Page 2 - prOpOsitiOn 65 WarninG
page 2 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) prOpOsitiOn 65 WarninG Engine exhaust and some of its constituents, and some dust created of California to cause cancer, birthdefects and other reproductive harm. by power sanding, sawing, grinding, drilling and other...
Page 3 - SILICOSIS WARNING; siliCOsis/respiratOry WarninGs
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 3 Grinding/cutting/drilling of masonry, concrete, metal andother materials with silica in their composition may giveoff dust or mists containing crystalline silica. Silica is abasic component of sand, quartz, brick clay...
Page 4 - table Of COntents; Mixer; Component drawings; NOTICE
page 4 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) table Of COntents WM70sH5C/WM70sH8C Mixer Proposition 65 Warning ........................................... 2 Silicosis/Respiratory Warnings ................................ 3 Table Of Contents .........................
Page 5 - parts OrderinG prOCedures; Ordering parts has never been easier!; Choose from three easy options:; We aCCepT all MaJor CrediT CardS!; order via internet; Order; order via Fax
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 5 parts OrderinG prOCedures www .multiquip .com Ordering parts has never been easier! Choose from three easy options: We aCCepT all MaJor CrediT CardS! When ordering parts, please supply: ❒ dealer account number ❒ deale...
Page 6 - safety infOrMatiOn; SaFeTY MeSSageS; danger; Lethal exhaust gas hazards; Symbol
page 6 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) safety infOrMatiOn Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safety ...
Page 7 - general SaFeTY
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 7 safety infOrMatiOn general SaFeTY CauTion never operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devi...
Page 8 - Mixer SaFeTY
page 8 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) safety infOrMatiOn Mixer SaFeTY danger never operate the equipment in an explosive atmosphere or near combustible materials. An explosion or fi re could result causing severe bodily harm or even death. do noT mix ...
Page 9 - generaTor SaFeTY; power Cord/Cable Safety; TranSporTing SaFeTY
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 9 safety infOrMatiOn Fuel SaFeTY (gaSoline ModelS onlY) danger do noT start the engine near spilled fuel or combustible fl uids. Fuel is extremely fl ammable and its vapors can cause an explosion if ignited. alWaYS ...
Page 10 - ToWing SaFeTY; Department of; environMenTal SaFeTY
page 10 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) safety infOrMatiOn ToWing SaFeTY CauTion Check with your local county or state safety towing regulations, in addition to meeting Department of Transportation (DOT) Safety Towing Regulations, before towing your mixe...
Page 11 - ToW Bar To Mixer ConneCTion; Figure 1. Tow Bar and Safety Chain Installation; CauTion; safety CHain COnneCtiOn
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 11 ToW Bar To Mixer ConneCTion Reference Figure 1 for the installation of the safety chain.1. Insert the tow bar through the round opening at the bottom of the mixer stand. Align the hole on the tow bar with the hole on...
Page 12 - speCifiCatiOns; Table 1. Mixer Specifications
page 12 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) speCifiCatiOns Table 1. Mixer Specifications Capacity 7.0 cu. ft (198 liters) Bag Capacity 1-1/2 to 2-1/2 bags Weight 788 lbs. (357 kg.) Height W/dump Handle 73 in. (185 cm.) discharge Height 21 in. (53 cm.) drive V-...
Page 13 - diMensiOns; description; Width
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 13 diMensiOns Figure 3. Dimensions C A B HBC-1 2-INCH BALL COUPLER HPC-1 1-INCH PIN COUPLER OPTIONAL TOW BARS APPROXIMATE LENGTH 36 IN. (91.44 CM) HLC-1 LOOP COUPLER Table 3. dimensions description dimensions in. (cm) L...
Page 14 - General infOrMatiOn; appliCaTion; Table 4. Hardware Torque recommendations; Figure 4. Mixer Components
page 14 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) General infOrMatiOn appliCaTion The MQ Whiteman WM70SH5C/WM70SH8C mixer (drum capacity of 7.0 cu. ft./198 liters) is shipped completely assembled and has been factory tested and is ready for use.This mixer is only in...
Page 15 - COMpOnents
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 15 COMpOnents Figure 4 illustrates the basic components and controls of the WM70SH5C/WM70SH8C mixer.1. Tires ply — The tire ply (layers) number is rated in letters. This mixer uses 13-inch 4-ply tires. 2. engine Cover —...
Page 16 - inspeCtiOn; BeFore STarTing; Season; Summer
page 16 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) inspeCtiOn BeFore STarTing 1. Read all safety instructions at the beginning of manual.2. Clean the unit, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner. 3. Check the air...
Page 17 - Fuel CHeCk
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 17 inspeCtiOn Fuel CHeCk 1. Remove the gasoline cap located on top of fuel tank.2. Visually inspect to see if fuel level is low. If fuel is low, replenish with unleaded fuel. 3. When refueling, be sure to use a strainer...
Page 18 - Figure 7. Engine Components; iniTial ServiCing; basiC enGine
page 18 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) Figure 7. Engine Components iniTial ServiCing The engine (Figure 7) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the engine manufacturer’s manual for instructions and detai...
Page 19 - paddle blade adjustMent; Adjust paddles as shown in Figure 8.; Figure 8. Paddle Blade Adjustment; DRUM END
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 19 paddle blade adjustMent Adjust paddles as shown in Figure 8. Figure 8. Paddle Blade Adjustment TOW ENDCAST PADDLE ENGINE ENDCAST PADDLE CENTER ENGINE END CAST PADDLE SIDE PADDLE BLADE END P ADDLE BLADE ROTATION ROT A...
Page 20 - do noT use your; Figure 10. Choke Lever; Warning; Figure 11. Throttle Lever
page 20 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) start-up This section is intended to assist the operator with the initial start-up of the unit. It is extremely important that this section be read carefully before attempting to use the mixer in the field. do noT us...
Page 21 - Figure 14. Belt Slip Lever; Figure 17. Starter Grip
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 21 start-up 6. Place the belt slip lever (Figure 14) in the START/STOP (disengaged) position. Figure 14. Belt Slip Lever (Start/Stop Position) Figure 15. Drum Lock Pin (Side-View) START/STOP POSITION BELT SLIP LEVER Cau...
Page 22 - OperatiOn; Figure 20. Stand Clear of Dump Handle; STopping THe Mixer; STAND CLEAR OF DUMP HANDLE.
page 22 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) OperatiOn Mixing/duMping 1. The paddle shaft inside the drum should be rotating at this time. 2. Add a small amount water to the mixing drum. 3. Lift the mixing bag compound onto the steel safety grate over the bag c...
Page 23 - nOtes
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 23 nOtes
Page 24 - Table 6. engine Maintenance Schedule
page 24 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) MaintenanCe (enGine) Use Table 6 as a general maintenance guideline when servicing your engine. For more detail engine maintenance information, refer to the engine owner’s manual supplied with your engine. Table 6. e...
Page 25 - Figure 21. Spark Plug Gap; engine oil; GAP; engine air Cleaner; Figure 23. Engine Air Cleaner
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 25 MaintenanCe (enGine) Perform the scheduled maintenance procedures as defined by Table 6 and below: dailY Thoroughly remove dirt and oil from the engine and control area. Clean or replace the air cleaner elements as...
Page 27 - WHeel BearingS; Figure 27. Wheel Hub and Bearings; Main gear and drive pinion alignMenT; Figure 28. Drive Pinion and Main Gear
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 27 MaintenanCe (Mixer) Figure 26. Grease Fittings (Countershaft) WHeel BearingS 1. After every 3 months of operation, remove the hub dust cap and inspect the wheel bearings (Figure 27). Once a year, or when required, di...
Page 28 - Figure 29. Gear Teeth Alignment; gear luBriCaTion; Figure 30. Pinion and Bull Gear Lubrication
page 28 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) inSpeCT TooTH ConTaCT BeTWeen Main gear and drive pinion 1. Coat 3 or 4 teeth at 3 different positions on the main gear with yellow paint. 2. Rotate the drive pulley in both directions.3. Inspect the tooth pattern.4....
Page 29 - lug nut Torque requirements; do noT; Table 7. Tire Wear Troubleshooting; never use an pneumatic air gun to tighten wheel; Figure 31. Wheel Lug Nuts Tightening
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 29 MaintenanCe (Mixer) lug nut Torque requirements It is extremely important to apply and maintain proper wheel mounting torque. Be sure to use only the fasteners matched to the cone angle of the wheel. Proper procedure...
Page 30 - SuSpenSion; Figure 32. Axle Support Components; Mixer Cleaning; alWaYS disconnect the spark plug wire (gasoline; Figure 33. No Spraying of Water; CRUSH HAZARD AREA. KEEP HANDS
page 30 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) MaintenanCe (Mixer) SuSpenSion The rigid type axle and associated hardware (Figure 32) should be periodically inspected for signs of excessive wear, elongation of bolt holes, and loosening of fasteners. Replace all d...
Page 31 - Mixer STorage
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 31 MaintenanCe (Mixer) Mixer STorage For storage of the mixer for over 30 days, the following is recommended: Drain the fuel tank completely, or add STA-BIL to the fuel. Run the engine until the fuel is completely c...
Page 32 - trOublesHOOtinG; Symptom
page 32 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) trOublesHOOtinG Troubleshooting (engine) Symptom possible problem Solution Diffi cult to start, fuel is available, but no spark at spark plug. Spark plug bridging? Check gap, insulation or replace spark plug. Carbon ...
Page 34 - Mixer Troubleshooting
page 34 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) Mixer Troubleshooting Blades will not rotate. Worn or defective V-belt? Replace V-belt. Adjustment lever mis-aligned? Check position of adjustment lever. Adjust if necessary. Material leaking from drum ends. Worn or ...
Page 35 - WirinG diaGraM
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 35 WirinG diaGraM
Page 36 - explanatiOn Of COde in reMarks COluMn; SaMple parTS liST; reMarkS Column
page 36 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) explanatiOn Of COde in reMarks COluMn The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are ...
Page 37 - suGGested spare parts
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 37 suGGested spare parts WM70SH5C/WM70SH8C plaSTer and MorTar Mixer WiTH Honda gx160/gx240 engine 1 to 3 units Qty. p/n description 6............505834 .................. V-BELT 2............EM914288 ............ OIL SE...
Page 38 - naMeplate and deCals
page 38 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) naMeplate and deCals INSTRUCTIONSDE SÉCURITÉ 1. Lire le manuel du propriétaire avant d'opérer. 2. Garder les personnes non autorisées et non formées loin de la machinelorsqu'elle est en marche. 3. S'assurer que tous ...
Page 39 - CIP520938 DECAL, READ MANUAL, CRUSH HAZARD
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 39 naMeplate and deCals no. parT no. parT naMe QTY. reMarkS 1 EM948630 DECAL, PUSH TO STOP (ENGLISH) 1 2 CIP520932 DECAL, PUSH TO STOP (FRENCH) 1 3 CIP520933 DECAL, DO NOT SMOKE 1 4 CIP520938 DECAL, READ MANUAL, CRUSH H...
Page 40 - OPTIONAL TOW BARS
page 40 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) fraMe assy. MOUNT PILLOW BLOCKS FOR PINION SHAFT HERE MOUNT DRUM BEARING HERE MOUNT DRUM BEARING HERE OPTIONAL TOW BARS A A 1 2 10 3 4 8 9 5 11 12 13 15 16 17 18 14 7 CHAIN & LINK KIT 14A
Page 43 - PADDLE SHAFT
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 43 paddle sHaft assy. no. parT no. parT naMe QTY. reMarkS 1 514752 PADDLE SHAFT 1 2 492584 NUT, LOCK 1/2" 6 3 EM202896 PADDLE ARM, CENTER ENGINE END 1 4 492399 B0LT, 1/2 X 3 2 5 EM200292 INSERT, PADDLE ARM 4 6 EM202...
Page 49 - PILLOW BLOCK BEARING
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 49 enGine assy. no. parT no. parT naMe QTY. reMarkS 1 EM969013 NUT 3/8" NC G5 8 2 506488 FLAT WASHER 3/8 8 3 EM905016 PILLOW BLOCK BEARING 2 4 492378 BOLT 3/8" NC X 1-3/4" G5 4 5 490957 RING, RETENTION 1 6 5...
Page 51 - NUT NYLOCK
WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) — page 51 Cabinet assy. no. parT no. parT naMe QTY. reMarkS 1 520620 CABINET, ENGINE W/DECALS ........................1................INCLUDES ITEMS W/@ 2 EM505186 BUMPER, STICK ON 4 5 503723 POP RIVET ..........................
Page 52 - terMs and COnditiOns Of sale — parts
page 52 — WM70SH5C/WM70SH8C Mixer • operaTion and parTS Manual — rev. #0 (06/07/11) terMs and COnditiOns Of sale — parts paYMenT TerMS Terms of payment for parts are net 30 days. FreigHT poliCY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments a...
Page 54 - OperatiOn and parts Manual; Your Local Dealer is:; HERE’S HOW TO GET HELP; PLEASE HAVE THE MODEL AND SERIAL; United StateS; Canada
OperatiOn and parts Manual Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING United StateS Multiquip Corporate Office MQ Parts Department 18910 Wilmington Ave. Carson, CA 90746 Contact: [email protected] Tel. (800) 421-1244 Fax (800) 537-3927 80...
Multiquip DCA-45SSIU3
Manual
Multiquip MC3PBA (B&S)
Manual
Multiquip DCA-25SSI
Manual
Multiquip HHXG5
Manual
Multiquip DA7000SSA
Manual
Multiquip PS706026
Manual
Multiquip MVC-64H
Manual
Multiquip DCA-25USIXF
Manual
Multiquip WM120SM
Manual
Multiquip DCA-20SPX
Manual
Multiquip MVC-40G
Manual
Multiquip LT6D
Manual
Multiquip GB3LED
Manual
Multiquip TLG-12SPX4
Manual
Multiquip DFG Series
Manual
Multiquip Qp-301ty
Manual
Multiquip DCA-125USJ
Manual
Multiquip WBH16
Manual
Multiquip DA7000SS
Manual
Multiquip qp402h
Manual