NetComm NP2724M - Manuals

NetComm NP2724M – Manual in PDF format online.

Manuals:

Manual

Manual NetComm NP2724M

Summary

Page 3 - Chapter 2; Installation explains the functions of the switch and how to; Chapter 3; Specifications contains information about the cables, and the

1. Introduction Thank you for choosing the NetComm NP2724M 24 port 10/100 + 2 Gigabit VLAN Managed Switch. These switches are a cost-effective switching solution idea for small business and the network edge. It provides Quality of Service (QoS) features, such as 802.1p, DSCP and Rate Control, to ens...

Page 4 - Power

2. Installation This chapter describes the function of the NP2724M switch components and shows how to install it on the desktop or shelf. Basic knowledge of networking is assumed. Read this chapter completely before continuing. 2.1. 2.2. Product Description Overview NP2724M supports 802.1Q VLAN, QoS...

Page 5 - LED Function; POWER; Green; Reset Button; Reset

connection. G1, G2 This is where you connect the Cat. 5e or better Ethernet cable for 10/100/1000 Mbps Ethernet connection miniGBIC This is where you connect the SFP module for fiber connection. Console This is where you connect the RS-232 cable for CLI management. Power This is where you connect th...

Page 6 - Step 2

Figure 2.5.1 Network Configuration for NP2724M (NEED TO REPLACED BY the FRONT PANEL IMAGE of a NP2724 swtich) Read and perform the following procedures to install the switch, Pre-Installation Considerations Gigabit Considerations: If you will use the switch for Gigabit applications, keep in mind tha...

Page 9 - Preparing for configuration; There are four methods to manage your switch:

Configuration This Chapter will describe the use of the NP2724M Management configuration program. 2.7. Preparing for configuration NP2724M offers a console CLI interface for switch configuration and web management. Users can use this interface to perform device configuration. There are four methods ...

Page 10 - Run a terminal emulation program with the following setting.; Logging on to the switch; Enter the factory default user name “; admin; ” with no password when logging

Web-Browser You can manage the switch through a web connection by connecting to the switch’s IP address using your web browser. NP2724M default IP address: http://192.168.1.254 Default User Name: admin Default Password: (blank) This User Guide provides instructions on how to configure the switch usi...

Page 11 - Table 1 CLI Command Modes

Switch. This interface allows you to access the switch using the Web browser of your choice. 2.8.1. Logging on the switch To log on to the Switch: 1. In your web browser, specify the IP address of NP2724M. Default IP address is 192.168.1.254 . 2. Enter the factory default user name: “admin“ and no p...

Page 12 - Interface Config Mode; User Mode commands; help; User Mode; help; User Mode

User Mode When the operator logs into the CLI, the User Mode is the initial mode. The User Mode contains a limited set of commands. The command prompt shown at this level is: Command Prompt: COMMAND> Privileged Mode To have access to the full suite of commands, the operator must enter the Privile...

Page 13 - Privileged Mode commands; port ID

This command is used to exit from the telnet Format logout Mode User Mode ping This command sends echo messages. Format ping < A.B.C.D > Mode User Mode show 1) show port This command displays port status. Format show port {< port# > | all} Mode User Mode 2) show network This command disp...

Page 14 - filename

This command is used to clear static arl table entries Format clear arl static mac < mac-addr > Mode Privileged Mode 4) clear config This command is used to restore switch factory default configuration Format clear config Mode Privileged Mode 5) clear counters This command is used to clear RMO...

Page 21 - Global Config mode commands

This command displays rmon event log. Format show rmon event log event index <1..65535> Mode Privileged Mode 22.6) show rmon history This command displays rmon history. Format show rmon history index <1..65535> Mode Privileged Mode 22.7) show rmon statistics This command displays port rm...

Page 33 - WORD

Format sntp server enable Mode Global Config 3.2) sntp server ipaddr This command sets sntp server IP address. Format sntp server ipaddr < IP-addr > Mode Global Config 3.3) sntp server polling This command sets sntp server polling time interval. Format sntp serve polling < 0-9 > Mode Glo...

Page 38 - Interface Config mode commands

6.4) access-list name <WORD> set IP-mode packet-type This command specifies the packet type. Format access-list name < WORD > set IP-mode packet-type {ICMP|IGMP|IP|TCP|UDP|GRE} Mode Global Config 6.5) access-list name <WORD> set mac-mode Specify ACL entry priority. 6.5.1) access-li...

Page 40 - sourcemac

Mode Interface Config 4.2) 8021 set Status of local-802.1 settings Format lldp tlvs-tx {enable | disable} option 8021 {pvid | vlanname | protocol-id} Mode Interface Config eg.switch(interdface 1)lldp tlvs enable option 8021 pvid 4.3) 8023 set Format lldp tlvs-tx {enable | disable} option 8023 {mac-p...

Page 44 - Interface Config; interface Config

Format poe detection type {0 | 1 | 2 | 3 | 4 | 5} Mode Interface Config 4)high-power This command configures power Energy Mode on a port on Start High Power (Support 30W power device) off End High Power Mode (Support 15.4W power device) Format poe high-power status {enable | disable} Mode interface ...

Page 45 - Category 3 or better, UTP or STP

3. Specifications 3.1. Cable specifications Straight-Through and Crossed-Over Cable Specifications Table Ethernet Type Cable Requirements Maximum Length 10BASE-T Category 3 or better, UTP or STP 328 ft (100M) 100BASE-TX Category 5 or better, UTP or STP 328 ft (100M) 1000BASE-T Category 5e or better,...

Page 47 - Software Specification; Supports 802.1Q VLAN for assigning users to VLAN associated with

3.2. Technical Specifications 3.2.1. Software Specification NP2724M 24 Port 10/100 + 2 Gigabit VLAN Managed Switch □ Four groups (history, statistics, alarms, and events) of embedded remote monitoring (RMON) agents for network monitoring and traffic analysis □ Provides SNMP protocol(v1/v2c/v3) to mo...

Page 48 - Supports web-based interface for management; Hardware Specification; Supports 8K MAC address and Up to 3Mb packet buffer

co-operate with the RADIUS servers. □ Supports broadcast, known-multicast, and unknown uni-cast storm control □ Supports web-based interface for management □ Supports CLI interface for local console or remote Telnet management □ Supports TFTP, HTTP and X-modem protocol for firmware/configuration upg...

Page 49 - Standard Conformance; EMC Certification

Power 100~120/200~240 VAC~1.0 A/0.5 A 50~60Hz Operating Temp. 0 ℃ ~ 40 ℃ (32 ~ 104 ) Storage Temp. -40 ~ 70 (-40 ~ 158 ) Operating Humidity 20% to 85%,relative humidity, non-condensing Storage Humidity 20% to 90%,relative humidity, non-condensing 3.2.4. Standard Conformance EMC Certification FCC Cla...

Page 50 - Customer Information

4. Legal & Regulatory Information This manual is copyright. Apart from any fair dealing for the purposes of private study, research, criticism or review, as permitted under the Copyright Act, no part may be reproduced, stored in a retrieval system or transmitted in any form, by any means, be it ...