Page 2 - Technical Support; Please register to obtain technical support; . Please retain your proof of purchase and warranty; Trademarks
ii 202-10009-01_060204 © 2004 by NETGEAR, Inc., June 2004. FullManual All rights reserved. Technical Support Please register to obtain technical support . Please retain your proof of purchase and warranty information. To register your product, get product support or obtain product information and pr...
Page 3 - Canadian Department of Communications Compliance Statement; EN 55 022 Declaration of Conformance
202-10009-01_060204 iii Canadian Department of Communications Compliance Statement This Class B Digital apparatus (NETGEAR 7300 Series Layer 3 Managed Switch) meets all the requirements of the Canadian Interference Causing Equipment Regulations. Cet appareil numerique del la classe B respect les exi...
Page 5 - Contents
Contents v 202-10009-01_060204 Contents Chapter 1 About This Guide Audience ......................................................................................................................... 1-1 Why the Document was Created ........................................................................
Page 27 - Chapter 1; Thank you for purchasing the NETGEAR; Audience; Chapter 6, “Quick Start up”
About This Guide 1-1 202-10009-01_060204 Chapter 1 About This Guide Thank you for purchasing the NETGEAR ™ 7300 Series L3 Switch. Audience This reference manual assumes that the reader has basic-to-intermediate computer and Internet skills. However, basic computer network, Internet, and wireless tec...
Page 28 - Typographical Conventions; This guide uses the following typographical conventions:; Special Message Formats; Product updates are available on the NETGEAR, Inc. Web site at
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 1-2 About This Guide 202-10009-01_060204 Note: Refer to the release notes for the 7000 Series L3 Managed Switch Software application level code. The release notes detail the platform specific functionality of the Switching, Rout...
Page 29 - Features of the HTML Version of this Manual; Show in Contents; Right pane
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software About This Guide 1-3 202-10009-01_060204 Features of the HTML Version of this Manual The HTML version of this manual includes these features. Figure Preface -2: HTML version of this manual 1. Left pane . Use the left pane to vie...
Page 30 - How to Print this Manual; Printing a “How To” Sequence of Steps in the HTML View; Print; Printing a Chapter
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 1-4 About This Guide 202-10009-01_060204 How to Print this Manual To print this manual you man choose one of the following several options, according to your needs. • Printing a “How To” Sequence of Steps in the HTML View . Use ...
Page 31 - Chapter 2; Switch Management Overview; Management Access Overview; Scope; The maximum number of configuration file command lines is 2000.
Switch Management Overview 2-1 202-10009-01_060204 Chapter 2 Switch Management Overview This chapter gives an overview of switch management, including the methods you can use to manage your NETGEAR NETGEAR 7300 Series Layer 3 Managed Switch. • Management Access Overview • SNMP Access • Protocols Sco...
Page 32 - Simple Network Protocol Management (SNMP)
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 2-2 Switch Management Overview 202-10009-01_060204 • Simple Network Protocol Management (SNMP) Each management method enables the network administrator to configure, manage, and control the managed switch locally or remotely usi...
Page 33 - Chapter 3; shows an example of this management method.; Set Up Your Switch Using Direct Console Access; “Web Based Management Overview” on page 4-1
Administration Console Telnet Interface 3-1 202-10009-01_060204 Chapter 3 Administration Console Telnet Interface The administration console is an internal, character-oriented, VT-100/ANSI menu-driven user interface for performing management activities. Using this method, you can view the administra...
Page 34 - Examples of terminal-emulation programs include:; OK
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 3-2 Administration Console Telnet Interface 202-10009-01_060204 Examples of terminal-emulation programs include: • HyperTerminal, which is included with Microsoft Windows operating systems • ZTerm for the Apple Macintosh • TIP f...
Page 35 - None
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Administration Console Telnet Interface 3-3 202-10009-01_060204 4. When the following screen appears, make sure that the port setting are as follows: Baud Rate: 9600 Data Bits: 8 Parity: None Stop Bits: 1 Flow Control: None Figu...
Page 37 - Chapter 4; shows this management method.; Web Based Management Overview; The help menu contains:
Web-Based Management Interface 4-1 202-10009-01_060204 Chapter 4 Web-Based Management Interface Your NETGEAR 7300 Series Layer 3 Managed Switch provides a built-in browser interface that lets you configure and manage it remotely using a standard Web browser such as Microsoft Internet Explorer 5.0 or...
Page 38 - How to Log In to the Managed Switch; admin
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 4-2 Web-Based Management Interface 202-10009-01_060204 • Device Management Introduction of the basic icons and management of the device • Interface Operations Describes Web browser requirements, and common commands • Product Ove...
Page 39 - Click the Login link.; and default of no password, or whatever password you
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Web-Based Management Interface 4-3 202-10009-01_060204 Click the Login link. A user name and password dialog box opens like this one. Figure 4-4: User name/password dialog box 4. Type the default user name of admin and default o...
Page 40 - Web-Based Management Utility Features
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 4-4 Web-Based Management Interface 202-10009-01_060204 Web-Based Management Utility Features Figure 4-5: System Information page This welcome page displays system information, such as: • System Description • System Name • System...
Page 41 - Interactive Switch Image; Menus
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Web-Based Management Interface 4-5 202-10009-01_060204 Interactive Switch Image Figure 4-6: Interactive switch image This dynamic image shows various real time conditions about the switch, including the status, fan operation, po...
Page 42 - Main Menus; Management
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 4-6 Web-Based Management Interface 202-10009-01_060204 Figure 4-7: Menu navigation Main Menus • Management • Switch • Routing • Traffic Management
Page 43 - Secondary Menus
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Web-Based Management Interface 4-7 202-10009-01_060204 • Smart Wizard Secondary Menus The Secondary Menus under the Main Menu contain a host of options that you can use to configure your switch. The online help contains a detail...
Page 44 - Routing; Traffic Management; Chapter 10, “CLI Commands: Differentiated Services; Smart Wizard; “Routing Commands” on page 9-1; System-Wide Popup Menus
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 4-8 Web-Based Management Interface 202-10009-01_060204 Routing • Routing Commands — see “Routing Commands” on page 9-1 Traffic Management • Diffserv — see Chapter 10, “CLI Commands: Differentiated Services • Traffic Control — se...
Page 45 - Port-Specific Popup Menus
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Web-Based Management Interface 4-9 202-10009-01_060204 Port-Specific Popup Menus The 7300 Series L3 Switch also provides several popup menus for each port. Figure 4-9: Switch popup menus You can access a port-specific popup menu...
Page 47 - Chapter 5; CLI Command Format; network parms; snmp-server location; clear vlan; Command
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Command Line Interface Structure 5-1 202-10009-01_060204 Chapter 5 Command Line Interface Structure The Command Line Interface (CLI) syntax, conventions and terminology are described in this section. Each CLI command is illustra...
Page 48 - Parameters; Parameters are order dependent.; Values; ipaddr
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 5-2 Command Line Interface Structure 202-10009-01_060204 Parameters Parameters are order dependent. The text in bold italics should be replaced with a name or number. To use spaces as part of a name parameter, enclose it in doub...
Page 49 - Conventions
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Command Line Interface Structure 5-3 202-10009-01_060204 logical slot/port This parameter denotes a logical slot number and logical port number assigned. This is applicable in the case of a port-channel (LAG). The operator can u...
Page 50 - Annotations; Some examples are provided below:; ! Script file for displaying the ip interface
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 5-4 Command Line Interface Structure 202-10009-01_060204 Annotations The CLI allows the user to type single-line annotations at the command prompt for use when writing test or configuration scripts and for better readability. Th...
Page 51 - Chapter 6; Quick Starting the Switch
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Quick Start up 6-1 202-10009-01_060204 Chapter 6 Quick Start up The CLI Quick Start up details procedures to quickly become acquainted with the 7300 Series L3 Switch. Quick Starting the Switch 1. Read the device Installation Gui...
Page 52 - System Info and System Setup
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 6-2 Quick Start up 202-10009-01_060204 System Info and System Setup Quick Start up Software Version Information Quick Start up Physical Port Data Table 6-1. Quick Start up Software Version Information Command Details show hardwa...
Page 53 - Simple Network Management Protocol - SNMP
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Quick Start up 6-3 202-10009-01_060204 Quick Start up User Account Management Quick Start up IP Address To view the network parameters the operator can access the device by the following three methods. • Simple Network Managemen...
Page 55 - config - configuration file
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Quick Start up 6-5 202-10009-01_060204 Quick Start up Uploading from Switch to Out-of-Band PC (Only XMODEM) Table 6-5. Quick Start up Uploading from Switch to Out-of-Band PC (XMODEM) Command Details copy { nvram:startup-config |...
Page 59 - Chapter 7
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Mode-based CLI 7-1 202-10009-01_060204 Chapter 7 Mode-based CLI The CLI groups all the commands in appropriate modes according to the nature of the command. A sample of the CLI command modes are described below. Each of the comm...
Page 63 - Mode-based Command Hierarchy; The CLI provides the following modes:
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Mode-based CLI 7-5 202-10009-01_060204 Mode-based Command Hierarchy The CLI is divided into various modes. The Commands in one mode are not available until the operator switches to that particular mode, with the exception of the...
Page 64 - DHCP Pool Config Mode.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 7-6 Mode-based CLI 202-10009-01_060204 the router interface configuration commands. The command prompt at this level is: Command Prompt: $(Interface <slot/port>)# The resulting prompt for the interface configuration comman...
Page 65 - Flow of Operation; This section captures the flow of operation for the CLI:
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Mode-based CLI 7-7 202-10009-01_060204 $(Config)# ip dhcp pool <pool-name> Command Prompt: (Config-dhcp-pool)# Flow of Operation This section captures the flow of operation for the CLI: 1. The operator logs into the CLI se...
Page 66 - “No” Form of a Command; Appendix A, “IS CLI Mapping; Support for “No” Form
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 7-8 Mode-based CLI 202-10009-01_060204 4. Once the control has reached the callback function, the callback function has complete information about the parameters entered by the operator. “No” Form of a Command "No" is a ...
Page 67 - Chapter 8; System Information and Statistics Commands; Format; Mode; MAC Address
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-1 202-10009-01_060204 Chapter 8 Switching Commands This chapter provides detailed explanation of the Switching commands. The commands are divided into five functional groups: • Show commands display switch s...
Page 68 - show hardware
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-2 Switching Commands 202-10009-01_060204 numbers that are separated by colons, for example 01:23:45:67:89:AB IP Address The IP address assigned to each interface. slot/port Valid slot number and a valid port number. show event...
Page 69 - show interface
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-3 202-10009-01_060204 Burned in MAC Address Universally assigned network address. Software Version The release.version.revision number of the code currently run-ning on the switch. Operating System The opera...
Page 70 - show interface ethernet; Octets Received
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-4 Switching Commands 202-10009-01_060204 Packets Received Without Error The total number of packets (including broadcast pack- ets and multicast packets) received by the processor. Broadcast Packets Received The total number o...
Page 71 - Packets Received < 64 Octets
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-5 202-10009-01_060204 this equation is the value Utilization which is the percent utiliza-tion of the ethernet segment on a scale of 0 to 100 percent. Packets Received < 64 Octets - The total number of pa...
Page 72 - Packets Received with MAC Errors
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-6 Switching Commands 202-10009-01_060204 Unicast Packets Received - The number of subnetwork-unicast packets delivered to a higher-layer protocol. Multicast Packets Received - The total number of good packets received that wer...
Page 73 - Packets Transmitted Octets
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-7 202-10009-01_060204 Total - A count of valid frames received which were discarded (i.e. filtered) by the forwarding process. Local Traffic Frames - The total number of frames dropped in the forwarding proc...
Page 74 - Packets Transmitted 64 Octets
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-8 Switching Commands 202-10009-01_060204 Packets Transmitted 64 Octets - The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets). Packets Tra...
Page 75 - Transmit Errors
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-9 202-10009-01_060204 Broadcast Packets Transmitted - The total number of packets that higher-level protocols requested be transmitted to the Broad-cast address, including those that were discarded or not se...
Page 76 - Dot1x Statistics
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-10 Switching Commands 202-10009-01_060204 BPDU's Transmitted - The count of BPDU's (Bridge Protocol Data Units) transmitted from the spanning tree layer. 802.3x Pause Frames Received - A count of MAC Control frames received on...
Page 79 - Static
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-13 202-10009-01_060204 System Up Time The relative time since the last reboot of the switch at which this trap occurred. Trap The relevant information of this trap. Note: Trap log information is not retained...
Page 80 - GMRP Learned; show sysinfo
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-14 Switching Commands 202-10009-01_060204 GMRP Learned The value of the corresponding was learned via GMRP and applies to Multicast. Other The value of the corresponding instance does not fall into one of the other categories....
Page 81 - The base object ID for the switch’s enterprise MIB.; Management VLAN Commands; This command configures the Management VLAN ID.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-15 202-10009-01_060204 System Contact Text used to identify a contact person for this switch. May be up to 31 alpha-numeric characters. The factory default is blank. System ObjectID The base object ID for th...
Page 82 - Dot1P Commands; classofservice dot1pmapping; show classofservice dot1pmapping; vlan port priority all
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-16 Switching Commands 202-10009-01_060204 Dot1P Commands classofservice dot1pmapping This command maps an 802.1p priority to an internal traffic class for a device when in ‘Global Config’ mode. The number of available traffic ...
Page 83 - vlan priority; Disabled; show port-channel brief
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-17 202-10009-01_060204 vlan priority This command configures the default 802.1p port priority assigned for untagged packets for a specific interface. The range for the priority is 0-7 Default 0 Format vlan p...
Page 84 - This field displays the name of the port-channel.; Management Commands; Fdbid (Forwarding database ID) indicates which forwarding
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-18 Switching Commands 202-10009-01_060204 Static Capability This field displays whether or not the device has static capability enabled. For each port-channel the following information is displayed: Name This field displays th...
Page 85 - mtu
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-19 202-10009-01_060204 Format no bridge aging-time [fdbid | all] Mode Global Config Forwarding Database ID Fdbid (Forwarding database ID) indicates which forwarding database's aging timeout is being configur...
Page 86 - This command resets the value of MAC address to its default.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-20 Switching Commands 202-10009-01_060204 Format no network javamode Mode Privileged EXEC network mac-address This command sets locally administered MAC addresses. The following rules apply: • Bit 6 of byte 0 (called the U/L b...
Page 87 - network protocol; where; remotecon maxsessions
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-21 202-10009-01_060204 Mode Privileged EXEC network protocol This command specifies the network configuration protocol to be used. If you modify this value change is effective immediately. Default None Forma...
Page 88 - remotecon timeout
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-22 Switching Commands 202-10009-01_060204 remotecon timeout This command sets the remote connection session timeout value, in minutes. A session is active as long as the session has been idle for the value set. A value of 0 in...
Page 89 - serial timeout
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-23 202-10009-01_060204 serial timeout This command specifies the maximum connect time (in minutes) without console activity. A value of 0 indicates that a console can be connected indefinitely. The time rang...
Page 90 - The burned in MAC address used for in-band connectivity.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-24 Switching Commands 202-10009-01_060204 Agetime Displays the address aging timeout for the associated forwarding database in IVL. In an SVL system, this will display the system's address aging timeout value in seconds. show ...
Page 91 - show serial
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-25 202-10009-01_060204 Network Configuration Protocol Current Indicates which network protocol is being used. The options are bootp | dhcp | none. Java Mode Specifies if the switch should allow access to the...
Page 92 - The number of bits in a character. The number of bits is always 8.; This command displays service port configuration information.; Indicates what network protocol was used on; show snmpcommunity; This command displays SNMP community information.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-26 Switching Commands 202-10009-01_060204 38400,57600, and 115200 baud. The factory Default is 9600 baud. Character Size The number of bits in a character. The number of bits is always 8. Flow Control Whether Hardware Flow-Con...
Page 93 - The community string to which this entry grants access. A valid
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-27 202-10009-01_060204 Format show snmpcommunity Mode Privileged EXEC SNMP Community Name The community string to which this entry grants access. A valid entry is a case-sensitive alphanumeric string of up t...
Page 94 - - send traps to the receiver; Disable
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-28 Switching Commands 202-10009-01_060204 Status A pull down menu that indicates the receiver's status(enabled or disabled) and allows the administrator/user to perform actions on this user entry: Enable - send traps to the re...
Page 95 - snmp-server community; snmp-server community ipaddr
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-29 202-10009-01_060204 snmp-server community This command adds (and names) a new SNMP community. A community name is a name associated with the switch and with a set of SNMP managers that manage it with a sp...
Page 96 - This command sets a client IP address for an SNMP community to; snmp-server community ipmask; This command sets a client IP mask for an SNMP community to; snmp-server community mode
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-30 Switching Commands 202-10009-01_060204 no snmp-server community ipaddr This command sets a client IP address for an SNMP community to 0.0.0.0 . The name is the applicable community name. Format no snmp-server community ipad...
Page 97 - snmp-server community ro; This command enables the Authentication Flag.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-31 202-10009-01_060204 Mode Global Config no snmp-server community mode This command deactivates an SNMP community. If the community is disabled, no SNMP requests using this community are accepted. In this c...
Page 98 - snmp-server enable traps bcaststorm; This command disables Link Up/Down traps for the entire switch.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-32 Switching Commands 202-10009-01_060204 Mode Global Config snmp-server enable traps bcaststorm This command enables the broadcast storm trap. When enabled, broadcast storm traps are sent only if the broadcast storm recovery ...
Page 99 - snmp-server enable traps multiusers; This command disables Multiple User traps.; snmp-server enable traps stpmode
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-33 202-10009-01_060204 snmp-server enable traps multiusers This command enables Multiple User traps. When the traps are enabled, a Multiple User Trap is sent when a user logs in to the terminal interface (EI...
Page 100 - This command deletes trap receivers for a community.; snmptrap ipaddr; snmptrap mode
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-34 Switching Commands 202-10009-01_060204 Mode Global Config no snmptrap This command deletes trap receivers for a community. Format no snmptrap <name> <ipaddr> Mode Global Config snmptrap ipaddr This command assig...
Page 101 - telnet; HTTP Commands; This command is used to reset the sslt port to the default value.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-35 202-10009-01_060204 telnet This command regulates new telnet sessions. If sessions are enabled, new telnet sessions can be established until there are no more sessions available. If sessions are disabled,...
Page 104 - This command is used to disable SSH.; ip ssh protocol; This command displays the ssh settings.; This field specifies the current ssh connections.; Device Configuration Commands; addport
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-38 Switching Commands 202-10009-01_060204 no ip ssh This command is used to disable SSH. Format no ip ssh Mode Privileged EXEC ip ssh protocol This command is used to set or remove protocol levels (or versions) for SSH. Either...
Page 105 - This command disables automatic negotiation on a port.; delete interface; removes all configured port-
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-39 202-10009-01_060204 Format addport <logical slot/port> Mode Interface Config auto-negotiate This command enables automatic negotiation on a port. The default value is enable. Format auto-negotiate M...
Page 106 - deleteport; monitor session
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-40 Switching Commands 202-10009-01_060204 deleteport This command deletes the port from the port-channel (LAG). The interface is a logical slot and port number of a configured port-channel. Format deleteport <logical slot/p...
Page 107 - monitor session mode; port lacpmode
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-41 202-10009-01_060204 monitor session mode This command configures the monitor session (port monitoring) mode to enable. The probe and monitored ports must be configured before monitor session (port monitor...
Page 108 - port-channel adminmode; port-channel linktrap
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-42 Switching Commands 202-10009-01_060204 no port lacpmode all This command disables Link Aggregation Control Protocol (LACP) on all ports. Format no port lacpmode all Mode Global Config port-channel This command configures a ...
Page 109 - every configured port-; protocol group; from this protocol-based VLAN group that is identified by
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-43 202-10009-01_060204 Default Enabled Format port-channel linktrap {<logical slot/port> | all} Mode Global Config no port-channel linktrap This command disables link trap notifications for the port-ch...
Page 110 - protocol vlan group
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-44 Switching Commands 202-10009-01_060204 protocol vlan group This command adds the physical <slot/port> interface to the protocol-based VLAN identified by <groupid>. A group may have more than one interface associ...
Page 111 - set garp timer join; set garp timer join all
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-45 202-10009-01_060204 set garp timer join This command sets the GVRP join time per port and per GARP. Join time is the interval between the transmission of GARP Protocol Data Units (PDUs) registering (or re...
Page 112 - set garp timer leave; This command has an effect only when GVRP is enabled.; set garp timer leave all; This command has an effect only when GVRP is enabled.; This command has an effect only when GVRP is enabled.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-46 Switching Commands 202-10009-01_060204 set garp timer leave This command sets the GVRP leave time per port. Leave time is the time to wait after receiving an unregister request for a VLAN or a multicast group before deletin...
Page 113 - set garp timer leaveall; set garp timer leaveall all
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-47 202-10009-01_060204 Mode Global Config set garp timer leaveall This command sets how frequently Leave All PDUs are generated per port. A Leave All PDU indicates that all registrations will be unregistered...
Page 114 - set gmrp adminmode
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-48 Switching Commands 202-10009-01_060204 no set garp timer leaveall all This command sets how frequently Leave All PDUs are generated for all ports to 1000 centiseconds (10 seconds). Note: This command has an effect only when...
Page 115 - set gmrp interfacemode all; set gvrp adminmode; This command enables GVRP.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-49 202-10009-01_060204 no set gmrp interfacemode This command disables GARP Multicast Registration Protocol on a selected interface. If an interface which has GARP enabled is enabled for routing or is enlist...
Page 116 - This command disables GVRP.; set gvrp interfacemode
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-50 Switching Commands 202-10009-01_060204 no set gvrp adminmode This command disables GVRP. Format no set gvrp adminmode Mode Privileged EXEC set gvrp interfacemode This command enables GVRP (GARP VLAN Registration Protocol) f...
Page 117 - The IGMP application supports the following:; set igmp
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-51 202-10009-01_060204 set igmp This command enables IGMP Snooping on the system. The default value is disable. Note: The IGMP application supports the following: • Global configuration or per interface conf...
Page 118 - set igmp groupmembershipinterval
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-52 Switching Commands 202-10009-01_060204 set igmp groupmembershipinterval This command sets the IGMP Group Membership Interval time on the system. The Group Membership Interval time is the amount of time in seconds that a swi...
Page 119 - set igmp maxresponse
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-53 202-10009-01_060204 set igmp maxresponse This command sets the IGMP Maximum Response time on the system. The Maximum Response time is the amount of time in seconds that a switch will wait after sending a ...
Page 120 - show gmrp configuration
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-54 Switching Commands 202-10009-01_060204 Format show garp Mode Privileged EXEC and User EXEC GMRP Admin Mode This displays the administrative mode of GARP Multicast Regis-tration Protocol (GMRP) for the system. GVRP Admin Mod...
Page 121 - how gvrp configuration
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-55 202-10009-01_060204 Port, per-GARP participant basis. The Leave All Period Timer is set to a random value in the range of LeaveAllTime to 1.5*LeaveAllTime. Permissible values are 200 to 6000 centisec-onds...
Page 122 - how igmpsnooping
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-56 Switching Commands 202-10009-01_060204 seconds). The factory default is 60 centiseconds (0.6 seconds). The finest granularity of specification is 1 centisecond (0.01 sec-onds). LeaveAll Timer This Leave All Time controls ho...
Page 123 - If a query is not received on an interface; The text description of this multicast table entry.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-57 202-10009-01_060204 Max Response Time This displays the amount of time the switch will wait after send-ing a query on an interface because it did not receive a report for a particular group on that interf...
Page 125 - Is the MAC Address of the static MAC filter entry.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-59 202-10009-01_060204 Component The component that is responsible for this entry in the Multicast Forwarding Database. Possible values are IGMP Snooping, GMRP, and Static Filtering. Description The text des...
Page 126 - This displays the largest number of entries that have been; is the slot/port that is configured as the monitored port. If this
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-60 Switching Commands 202-10009-01_060204 displayed as 8 bytes. In an SVL system, the MAC address will be displayed as 6 bytes. Type This displays the type of the entry. Static entries are those that are configured by the end ...
Page 127 - show port; Mon; show port protocol
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-61 202-10009-01_060204 show port This command displays port information. Format show port {<slot/port> | all} Mode Privileged EXEC slot/port The physical slot and physical port. Type If not blank, this...
Page 129 - show vlan; Include
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-63 202-10009-01_060204 Active Ports This field lists the ports that are actively participating in the port-channel (LAG). show storm-control This command displays switch configuration information. Format sho...
Page 131 - show vlan port; This command displays VLAN port information.; Specifies the types of frames that may be received on this port.; May be enabled or disabled.; This command disables a port.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-65 202-10009-01_060204 show vlan port This command displays VLAN port information. Format show vlan port {<slot/port> | all} Mode Privileged EXEC and User EXEC slot/port Indicates by slot id and port n...
Page 132 - shutdown all
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-66 Switching Commands 202-10009-01_060204 Mode Interface Config no shutdown This command enables a port. Format no shutdown Mode Interface Config shutdown all This command disables all ports. Default Enabled Format shutdown al...
Page 133 - snmp trap link-status all; This command enables link status traps for all interfaces.; The mode is one of the following:
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-67 202-10009-01_060204 Mode Interface Config snmp trap link-status all This command enables link status traps for all interfaces. Note: This command is valid only when the Link Up/Down Flag is enabled (see “...
Page 134 - spanning-tree bpdumigrationcheck; speed; speed all
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-68 Switching Commands 202-10009-01_060204 spanning-tree bpdumigrationcheck This command enables BPDU migration check on a given interface. The all option enables BPDU migration check on all interfaces. Format spanning-tree bpd...
Page 135 - Acceptable values are:; storm-control broadcast; no storm-control broadcast; This command disables broadcast storm recovery mode.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-69 202-10009-01_060204 Mode Global Config Acceptable values are: 100h 100BASE-T half-duplex 100f 100BASE-T full duplex 10h 10BASE-T half duplex 10f 100BASE-T full duplex storm-control broadcast This command ...
Page 136 - storm-control flowcontrol; This command enables 802.3x flow control for the switch.; vlan
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-70 Switching Commands 202-10009-01_060204 Format no switchconfig storm-control broadcast Mode Global Config storm-control flowcontrol This command enables 802.3x flow control for the switch. Note: This command only applies to ...
Page 137 - vlan acceptframe; This command sets the frame acceptance mode per interface to; Admit All; vlan ingressfilter
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-71 202-10009-01_060204 no vlan This command deletes an existing VLAN. The ID is a valid VLAN identification number (ID 1 is reserved for the default VLAN). VLAN range is 2-4094. Format no vlan <2-4094>...
Page 138 - vlan makestatic; vlan name; vlan participation
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-72 Switching Commands 202-10009-01_060204 no vlan ingressfilter This command disables ingress filtering. If ingress filtering is disabled, frames received with VLAN IDs that do not match the VLAN membership of the receiving in...
Page 139 - vlan participation all; Participation options are:
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-73 202-10009-01_060204 Format vlan participation {exclude | include | auto} <1-4094> Mode Interface Config Participation options are: include The interface is always a member of this VLAN. This is equi...
Page 140 - vlan port acceptframe all; This command sets the frame acceptance mode for all interfaces to; vlan port ingressfilter all
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-74 Switching Commands 202-10009-01_060204 vlan port acceptframe all This command sets the frame acceptance mode for all interfaces. For VLAN Only mode, untagged frames or priority frames received on this interface are discarde...
Page 141 - vlan port pvid all; This command changes the VLAN ID for all interface.; This command sets the VLAN ID for all interfaces to 1.; vlan port tagging all; vlan protocol group
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-75 202-10009-01_060204 vlan port pvid all This command changes the VLAN ID for all interface. Default 1 Format vlan port pvid all <1-4094> Mode Global Config no vlan port pvid all This command sets the...
Page 142 - vlan protocol group add protocol; This command changes the VLAN ID per interface.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-76 Switching Commands 202-10009-01_060204 Mode Global Config vlan protocol group add protocol This command adds the <protocol> to the protocol-based VLAN identified by <groupid>. A group may have more than one prot...
Page 143 - This command sets the VLAN ID per interface to 1.; vlan tagging; Spanning Tree Commands
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-77 202-10009-01_060204 no vlan pvid This command sets the VLAN ID per interface to 1. Format no vlan pvid <1-4094> Mode Interface Config vlan tagging This command configures the tagging behavior for a ...
Page 145 - show spanning-tree interface; show spanning-tree mst detailed
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-79 202-10009-01_060204 show spanning-tree interface This command displays the settings and parameters for a specific switch port within the common and internal spanning tree. The <slot/port> is the des...
Page 146 - show spanning-tree mst port detailed
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-80 Switching Commands 202-10009-01_060204 Designated Root Identifier of the Regional Root for this multiple spanning tree instance. Root Path Cost Path Cost to the Designated Root for this multiple spanning tree instance Root ...
Page 147 - show spanning-tree mst port summary
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-81 202-10009-01_060204 Port Identifier The port identifier for this port within the CST. Port Priority The priority of the port within the CST. Port Forwarding State The forwarding state of the port within t...
Page 148 - show spanning-tree mst summary
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-82 Switching Commands 202-10009-01_060204 Slot/Port The interface being displayed Type Currently not used. STP State The forwarding state of the port in the specified spanning tree instance Port Role The role of the specified ...
Page 149 - show spanning-tree vlan; spanning-tree configuration name
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-83 202-10009-01_060204 Configuration Digest Key Calculated value. Configuration Format Selector Configured value. MST Instances List of all multiple spanning tree instances configured on the switch show span...
Page 150 - spanning-tree configuration revision
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-84 Switching Commands 202-10009-01_060204 Default The base MAC address displayed using hexadecimal notation as specified in IEEE 802 standard. Format spanning-tree configuration name <name> Mode Global Config no spanning...
Page 151 - spanning-tree forceversion
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-85 202-10009-01_060204 no spanning-tree edgeport This command specifies that this port is not an Edge Port within the common and internal spanning tree. Format no spanning-tree edgeport Mode Interface Config...
Page 153 - Default
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-87 202-10009-01_060204 no spanning-tree max-age This command sets the Bridge Max Age parameter for the common and internal spanning tree to the default value, i.e. 20. Format no spanning-tree max-age Mode Gl...
Page 154 - spanning-tree mst instance; spanning-tree mst priority
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-88 Switching Commands 202-10009-01_060204 If the ‘cost’ token is specified, this command sets the path cost for this port within a multiple spanning tree instance or the common and internal spanning tree instance, depending on...
Page 155 - spanning-tree mst vlan
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-89 202-10009-01_060204 If 0 (defined as the default CIST ID) is passed as the <mstid>, then this command sets the Bridge Priority parameter to a new value for the common and internal spanning tree. The...
Page 156 - spanning-tree port mode; User Account Management Commands
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-90 Switching Commands 202-10009-01_060204 Mode Global Config spanning-tree port mode This command sets the Administrative Switch Port State for this port to enabled. Default Disabled Format spanning-tree port mode Mode Interfa...
Page 157 - disconnect; This command closes a telnet session.; Login Session ID
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-91 202-10009-01_060204 disconnect This command closes a telnet session. Format disconnect {<sessionID> | all} Mode Privileged EXEC show loginsession This command displays current telnet and serial port...
Page 158 - users name
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-92 Switching Commands 202-10009-01_060204 Access Mode Shows whether the operator is able to change parameters on the switch (Read/Write) or is only able to view them (Read Only). As a factory default, admin has Read/Write acce...
Page 159 - users passwd; readwrite
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-93 202-10009-01_060204 users passwd This command changes the password of an existing operator. User password should not be more than eight characters in length. If a user is authorized for authentication or ...
Page 160 - users snmpv3 authentication; users snmpv3 encryption; none
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-94 Switching Commands 202-10009-01_060204 users snmpv3 authentication This command specifies the authentication protocol to be used for the specified login user. The valid authentication protocols are none , md5 or sha . If md...
Page 161 - Security Commands; authentication login; no authentication login
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-95 202-10009-01_060204 Security Commands This section describes commands used for configuring security settings for login users and port users. authentication login This command creates an authentication log...
Page 162 - clear dot1x statistics
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-96 Switching Commands 202-10009-01_060204 Format no authentication login <listname> Mode Global Config clear dot1x statistics This command resets the 802.1x statistics for the specified port or for all ports. Format clea...
Page 163 - dot1x login; Config
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-97 202-10009-01_060204 dot1x login This command assigns the specified authentication login list to the specified user for 802.1x port security. The <user> parameter must be a configured user and the &l...
Page 164 - dot1x port-control All
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-98 Switching Commands 202-10009-01_060204 Default auto Format dot1x port-control {force-unauthorized | force-authorized | auto} Mode Interface Config no dot1x port-control This command sets the authentication mode to be used o...
Page 165 - dot1x re-authenticate
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-99 202-10009-01_060204 dot1x re-authenticate This command begins the re-authentication sequence on the specified port. This command is only valid if the control mode for the specified port is 'auto'. If the ...
Page 166 - dot1x timeout
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-100 Switching Commands 202-10009-01_060204 Mode Global Config dot1x timeout This command sets the value, in seconds, of the timer used by the authenticator state machine on this port. Depending on the token used and the value ...
Page 167 - dot1x user; This command is used to enable the RADIUS accounting function.; radius accounting mode
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-101 202-10009-01_060204 no dot1x timeout This command sets the value, in seconds, of the timer used by the authenticator state machine on this port to the default values. Depending on the token used, the cor...
Page 168 - radius server host; no radius server host
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-102 Switching Commands 202-10009-01_060204 radius server host This command is used to configure the RADIUS authentication and accounting server. If the 'auth' token is used, the command configures the IP address to use to conn...
Page 169 - radius server key; radius server msgauth; radius server primary; radius server retransmit
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-103 202-10009-01_060204 radius server key This command is used to configure the shared secret between the RADIUS client and the RADIUS accounting / authentication server. Depending on whether the 'auth' or '...
Page 170 - radius server timeout; show accounting
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-104 Switching Commands 202-10009-01_060204 Format radius server retransmit <retries> Mode Global Config no radius server retransmit This command sets the maximum number of times a request packet is re-transmitted, when n...
Page 172 - This displays the authentication login listname.; show authentication users; show dot1x
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-106 Switching Commands 202-10009-01_060204 show authentication This command displays the ordered authentication methods for all authentication login lists. Format show authentication Mode Privileged EXEC Authentication Login L...
Page 175 - show dot1x users
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-109 202-10009-01_060204 Last EAPOL Frame Version The protocol version number carried in the most recently received EAPOL frame. Last EAPOL Frame Source The source MAC address carried in the most recently rec...
Page 176 - show radius statistics
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-110 Switching Commands 202-10009-01_060204 Primary Server IP Address Indicates the configured server currently in use for authenti- cation Number of configured servers The configured IP address of the authentication server Max...
Page 177 - The number of RADIUS Access-Request packets retransmitted
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-111 202-10009-01_060204 Access Retransmission The number of RADIUS Access-Request packets retransmitted to this RADIUS authentication server. Access Accepts The number of RADIUS Access-Accept packets, includ...
Page 178 - users defaultlogin; users login; must be a configured <; System Utilities; This section describes system utilities.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-112 Switching Commands 202-10009-01_060204 802.1x Port Security This field displays the authentication login list assigned to the user for 802.1x port security. users defaultlogin This command assigns the authentication login ...
Page 179 - clear counters; clear traplog; This command clears the trap log.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-113 202-10009-01_060204 Mode Privileged EXEC clear counters This command clears the stats for a specified <slot/port> or for all the ports or for the entire switch based upon the argument. Format clear...
Page 180 - and the destination as; copy
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-114 Switching Commands 202-10009-01_060204 clear vlan This command resets VLAN configuration parameters to the factory defaults. Format clear vlan Mode Privileged EXEC copy This command uploads and downloads to/from the switch...
Page 181 - Save configuration changes before logging out.; ping; Series L3 Switch
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Switching Commands 8-115 202-10009-01_060204 copy <url> nvram:sshkey-dsa Mode Privileged EXEC logout This command closes the current telnet connection or resets the current serial connection. Note: Save configuration chang...
Page 183 - Syntax conventions are described in; Routing Commands; This command enables OSPF 1583 compatibility.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-1 202-10009-01_060204 Chapter 9 Routing Commands This chapter provides detailed explanation of the Routing commands. The switch commands are divided by functionality into these different groups: • Show command...
Page 184 - area authentication; area nssa; This command disables nssa from the specified area id.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-2 Routing Commands 202-10009-01_060204 area authentication This command specifies the authentication type to be used for the specified area id. Default none Format area <areaid> authentication {none | simple | encrypt} M...
Page 185 - This command configures the translator role of the NSSA. A value of
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-3 202-10009-01_060204 area nssa default-info-originate This command configures the metric value and type for the default route advertised into the NSSA. The optional metric parameterspecifieds the metric of th...
Page 186 - area range; summarylink; This command deletes a specified area range.; area stub
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-4 Routing Commands 202-10009-01_060204 area nssa translator-stab-intv This command configures the translator stability interval of the NSSA. The stabilityinterval is the period of time that an elected translator continues to p...
Page 187 - This command deletes a stub area for the specified area ID.; area stub summarylsa
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-5 202-10009-01_060204 no area stub This command deletes a stub area for the specified area ID. Format no area <areaid> stub Mode Router OSPF Config area stub summarylsa This command configures the Summar...
Page 188 - area virtual-link authentication
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-6 Routing Commands 202-10009-01_060204 area virtual-link authentication This command configures the authentication type and key for the OSPF virtual interface identified by <areaid> and <neighbor>. The <neighbor...
Page 190 - arp
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-8 Routing Commands 202-10009-01_060204 Mode Router OSPF Config no area virtual-link retransmit-interval This command configures the default retransmit interval for the OSPF virtual interface on the virtual interface identified...
Page 191 - arp cachesize; This command configures the default ARP cache size.; arp dynamicrenew
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-9 202-10009-01_060204 The format is 6 two-digit hexadecimal numbers that are separated by colons, for example 00:06:29:32:81:40. Format arp <ipaddress> <macaddr> Mode Global Config no arp This comm...
Page 192 - arp purge; This command configures the ARP request response timeout.; arp retries
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-10 Routing Commands 202-10009-01_060204 no arp dynamicrenew This command disables ARP component from automatically renewing ARP entries of type dynamic when they age out. Format no arp dynamicrenew Mode Privileged Exec arp pur...
Page 193 - arp timeout; This command configures the ARP entry ageout time.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-11 202-10009-01_060204 Default 4 Format arp retries <0-10> Mode Global Config no arp retries This command configures the default ARP count of maximum request for retries. Format no arp retries Mode Globa...
Page 194 - This command disables the RIP auto-summarization mode.; bootpdhcprelay cidoptmode; bootpdhcprelay disable
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-12 Routing Commands 202-10009-01_060204 no auto-summary This command disables the RIP auto-summarization mode. Format no auto-summary Mode Router RIP Config bootpdhcprelay cidoptmode This command enables the circuit ID option ...
Page 195 - bootpdhcprelay maxhopcount
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-13 202-10009-01_060204 bootpdhcprelay maxhopcount This command configures the maximum allowable relay agent hops for BootP/DHCP Relay on the system. The <hops> parameter has a range of 1 to 16. Default 4...
Page 196 - bootpdhcprelay serverip; gateway; unspecified
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-14 Routing Commands 202-10009-01_060204 bootpdhcprelay serverip This command configures the server IP Address for BootP/DHCP Relay on the system. The <ipaddr> parameter is an IP address in a 4-digit dotted decimal format...
Page 198 - distance ospf
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-16 Routing Commands 202-10009-01_060204 Format no default-metric Mode Router RIP Config enable (OSPF) This command resets the default administrative mode of OSPF in the router (active). Default Enabled Format enable Mode Route...
Page 199 - The range of preference is 0 to 255.; distance rip
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-17 202-10009-01_060204 The range of preference is 0 to 255. Default Intra -- 8; Inter -- 10; Type-1 -- 13; Type-2 -- 150. Format distance ospf {intra | inter | type1 | type2} <0-255> Mode Router OSPF Con...
Page 200 - encapsulation
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-18 Routing Commands 202-10009-01_060204 no distribute-list out This command is used to specify the access list to filter routes received from the source protocol. Format no distribute-list <1-199> out {rip | bgp | static...
Page 201 - This command configures the default external LSDB limit for OSPF.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-19 202-10009-01_060204 Restrictions Routed frames are always Ethernet encapsulated when a frame is routed to a VLAN. exit-overflow-interval This command configures the exit overflow interval for OSPF. It descr...
Page 202 - hostroutesaccept; This command enables the RIP hostroutesaccept mode.; ip address; This command configures an IP address on an interface.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-20 Routing Commands 202-10009-01_060204 hostroutesaccept This command enables the RIP hostroutesaccept mode. Default Enabled Format hostroutesaccept Mode Router RIP Config no hostroutesaccept This command disables the RIP host...
Page 203 - ip ecmpmode
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-21 202-10009-01_060204 ip ecmpmode This command enables ECMP mode on the router. Default Disabled Format ip ecmpmode Mode Global Config no ip ecmpmode This command disables ECMP mode on the router. Format no i...
Page 204 - This command disables Router Discovery on an interface.; ip irdp address
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-22 Routing Commands 202-10009-01_060204 no ip irdp This command disables Router Discovery on an interface. Format no ip irdp Mode Interface Config ip irdp address This command configures the address to be used to advertise the...
Page 205 - ip irdp maxadvertinterval; This command configures the default maximum time, in seconds.; ip irdp minadvertinterval; This command configures thedefault minimum time, in seconds.; ip irdp preference
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-23 202-10009-01_060204 ip irdp maxadvertinterval This command configures the maximum time, in seconds, allowed between sending router advertisements from the interface. The range for maxadvertinterval is 4 to ...
Page 206 - ip netdirbcast; ip ospf; This command enables OSPF on a router interface.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-24 Routing Commands 202-10009-01_060204 Format ip irdp preference <-2147483648-2147483647> Mode Interface Config no ip irdp preference This command configures the default preferability of the address as a default router ...
Page 207 - ip ospf areaid; The default authentication type is none.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-25 202-10009-01_060204 Format no ip ospf Mode Interface Config ip ospf areaid This command sets the OSPF area to which the specified router interface belongs. The value for <areaid> is an IP address, for...
Page 208 - ip ospf cost
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-26 Routing Commands 202-10009-01_060204 ip ospf cost This command configures the cost on an OSPF interface. The <cost> parameter has a range of 1 to 65535. Default 10 Format ip ospf cost <1-5535> Mode Interface Con...
Page 209 - ip ospf hello-interval; , which is the highest router priority.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-27 202-10009-01_060204 ip ospf hello-interval This command sets the OSPF hello interval for the specified interface. The value for <seconds> is a valid positive integer, which represents the length of ti...
Page 210 - ip ospf retransmit-interval
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-28 Routing Commands 202-10009-01_060204 ip ospf retransmit-interval This command sets the OSPF retransmit Interval for the specified interface. The value for <seconds> is the number of seconds between link-state advertis...
Page 211 - ip rip; This command enables RIP on a router interface.; ip rip authentication
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-29 202-10009-01_060204 ip rip This command enables RIP on a router interface. Default Disabled Format ip rip Mode Interface Config no ip rip This command disables RIP on a router interface. Format no ip rip Mo...
Page 212 - ip rip receive version; both; ip rip send version
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-30 Routing Commands 202-10009-01_060204 ip rip receive version This command configures the interface to allow RIP control packets of the specified version(s) to be received. The value for <mode> is one of: rip1 to receiv...
Page 213 - ip route; ip route default; This command causes the static default route to be deleted.; ip route distance
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-31 202-10009-01_060204 ip route This command configures a static route. The <networkaddr> and <nexthopip> are valid ip addresses. The <subnetmask> is a valid subnet mask. The [metric] paramet...
Page 214 - ip routing
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-32 Routing Commands 202-10009-01_060204 Mode Global Config no ip route distance This command sets the default static route preference value in the router. Lower route preference values are preferred when determining the best r...
Page 215 - redistribute; internal
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-33 202-10009-01_060204 no redistribute This command configures OSPF protocol to redistribute routes from the specified source protocol/routers. Format no redistribute {rip | bgp | static | connected} [met- ric...
Page 216 - routing; This command enables routing for an interface.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-34 Routing Commands 202-10009-01_060204 redistribute (RIP) This command configures RIP protocol to redistribute routes from the specified source protocol/routers. Default value for metric not-configured Default value for match...
Page 217 - show arp
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-35 202-10009-01_060204 The current value for this function is displayed under "show ip interface" labeled as "Routing Mode". Default Disabled Format routing Mode Interface Config no routing Thi...
Page 219 - show ip brief; show ip interface
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-37 202-10009-01_060204 show bootpdhcprelay This command displays the BootP/DHCP Relay information. Format show bootpdhcprelay Mode Privileged EXEC and User EXEC Maximum Hop Count Is the maximum allowable relay...
Page 220 - Displays whether forwarding of network-directed; The interface being displayed on the row.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-38 Routing Commands 202-10009-01_060204 IP Address Is an IP address representing the subnet configuration of the router interface. This value was configured into the unit. Subnet Mask Is a mask of the network and host portion ...
Page 221 - show ip irdp
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-39 202-10009-01_060204 Netdir Bcast Indicates if IP forwards net-directed broadcasts on this interface. Possible values are Enable or Disable. MultiCast Fwd Indicates the multicast forwarding administrative mo...
Page 223 - show ip ospf area; Is the area id of the requested OSPF area.; The total number of area border routers reachable within this
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-41 202-10009-01_060204 New LSAs Originated The number of new link-state advertisements that have been orig-inated. LSAs Received The number of link-state advertisements received determined to be new instantiat...
Page 224 - Is the IP address identifying the router ID.; show ip ospf interface
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-42 Routing Commands 202-10009-01_060204 show ip ospf database This command displays the link state database. This command takes no options. The information below will only be displayed if OSPF is enabled. Format show ip ospf d...
Page 225 - The information below will only be displayed if OSPF is enabled.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-43 202-10009-01_060204 Router Priority A number representing the OSPF Priority for the specified inter-face. This is a configured value. Retransmit Interval A number representing the OSPF Retransmit Interval f...
Page 226 - show ip ospf interface stats
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-44 Routing Commands 202-10009-01_060204 OSPF Area ID Represents the OSPF Area Id for the specified interface. This is a configured value. Router Priority A number representing the OSPF Priority for the specified inter-face. Th...
Page 227 - The number of LSAs originated.; show ip ospf neighbor; Is a 4-digit dotted-decimal number identifying neighbor router.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-45 202-10009-01_060204 Neighbor Events The number of times this neighbor relationship has changed state, or an error has occurred. External LSA Count The number of external (LS type 5) link-state advertisement...
Page 228 - Is an integer representing the current length of the; show ip ospf neighbor brief; Is an IP address representing the neighbor interface.; show ip ospf range
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-46 Routing Commands 202-10009-01_060204 Exchange start - the first step in creating an adjacency between the two neighboring routers, the goal is to decide which router is the master and to decide upon the initial DD sequence ...
Page 229 - show ip ospf virtual-link
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-47 202-10009-01_060204 Format show ip ospf range <areaid> Mode Privileged EXEC and User EXEC Area ID Is the area id of the requested OSPF area. IP Address Is an IP Address which represents this area rang...
Page 230 - show ip rip
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-48 Routing Commands 202-10009-01_060204 Hello Interval Is the configured hello interval for the OSPF virtual interface. Dead Interval Is the configured dead interval for the OSPF virtual interface. Iftransit Delay Interval Is ...
Page 232 - The total number of routes.; show ip route bestroutes; Is an IP route prefix for the destination.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-50 Routing Commands 202-10009-01_060204 show ip route This command causes the entire route table to be displayed. This commands takes no options. Format show ip route Mode Privileged EXEC and User EXEC Network Address Is an IP...
Page 233 - show ip route entry
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-51 202-10009-01_060204 show ip route entry This command displays detailed information about the route to a specific network to be displayed. The value for <networkaddr> is a valid IP address. Format show...
Page 234 - show ip vlan; Is the MAC Address associated with the; show router rip interface
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-52 Routing Commands 202-10009-01_060204 show ip stats This command displays IP statistical information. Refer to RFC 1213 for more information about the fields that are displayed. This command takes no options. Format show ip ...
Page 235 - Displays the admin mode for VRRP functionality on the switch.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-53 202-10009-01_060204 Receive version The RIP version(s) allowed when receiving updates from the specified interface. The types are none, RIP-1, RIP-2, Both. This is a configured value. RIP Admin Mode RIP adm...
Page 236 - show ip vrrp interface
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-54 Routing Commands 202-10009-01_060204 Router Version Errors Represents the total number of VRRP packets received with Unknown or unsupported version number. Router VRID Errors Represents the total number of VRRP packets rece...
Page 237 - show ip vrrp interface stats
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-55 202-10009-01_060204 show ip vrrp interface stats This command displays the statistical information about each virtual router configured on the 7300 Series L3 Switch. Format show ip vrrp interface stats <...
Page 238 - trapflags
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-56 Routing Commands 202-10009-01_060204 split-horizon This command sets the RIP split horizon mode. Default simple Format split-horizon {none | simple | poison} Mode Router RIP Config no split-horizon This command sets the def...
Page 239 - ip vrrp; There is no default value for vrID.; ip vrrp authentication; The default value for authorization type is No authorization.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-57 202-10009-01_060204 Format no vlan routing <vlanid> Mode VLAN Database ip vrrp This command sets the virtual router ID on an interface for Virtual router configuration in the router. The parameter <...
Page 240 - ip vrrp mode
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-58 Routing Commands 202-10009-01_060204 Mode Interface Config ip vrrp This command enables the administrative mode of VRRP in the router. Default Enabled Format ip vrrp Mode Global Config no ip vrrp This command disables the d...
Page 241 - ip vrrp ip; There is no default value for ipaddress.; ip vrrp preempt; ip vrrp priority
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Routing Commands 9-59 202-10009-01_060204 ip vrrp ip This command sets the ipaddress value for a virtual router. The value for <ipaddr> is the IP Address which is to be configured on that interface for VRRP. The parameter ...
Page 242 - ip vrrp timers advertise
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-60 Routing Commands 202-10009-01_060204 no ip vrrp priority This command sets the default priority value for the virtual router configured on a specified interface. Format no ip vrrp <vrID> priority Mode Interface Config...
Page 244 - nested class support limited to:; General Commands
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-2 CLI Commands: Differentiated Services 202-10009-01_060204 Note that the type of class - all, any, or acl - has a bearing on the validity of match criteria specified when defining the class. A class type of 'any' processes i...
Page 245 - Class Commands; The CLI command root is
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software CLI Commands: Differentiated Services 10-3 202-10009-01_060204 diffserv This command sets the DiffServ operational mode to active. While disabled, the DiffServ configuration is retained and can be changed, but it is not activate...
Page 246 - at the time of class
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-4 CLI Commands: Differentiated Services 202-10009-01_060204 class-map This command defines a new DiffServ class of type match-all, match-any or match-access-group. The < classname> parameter is a case sensitive alphanum...
Page 247 - match any
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software CLI Commands: Differentiated Services 10-5 202-10009-01_060204 This command may be issued at any time; if the class is currently referenced by one or more policies or by any other class, this deletion attempt shall fail. Format ...
Page 248 - Restrictions; match destination-address mac
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-6 CLI Commands: Differentiated Services 202-10009-01_060204 Restrictions The class types of both < classname> and < refclassname> must be identical (i.e., any vs. any, or all vs. all). A class type of acl is not s...
Page 249 - match dstip; match dstl4port
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software CLI Commands: Differentiated Services 10-7 202-10009-01_060204 Default None Format match [not] destination-address mac <macaddr> <mac- mask> Mode Class-Map Config match dstip This command adds to the specified class ...
Page 250 - match ip dscp; value is specified as either an integer from; tosbits; match ip precedence
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-8 CLI Commands: Differentiated Services 202-10009-01_060204 Format match [not] dstl4port {<portkey> | <0-65535> [<0- 65535>]} Mode Class-Map Config match ip dscp This command adds to the specified class defi...
Page 251 - match ip tos; match protocol; ip
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software CLI Commands: Differentiated Services 10-9 202-10009-01_060204 Mode Class-Map Config match ip tos This command adds to the specified class definition a match condition based on the value of the IP TOS field in a packet, which is...
Page 252 - The optional; match source-address mac; parameter is any layer 2 MAC address formatted as six, two-; match srcip; parameter; match srcl4port
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-10 CLI Commands: Differentiated Services 202-10009-01_060204 The optional [ not] parameter has the effect of negating this match condition for the class (i.e., match all IP Protocol numbers except for the one specified here)....
Page 253 - is one of the; end of a port range.; match vlan; VLAN Identifier values except for what is specified here).; Policy Commands
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software CLI Commands: Differentiated Services 10-11 202-10009-01_060204 To specify the match condition as a single keyword notation, the value for < portkey> is one of the supported port name keywords (listed below). The currently...
Page 254 - Traffic Conditioning; bandwidth kbps; a particular direction.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-12 CLI Commands: Differentiated Services 202-10009-01_060204 Traffic Conditioning Specify traffic conditioning actions (policing, marking, shaping) to apply to traffic classes Service Provisioning Specify bandwidth and queue ...
Page 255 - bandwidth percent
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software CLI Commands: Differentiated Services 10-13 202-10009-01_060204 successful attachment of a policy to the interface, or shall cause this command to fail if the policy is already in service on one or more interfaces. Policy Type O...
Page 256 - is the names of an existing DiffServ class. Note that this command
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-14 CLI Commands: Differentiated Services 202-10009-01_060204 Note: The CLI mode is changed to Policy-Class-Map Config when this command is successfully executed. Format class <classname> Mode Policy-Map Config no class ...
Page 257 - value is required and is specified as either an integer from 0 to; Service Commands
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software CLI Commands: Differentiated Services 10-15 202-10009-01_060204 police-simple This command is used to establish the traffic policing style for the specified class. The simple form of the police command uses a single data rate an...
Page 258 - This set of commands consists of service addition/removal.; can be used in the; mode to attach this policy to all system interfaces. The direction
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-16 CLI Commands: Differentiated Services 202-10009-01_060204 The service commands attach a defined policy to a directional interface. Only one policy may be assigned at any one time to an interface in a particular direction. ...
Page 259 - Show Commands
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software CLI Commands: Differentiated Services 10-17 202-10009-01_060204 Format no service-policy {in | out} <policymapname> Mode Global Config (for all system interfaces) Mode Interface Config (for a specific interface) Show Comma...
Page 260 - This field displays the values of the Match Criteria.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-18 CLI Commands: Differentiated Services 202-10009-01_060204 Match Criteria The Match Criteria fields will only be displayed if they have been configured. They will be displayed in the order entered by the user. These are eva...
Page 264 - show diffserv service
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-22 CLI Commands: Differentiated Services 202-10009-01_060204 Random Drop Maximum Drop Probability This field displays the RED maximum drop probability.This is not displayed if the queue depth management scheme is not RED. Ran...
Page 265 - show diffserv service brief; The traffic direction of this interface service, either in or out; show policy-map interface; parameter specifies a valid slot number and port number for the; A cumulative count of the octets/packets offered to
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software CLI Commands: Differentiated Services 10-23 202-10009-01_060204 show diffserv service brief This command displays all interfaces in the system to which a DiffServ policy has been attached. The direction parameter is optional; if...
Page 267 - supported counters are shown in the display output.; and; The traffic direction of this interface service, either in or out.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software CLI Commands: Differentiated Services 10-25 202-10009-01_060204 Note: None of the counters listed here are guaranteed to be supported on all platforms. Only supported counters are shown in the display output. show service-policy...
Page 270 - Configuration Commands
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 11-2 CLI Commands: ACL 202-10009-01_060204 Configuration Commands access-list This command creates an Access Control List (ACL) that is identified by the parameter < accesslistnumber>. The ACL number is an integer from 1 t...
Page 273 - DHCP Server Configuration Commands; This command deletes the client identifier.; This command removes the client name.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software DHCP Server Commands 12-1 202-10009-01_060204 Chapter 12 DHCP Server Commands DHCP Server Configuration Commands These commands configure the DHCP Server parameters and address pools. client-identifier This command specifies the...
Page 274 - This command removes the default router list.; This command removes the DNS Server list.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 12-2 DHCP Server Commands 202-10009-01_060204 Format no client-name Mode DHCP Pool Config Mode default-router This command specifies the default router list for a DHCP client. {address1, address2… address8} are valid IP addresse...
Page 275 - host
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software DHCP Server Commands 12-3 202-10009-01_060204 hardware-address This command specifies the hardware address of a DHCP client. Hardware-address is the MAC address of the hardware platform of the client consisting of 6 bytes in dot...
Page 276 - ip dhcp excluded-address; no ip dhcp excluded-address; This command removes the excluded IP addresses for a DHCP client.; ip dhcp ping packets
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 12-4 DHCP Server Commands 202-10009-01_060204 ip dhcp excluded-address This command specifies the IP addresses that a DHCP server should not assign to DHCP clients. Low-address and high-address are valid IP addresses; each made ...
Page 277 - no ip dhcp pool; lease; no lease
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software DHCP Server Commands 12-5 202-10009-01_060204 ip dhcp pool This command configures a DHCP address pool name on a DHCP server and enters DHCP pool configuration mode. Default None Format ip dhcp pool <name> Mode Global Conf...
Page 278 - network; no network; This command removes the subnet number and mask.; service dhcp; no service dhcp; This command disables the DHCP server and relay agent features.; DHCP Server Show Commands
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 12-6 DHCP Server Commands 202-10009-01_060204 network This command is used to configure the subnet number and mask for a DHCP address pool on the server. Network-number is a valid IP address, made up of four decimal bytes rangin...
Page 279 - show ip dhcp binding; show ip dhcp pool configuration
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software DHCP Server Commands 12-7 202-10009-01_060204 show ip dhcp binding This command displays address bindings for the specific IP address on the DHCP server. If no IP address is specified, the bindings corresponding to all the addre...
Page 281 - DHCP Server Clear Commands; clear ip dhcp binding; This command clear DHCP server statistics counters.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software DHCP Server Commands 12-9 202-10009-01_060204 DHCPOFFER The number of DHCPOFFER messages that were sent by the server. DHCPACK The number of DHCPPACK messages that were sent by the server. DHCPNACK The number of DHCPNACK message...
Page 284 - Other NETGEAR products that work with 7300 Series L3 Switch:; poe
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 13-2 FSM7326P Power Over Ethernet Commands 202-10009-01_060204 Attached to the PSE is the UPS. A UPS is connected to each device that requires alternative power. With Power over Ethernet, this function is centralized in a UPS co...
Page 285 - poe priority; low; poe limit; poe usagethreshold; show poe port info; Privilege
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software FSM7326P Power Over Ethernet Commands 13-3 202-10009-01_060204 poe priority This command sets the priority level for the delivery of power to an attached device. The switch may not be able to supply power to all connected device...
Page 287 - show poe
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software FSM7326P Power Over Ethernet Commands 13-5 202-10009-01_060204 show poe This command displays the total power available and the total power consumed in the system. Format show poe Mode Privilege
Page 289 - Appendix A
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software IS CLI Mapping A-1 202-10009-01_060204 Appendix A IS CLI Mapping This chapter illustrates the mapping between CLI commands and the previous 7300 Series L3 Switch commands. The Package column indicates the 7300 Series L3 Switch p...
Page 335 - Appendix B; Fast Ethernet Cable Guidelines; Certification
Cabling Guidelines B-1 202-10009-01_060204 Appendix B Cabling Guidelines This appendix provides specifications for cables used with a NETGEAR NETGEAR 7300 Series Layer 3 Managed Switch. Fast Ethernet Cable Guidelines Fast Ethernet uses UTP cable, as specified in the IEEE 802.3u standard for 100BASE-...
Page 336 - Category 5 Cable; Category 5 Cable Specifications; Ensure that the fiber cable is crossed over to guarantee link.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software B-2 Cabling Guidelines 202-10009-01_060204 Category 5 Cable Category 5 distributed cable that meets ANSI/EIA/TIA-568-A building wiring standards can be a maximum of 328 feet (ft.) or 100 meters (m) in length, divided as follows:...
Page 337 - Twisted Pair Cables; illustrates straight-through twisted pair cable.; SPECIFICATIONS
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Cabling Guidelines B-3 202-10009-01_060204 Table 13-3. Electrical Requirements of Category 5 Cable Twisted Pair Cables For two devices to communicate, the transmitter of each device must be connected to the receiver of the other...
Page 338 - illustrates crossover twisted pair cable.; Patch Panels and Cables
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software B-4 Cabling Guidelines 202-10009-01_060204 Figure 13-2 illustrates crossover twisted pair cable. Figure 13-2: Crossover Twisted-Pair Cable Patch Panels and Cables If you are using patch panels, make sure that they meet the 100BA...
Page 339 - Using 1000BASE-T Gigabit Ethernet over Category 5 Cable; Cabling; Length
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Cabling Guidelines B-5 202-10009-01_060204 Note: Flat “silver satin” telephone cable may have the same RJ-45 plug. However, using telephone cable results in excessive collisions, causing the attached port to be partitioned or di...
Page 340 - Factors that affect the return loss are:; Patch Cables
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software B-6 Cabling Guidelines 202-10009-01_060204 Unlike 10BASE-T and 100BASE-TX, which use only two of the four pairs of wires within the Category 5, 1000BASE-T uses all four pairs of the twisted pair. Make sure all wires are tested ⎯...
Page 341 - PIN
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Cabling Guidelines B-7 202-10009-01_060204 Figure 13-4 shows the RJ-45 plug and RJ-45 connector. Figure 13-4: RJ-45 Plug and RJ-45 Connector with Built-in LEDs Table 13-1 lists the pin assignments for the 10/100 Mbps RJ-45 plug ...
Page 342 - Conclusion
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software B-8 Cabling Guidelines 202-10009-01_060204 Table 13-2. 100/1000 Mbps RJ-45 Plug and RJ-45 Connector Pin Assignments Conclusion For optimum performance of your 1000BASE-T product, it is important to fully qualify your cable insta...
Page 343 - Numeric
Glossary C-1 202-10009-01_060204 Appendix C Glossary Use the list below to find definitions for technical terms used in this manual. Numeric 802.1D The IEEE designator for Spanning Tree Protocol (STP). STP, a link management protocol, is part of the 802.1D standard for media access control bridges. ...
Netgear XAU2511
Manual
Netgear CMD31T-100NAS
Manual
Netgear WPN111
Manual
Netgear DG834 V3
Manual
Netgear WN311B
Manual
Netgear PTV1000
Manual
Netgear EVA8000
Manual
Netgear WPN511
Manual
Netgear Music Player
Manual
Netgear EVA9100
Manual
Netgear XAV1601
Manual
Netgear WN604-100NAS
Manual
Netgear 341U
Manual
Netgear WAG302
Manual
Netgear WG111U
Manual
Netgear WG102NA
Manual
Netgear Pro Business
Manual