Netgear GS510TP-100NAS - Manuals

5 0 0. About This Manual The NETGEAR® ProSafe TM GS510TP Hardware Installation Guide describes how to install and power on the GS510TP Smart Switch. The information in this manual is intended for readers with intermediate computer and Internet skills. Conventions, Formats, and Scope The conventions,...

This is a safety warning. Failure to take heed of this notice may result in personal injury or death. 6 NETGEAR GS510TP Smart Switch • Scope. This manual is written for the GS510TP Smart Switch according to these specifications: Product Version GS510TP Smart Switch Manual Publication Date October 20...

7 1 1. Introduction Congratulations on the purchase of your NETGEAR ® ProSafe TM GS510TP Smart Switch. The GS510TP is a supplement to the Gigabit Advanced Smart Switch family. Available as a desktop or rack-mountable.The GS510TP is a PoE-supportable low-port switch with two fiber uplinks included. T...

Introduction 8 NETGEAR GS510TP Smart Switch full-duplex mode. The maximum segment length is 328 feet (100 meters) over Category 5 Unshielded Twisted-Pair (UTP) cable. Features The following list identifies the key features of the GS510TP Smart Switch: • Eight RJ-45 10/100/1000 Mbps autosensing Gigab...

Introduction 9 NETGEAR GS510TP Smart Switch • PoE is enabled by default. Green Features The GS510TP Smart Switch supports the following power-saving features: • The power consumption automatically adjusts based on the RJ-45 cable length. • Each port is configured to power down automatically when the...

11 2 2. Physical Description This chapter describes the NETGEAR GS510TP Smart Switch hardware features. Topics include: • GS510TP Front-Panel Configuration • LED Designations • Device Hardware Interfaces GS510TP Front-Panel Configuration The GS510TP has eight 10/100/1000 Mbps autosensing and two 100...

Physical Description 12 NETGEAR GS510TP Smart Switch • Fan LED • PoE Max LED GS510TP Back-Panel Configuration Figure 3 illustrates the GS510TP back panel. Power Connector Figure 3. GS510TP Back Panel The back panel contains the following: • Internal 150W open frame power supply for the GS510TP.

Physical Description 13 NETGEAR GS510TP Smart Switch LED Designations Port LEDs Table 1 describes the RJ-45 and SFP port LED designations. There are two LEDs for each RJ-45 port. Table 1. Port LEDs LED Designation Speed/Link/Activity SPD/Link/ACT LED: • Off = No link is established on the port. • So...

Physical Description 14 NETGEAR GS510TP Smart Switch System LEDs Table 2 describes the system LED designations. Table 2. System LEDs LED Designation Power/Status LED • Solid Green = Power is supplied to the switch and the switch is operating normally. • Solid Yellow = The switch is booting. • Off = ...

Physical Description 15 NETGEAR GS510TP Smart Switch device such as a paper clip into the opening to press the recessed button. The front-panel LEDs should extinguish and light again as the switch performs its Power On Self Test (POST). Factory Defaults Button The Smart Switch has a Factory Defaults...

17 3 3. Applications Your NETGEAR GS510TP Smart Switch is designed to provide flexibility in configuring your network connections. It can be used as a stand-alone device or with 10 Mbps, 100 Mbps, and 1000 Mbps hubs and switches. Desktop Switching The GS510TP Smart Switch can be used as a desktop sw...

19 4 4. Installation This chapter describes the installation procedures for your NETGEAR GS510TP Smart Switch. Switch installation involves the following steps: Step 1: Preparing the Site Step 2: Installing the Switch Step 3: Checking the Installation Step 4: Connecting Devices to the Switch Step 5:...

Installation 20 NETGEAR GS510TP Smart Switch Step 2: Installing the Switch The GS510TP Smart Switch can be used on a flat surface or mount in a rack. Installing the Switch on a Flat Surface The switch ships with four self-adhesive rubber footpads. Stick one rubber footpad on each of the four concave...

Installation 21 NETGEAR GS510TP Smart Switch Step 3: Checking the Installation Before applying power to the switch, perform the following: • Inspect the equipment thoroughly. • Verify that all cables are installed correctly. • Check cable routing to make sure cables are not damaged or creating a saf...

Note: The PoE port may be considered SELV circuits, if it is not likely to require connection to an Ethernet network with outside plant routing, including campus environment; and the installation instructions clearly state that the ITE is to be connected only to PoEnetworks without routing to the ou...

25 A A. Troubleshooting This chapter provides information about troubleshooting the NETGEAR Smart Switch. Topics include the following: • Troubleshooting Chart • Additional Troubleshooting Suggestions Troubleshooting Chart The following table lists symptoms, causes, and solutions of possible problem...

Troubleshooting 26 NETGEAR GS510TP Smart Switch Additional Troubleshooting Suggestions If the suggestions in Troubleshooting Chart do not resolve the problem, refer to the troubleshooting suggestions in this section. Network Adapter Cards Ensure the network adapter cards installed in the PCs are in ...

27 B B. Technical Specifications Network Protocol and Standards Compatibility IEEE 802.3i 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x flow control IEEE 802.3z 1000BASE-X IEEE 802.3at DTE Power via MDI Management Windows 2000 + XP, Vista; Microsoft Explorer 6.0 or higher IEEE ...

Technical Specifications 29 NETGEAR GS510TP Smart Switch Operating humidity: 10% to 90% maximum relative humidity, noncondensing Storage temperature: –20°C to 70°C (–4 to 158°F) Storage humidity: 5% to 95% maximum relative humidity, noncondensing Electromagnetic Emissions FCC Class A CE Class A: Inc...

31 Index Numerics 8-pin 14 A Applying AC Power 22 Auto Uplink 14 Auto-negotiating 8 Autosensing 8 , 14 B Backpressure 8 C Category 5 Unshielded Twisted-Pair 8 Checking the Installation 21 Class of Service 7 Connecting Devices to the Switch 21 Copper 7 Crossover 14 D Default IP Address 23 Default Res...