Omron M3W- Manuals

Page 3 - Important Safety Information

1 EN Important Safety Information Consult your doctor prior to using in pregnancy or if diagnosed with arrhythmia or arteriosclerosis.Please read this section carefully before using the unit. Warning: • Indicates a potentially hazardous situation which, if not avoided, could result in death or serio...

Page 5 - Overview; Main unit; Open the rear cover page to read following:

3 EN 1. Overview Main unit DisplayO/I START ( ) button User A/B buttonUp/Down ( ) buttons Buzzer and Date/Time setting ( ) button Air JackBattery compartmentAC adapter jack (for optional AC adapter) Arm cuff Arm cuff (Wide Range Cuff: arm circumference 22-42cm)MarkerAir tubeAir plug Display Systolic...

Page 6 - Preparation; Remove the battery cover.

4 2. Preparation 2.1 Installing/Replacing the Batteries 1. Remove the battery cover. 2. Insert four “AA” batteries as indicated in the battery compartment and then replace the battery cover. Notes: • If the battery low symbol ( ) appears on the display, turn the unit off then replace all batteries a...

Page 7 - Setting the Buzzer/ Date and Time; Press the

5 2. Preparation EN 2.2 Setting the Buzzer/ Date and Time 1. Press the button. 2. Set the Buzzer. 3. Set the monitor to the correct date and time before taking a measurement for the first time. 4. Press the O/I START button to store the setting. Notes: • If the batteries have been removed for 30 sec...

Page 8 - Using the Unit; Applying the Arm Cuff; Insert; Open both the front and rear covers to read following:

6 3. Using the Unit 3.1 Applying the Arm Cuff Remove tight-fitting clothing or tight rolled up sleeve from your upper arm.Do not place the cuff over thick clothes. 1. Insert the air plug into the air jack. 2. Put your arm through the cuff loop. 3. Position the arm correctly. The bottom edge of the c...

Page 9 - How to Sit Correctly

7 3. Using the Unit EN 3.2 How to Sit Correctly To take a measurement, you need to be relaxed and comfortably seated, under comfortable room temperature. No eating, smoking or exercising 30 minutes before taking a measurement. • Sit on a chair with your feet flat on the floor.• Sit upright with your...

Page 10 - Taking a Reading

8 3. Using the Unit 3.3 Taking a Reading Notes: • To cancel a measurement, press the O/I START button to turn off the unit and to release the air in the arm cuff.• Remain still while taking a measurement. The monitor is designed to take measurements and store the measurement values in the memory for...

Page 12 - Press the O/I START button to turn off the monitor.

10 3. Using the Unit 4. Remove the arm cuff. 5. Press the O/I START button to turn off the monitor. The monitor automatically stores the measurement in its memory.It will automatically turn off after five minutes. Important: • Recent research suggests that the following values can be used as a guide...

Page 14 - Using the Memory Function; To View the Average Value; Press the or button.

12 3. Using the Unit 3.4 Using the Memory Function The monitor automatically stores the result up to 60 sets for each user (A and B). It can also calculate an average reading based on the measurements from the last three readings taken within 10 minutes. If there are only two readings in memory for ...

Page 15 - To View the Readings Stored in Memory; Press the button, while the average value is displayed.; To Delete All the Values Stored in Memory

13 3. Using the Unit EN To View the Readings Stored in Memory 1. Press the button, while the average value is displayed. The Memory number appears for a second before the pulse rate is displayed. The newest set is numbered “1”. 2. Press the or button to view the readings stored in memory. : To the o...

Page 16 - Troubleshooting and Maintenance; The Icons and Error Messages

14 4. Troubleshooting and Maintenance 4.1 The Icons and Error Messages Error Display Cause Remedy Irregular or weak pulses are detected. Remove the arm cuff. Wait 2-3 minutes and then take another measurement. Repeat the steps in section 3.3. If this error continues to appear, contact your doctor. M...

Page 17 - Troubleshooting and Maintenance

15 4. Troubleshooting and Maintenance EN Note: The irregular heartbeat symbol ( ) may also be displayed with error messages. Cuff is under inflated. Carefully read and repeat the steps listed under section 3.3. Movement during measurement. Repeat measurement. Remain still and do not talk during meas...

Page 18 - Troubleshooting

16 4. Troubleshooting and Maintenance 4.2 Troubleshooting Problem Cause Remedy The reading is extremely low (or high). Arm cuff not applied correctly. Apply the arm cuff correctly. Refer to section 3.1. Movement or talking during measurement. Remain still and do not talk during measurement.Refer to ...