Napoleon ZCVF36 - Manuals - manualsarea.com

Page 2 - WARNING; TABLE of CONTENTS; PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE; REPLACEMENTS

2 W415-0527 / 09.29.05 PG 3 INTRODUCTION Warranty 4-6 INSTALLATION & FINISHING General Instructions Hood Installation Gas Connector Locations Framing Nailing Tab Instruction Mantle Clearances 7 OPTIONS Optional Blower Installation WARNING • Under no circumstances should this enclosure be modifi ...

Page 3 - NAPOLEON GAS FIREPLACE PRESIDENT’S LIFETIME LIMITED WARRANTY; rebox enclosure are warranted against defects for as long as you; CONDITIONS AND LIMITATIONS

3 W415-0527/ 09.29.05 NAPOLEON gas fi replaces are manufactured under the strict Standard of the world recognized ISO 9001:2000 Quality Assurance Certi fi cate. NAPOLEON products are designed with superior components and materials, assembled by trained craftsmen who take great pride in their work. T...

Page 4 - Warning: Do not operate without hood in place.; SPECIFICATIONS; FIGURE 1

4 W415-0527 / 09.29.05 GENERAL INSTRUCTIONS THE INSTALLATION MUST CONFORM WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES WITH THE NATIONAL FUEL GAS CODE, ANSI Z223.1 / NFPA 54 AND TO THE NATIONAL ELECTRICAL CODE, ANSI / NFPA 70. Use only accessories designed for and listed with your specifi c fi...

Page 5 - ) identify the preferred inlet and remove corresponding knock; GAS INLET LOCATIONS

5 W415-0527/ 09.29.05 7” 13” There are fi ve gas inlet locations on the ventless fi rebox enclosure. One on each side of the unit, two at the rear, and one on the bottom. Using the following illustrations ( FIGURE 2a-f ) identify the preferred inlet and remove corresponding knock out. 13 1/4” 7” FIG...

Page 6 - FRAMING; FIGURE 3; sides, back, bottom and top of the unit

6 W415-0527 / 09.29.05 ANY CHANGE TO THIS ENCLOSURE CAN BE DANGEROUS AND IS PROHIBITED. It is best to frame your ventless fi rebox enclosure after it is positioned. Use 2x4’s and frame to local building codes. ( FIGURE 3-5 ) FRAMING 21 1/4" 42 1/2” 32 3/4" 21 1/4" 47 1/8” 35 3/4" 52 ...

Page 7 - FIGURE 6c; * Additional set screws may be installed.; NAILING TAB INSTRUCTION; FIGURE 7

7 W415-0527/ 09.29.05 1) Attach the nailing tabs to the corner posts using the 2 sheet metal screws supplied. Secure through the centre of the top and bottom slots in the nailing tab and then through the existing holes in the corner posts. If there are no existing holes, follow these instructions:Po...

Page 8 - OPTIONAL BLOWER INSTALLATION

8 W415-0527 / 09.29.05 Secure to the threaded stud using the lock washer and wing nut provided. Ensure that the blower does not touch the fi rebox base or the fi rebox. ( FIGURE 9 ) Attach the connectors from the black and red wires to the blower. The wire harness provided in this kit is a universal...

Page 9 - WITH THERMAL SWITCH BRACKET; FIGURE 9; THERMAL DISC; FIGURE 9

9 W415-0527/ 09.29.05 1. Remove the hearth pads and the blower access cover. ( FIGURE 9 ) 2. Install the blower using the optional blower installation instructions.3. Pull the black and white thermal disc wires through the 7/8” bushing in the blower access cover.4. Cut the white wire as close to the...

Page 10 - REPLACEMENTS; FOR WARRANTY REPLACEMENT PARTS, A; REPLACEMENT PARTS

10 W415-0527 / 09.29.05 REPLACEMENTS Contact your dealer for questions concerning prices and availability of replacement parts. Normally all parts can be ordered through your Napoleon dealer or distributor. FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE REQUIRED TO HONOU...

Page 11 - This fireplace must be serviced annually depending on usage.

11 W415-0527/ 09.29.05 W olf Steel Fir eplace Ser vice Histor y This fireplace must be serviced annually depending on usage. Date Service T echnician Name Service Performed S pecial Concerns Dealer Name

Page 12 - NOTES