Numark TT500 - Manuals - manualsarea.com

Page 2 - SAFETY PRECAUTIONS

Thank you for purchasing this Numark product. Please read these operating instructions so you will know how to operate this equipment properly. After you have finished reading these instructions, keep them for future reference. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE T...

Page 4 - SETUP & INSTALLATION; Mixer; Mixer; SETUP AND INSTALLATION

SETUP & INSTALLATION This turntable has been designed exclusively for DJ use and can be setup in a variety of different ways depending on your mixing style. The turntable should rest on a level and stable surface that is clear of obstructions. If a mixer is placed between two turntables make sur...

Page 5 - General Controls; CONTROLS

CONTROLS General Controls 1. Power Button This button turns on the turntable when pressed. It illuminates blue when the turntable is switched on. 2. Platter This turntable has a special edge design that has been optimized for "dragged" platter slow downs. (NOTE: The pattern will appear to st...

Page 6 - The S-weight can be stored below the counterweight in the top

CONTROLS continued 9. Pitch Fader This slide control allows the pitch of the playback source to be changed. In the center position the pitch is at 0%. Moving the fader knob closer to you will increase the pitch. The Pitch Slider is enclosed in an Interchangeable/Replaceable Cartridge. 10. Pitch Butt...

Page 7 - continued

CONTROLS continued Bottom Parts 20. Adjustable Rubber Dampening Feet When all of the feet of the turntable are completely tightened, the top flat surface of the turntable will be at 85mm. Unscrewing these feet raises the turntable up to compensate for unleveled surfaces. 21. Carrying Handles These h...

Page 8 - CABLE SETUP

CABLE SETUP This turntable is shipped with two sets of special cables: (1) Right Angle IEC Power Cord (1) Right Angle RCA cord NOTE: Before connecting any cables, make sure that the voltage selector switch is set to the proper setting! Making the power and audio connections: 1. Begin by lifting the ...

Page 9 - AL; PLATTER SETUP

PLATTER SETUP WARNING: Incorrect Platter setup can lead to poor turntable performance, platter instability, or permanent motor damage. 1. Start by inspecting the bottom of the aluminum platter to check that both locking pins have rubber fittings on them. 2. Next, rotate the platter spindle so that t...

Page 10 - INTERCHANGING TONEARM TUBES

INTERCHANGING TONEARM TUBES WARNING : An incomplete understanding of this procedure could lead to permanent damage to the headshell, your records, or the tonearm assembly. NOTICE : Interchanging tonearm tubes unnecessarily may shorten the life of the tonearm tubes and/or tonearm components. This tur...

Page 11 - TONE ARM SETUP; MIN

TONE ARM SETUP A properly adjusted tone arm and cartridge setup will minimize vinyl record wear and optimize the performance of the turntable. Follow these simple steps for setting the tone arm on the turntable: NOTE: In most cases, when using the S-Shaped tonearm tube, the additional S-Weight must ...

Page 12 - CARTRIDGE SETUP

CARTRIDGE SETUP For Head Shell Mounted Cartridges: The cartridge that comes with this turntable should be preinstalled on the head shell. If it isn't, please follow the below instructions for installing a cartridge onto the head shell. 1. Position the head shell and the cartridge so that the four co...

Page 13 - IMPORTANT NOTES & OPERATION

OTHER IMPORTANT NOTES Please read these precautionary notes to insure a complete understanding and long life of this DJ turntable. 1. Unnecessarily removing the platter may cause damage to the magnet mounting structure, the motor or the platter resulting in undesired performance. The turntable shoul...

Page 14 - SPECIFICATIONS

SPECIFICATIONS Turntable: Torque (transient): 4.5kgf.cm Torque (stable): 3.5kgf.cm Motor: Brushless DC motor Brake: Electronic braking system Platter: Dampened aluminum diecast, low friction design Pitch: +/-8%, 10%, 25%, 50% Speeds: 33 1/3RPM, 45RPM, 78RPM Wow/flutter: <0.15% max, <0.10% typi...