ 6 ] Pelco Manual C1981M-C (8/02) CAMERA LAYOUT INSTALLATION Lens Mounting The CC3500 and CC3600 Series cameras can use fixed iris, manual iris, auto iris, or direct drivelenses. Cameras are factory-set for CS-mount lenses, but easily adjusted for C-mount lenses. 1. C-Mount Lens Only - Loosen the t...

Page 7 - Camera Mounting

Pelco Manual C1981M-C (8/02) [ 7 ] PIN DD LENS CONNECTIONS AI LENS CONNECTIONS 1 Control coil negative (-) Not used 2 Control coil positive (+) Lens positive supply 3 Drive coil positive (+) Video drive signal 4 Drive coil negative (-) Ground Figure 2. DD/AI Lens Connector Camera Mounting Use a stan...

Page 8 - POWER AND VIDEO CONNECTIONS; Power Connections

[ 8 ] Pelco Manual C1981M-C (8/02) POWER AND VIDEO CONNECTIONS To connect the camera power and video do the following: 1. Remove the rear cover from the camera (refer to Figure 1). Thread cabling through the rear cover. 2. Connect the power cable to the two pin power connector on the back of the cam...

Page 9 - AC Operation Only; Recommended Wire Gauge and Wiring Distances; Wire Gauge; would require a minimum wire gauge of 20 AWG.; Maximum Distance; All-copper braided shield with 95% braid coverage

Pelco Manual C1981M-C (8/02) [ 9 ] AC Operation Only – If you are wiring more than one camera to the same transformer, connect one side of the transformer to the same terminal on all cameras, and connect the other side of the trans-former to the remaining terminal on all cameras. Failure to connect ...

Page 10 - LENS SETUP AND FOCUS PROCEDURES; Video Drive Auto Iris Lens; EI ON

[ 10 ] Pelco Manual C1981M-C (8/02) LENS SETUP AND FOCUS PROCEDURES Video Drive Auto Iris Lens When a video drive auto iris lens is used, the lens mode selector switch must be set to AI. Switch theEI and AGC OFF. Refer to the lens instructions and adjust the lens for the optimum picture (videooutput...

Page 11 - BACK FOCUS ADJUSTMENT; To adjust the back focus:

Pelco Manual C1981M-C (8/02) [ 11 ] BACK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side ofthe case. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side). 2. Turn the back focus ring: a. Clockwise...

Page 12 - SWITCH SETTINGS; BLACK REPRESENTS; Auto

[ 12 ] Pelco Manual C1981M-C (8/02) SWITCH SETTINGS Figure 7. Switch Settings 01236 10 9 8 7 6 5 4 3 2 1 BLACK REPRESENTS SWITCH POSITION 10 9 AUTO 10 9 6300 O K 10 9 3200 O K 10 9 4200 O K 8 8 NORMAL (0.45)LINEAR (1.0) 7 7 AGC ONAGC OFF 6 6 AI LENSDD LENS 5 5 INTERNAL LL Color Balance - Switch Sett...

Page 13 - Shutter Speed Selection -; ON; Flickerless; OFF

Pelco Manual C1981M-C (8/02) [ 13 ] Shutter Speed Selection - Switch Settings 4, 3, 2, and 1 4 3 2 1 1/50 4 3 2 1 1/125 1/250 1/500 1/1,000 1/2,000 1/4,000 1/10,000 4 3 2 14 3 2 1 4 3 2 14 3 2 1 4 3 2 14 3 2 1 00014 4 3 1 EI ON 4 3 EI OFF 4 2 BLC ON 4 2 BLC OFF 4 3 1 FLICKERLESS ON 4 1 FLICKERLESS O...

Page 14 - CAMERA SYNCHRONIZATION; To synchronize the cameras do the following:

[ 14 ] Pelco Manual C1981M-C (8/02) CAMERA SYNCHRONIZATION When using one AC power supply in a multi camera system, a brief vertical roll may occur on themonitor each time a camera view is switched. To eliminate vertical roll adjust the phase control tosynchronize (line-lock), the cameras to one ano...

Page 15 - SPECIFICATIONS; GENERAL

Pelco Manual C1981M-C (8/02) [ 15 ] SPECIFICATIONS GENERAL CCD Sensor: 1/3-inch Picture Elements CC3500S-2: 510 (H) x 492 (V) CC3500H-2: 768 (H) x 494 (V) CC3600H-2: 768 (H) x 494 (V) Sensing Area: 6mm diagonal Synchronization System: AC line lock or internal oscillator Horizontal Resolution CC3500S...

Page 16 - WARRANTY AND RETURN INFORMATION; REVISION HISTORY; Date; Revised Lens Setup and Focus Procedures.

® Pelco, the Pelco logo, Spectra, Genex, Legacy, PelcoVision, Esprit, and Camclosure are registered trademarks of Pelco. ™ HyperHAD and EXview HAD CCD are trademarks of the Sony Corporation. © Copyright 2002, Pelco. All rights reserved. WARRANTY AND RETURN INFORMATION REVISION HISTORY Manual # Date ...