Multiquip SP303526 - Manuals

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 7 MQ SP-3035 CONCRETE SAW SAFETY FOR YOUR SAFETY AND THE SAFETY OF OTHERS!  NOTE This Owner's Manual has been developed to provide instructions for the safe and efficient operation of the Multiquip SP-3035 CONCRETE SA...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 8 MQ SP-3035 CONCRETE SAW HAZARD SYMBOLS  Explosive Fuel Gasoline is extremely flammable, and its vapors can cause an explosion if ignited. DO NOT start the engine near spilled fuel or combustible fluids. DO NOT fill t...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 11 MQ SP-3035 CONCRETE SAW General Safety Warnings Most accidents involving product operation, maintenance and repair are caused by failure to observe basic safety rules and precautions. Accidents can often be avoided b...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 13 MQ SP-3035 CONCRETE SAW BLADE SAFETY WARNING  ALWAYS inspect diamond blades before each use. The blade should exhibit no cracks, dings, or flaws in the steel centered core and/or rim. Center (arbor) hole must be und...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 14 MQ SP-3035 CONCRETE SAW SAW TRANSPORTATION SAFETY WARNING  Use appropriate lifting equipment to ensure the safe movement of the saw.  DO NOT use the handle bars and/or front pointer as lifting points.  NEVER attem...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 15 MQ SP-3035 CONCRETE SAW MACHINE OPERATION AND SAFETY DECALS The Multiquip SP-3035 Saw is equipped with a number of operation and safety decals. Should any of these decals become unreadable, replacements can be obtain...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 17 MQ SP-3035 CONCRETE SAW O PERATION Before Starting Walk around the saw and ensure that all guards and panels are properly installed. Wear eye and hearing protection. Wear protective clothing. 1. Check engine and hydr...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 18 MQ SP-3035 CONCRETE SAW Control Panel Fig. 5 — The Control Panel Auxiliary Switch Voltmeter Throttle Engine On-Off-Start Plunge Button Operating Instructions Speed Control Joystick Safety Warnings Water Pump Switch M...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 19 MQ SP-3035 CONCRETE SAW Engine Power, Cutting Power & Sheave Size Blade Size & Configuration per Model The SP-3035 is available in four Blade Speed configurations. The following chart shows the various config...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 20 MQ SP-3035 CONCRETE SAW Installing the Blade, Blade Guard & Blade Flange Remain Clear of all parts of saw while installing blade to prevent crush injury or death. Verify the engine start switch is OFF before inst...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 21 MQ SP-3035 CONCRETE SAW Removing the Blade, Blade Guard & Blade Flange Remain Clear of all parts of saw while installing blade to prevent crush injury or death. Verify the engine start switch is OFF before instal...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 22 MQ SP-3035 CONCRETE SAW Stacking Blades for Wide Cuts Remain Clear of all parts of saw while installing blade to prevent crush injury or death. Verify the engine start switch is OFF before installing blade. WARNING T...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 23 MQ SP-3035 CONCRETE SAW Installing and Removing the Blade Guard Blade Guards for the SP-3035 concrete saw can be installed on either side of the saw. Verify the engine start switch is OFF before installing blade. WAR...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 25 MQ SP-3035 CONCRETE SAW Installing the Flange Guard The Flange Guard provides protection from the Blade Flange not in use. 1. Verify that the unused Blade Flange is secured to the Spindle by tightening the mounting b...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 26 MQ SP-3035 CONCRETE SAW Water Supply and Control WARNING To prevent damage to the impeller of a belt driven water pump , do not run the engine with the water pump switch on, unless the water supply is connected and w...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 27 MQ SP-3035 CONCRETE SAW Handlebars The handlebars are adjustable to three different angles, for optimum operator control, and can also be slid fully inward for storage. Once handlebars are adjusted, lock them into po...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 28 MQ SP-3035 CONCRETE SAW Fueling the Saw The 3000 Series saws feature a five-gallon clear molded plastic fuel tank with a sight gauge, central drain, and shutoff valve. The gas tank cap is located at the front of the ...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 29 MQ SP-3035 CONCRETE SAW Starting and Stopping the Engine WARNING Do not leave the saw unattended while the engine is running. Do not start, park, or leave the saw unattended on a slope. CAUTION  If the saw has an op...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 30 MQ SP-3035 CONCRETE SAW Pointer Adjustment 1. Lower the front pointer assembly: Release the rope from the cam cleat, and rotate the pointer forward into position. 2. Adjust the pointer rod by loosening the lock knob:...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 31 MQ SP-3035 CONCRETE SAW Raise – Lower Controls This saw uses a 12-volt hydraulic pump and cylinder to raise and lower the blade. Controls are located on the speed control joystick handle. Fig. 17 — Joystick Handle 1....

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 32 MQ SP-3035 CONCRETE SAW Setting the Depth Gauge & Depth Stop The 3000 Series saws use a cable-controlled Depth Gauge and mechanical Depth Stop to lock the blade at the desired cut depth. See Fig. 18. Setting the ...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 33 MQ SP-3035 CONCRETE SAW Drive System The 3000 Series saws have a cable-controlled Hydro-Gear hydrostatic powered transaxle with fully adjustable F-N-R (Forward-Neutral-Reverse) speed adjustment via a joystick control...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 34 MQ SP-3035 CONCRETE SAW Drive System Controls The control handle controls FORWARD-NEUTRAL-REVERSE (F-N-R) speeds and the raising and lowering of the saw. To increase forward speed, slowly move the joystick FORWARD. P...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 35 MQ SP-3035 CONCRETE SAW Positraction Positraction, when ON, locks both drive wheels together for straight-line movement. It is recommended for all cutting and is especially helpful on uneven surfaces, and when loadin...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 36 MQ SP-3035 CONCRETE SAW Transaxle The hydrostatic-powered transaxle has no chains, sprockets or gearboxes to service. There is a simple cable control for forward-reverse motion, and a single drive belt from the engin...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 37 MQ SP-3035 CONCRETE SAW Transportation Tie-downs and Lift Point Tie-downs The saw is provided with holes at each corner of the lower frame for easy tie-down during transportation. The saw MUST be tied down whenever i...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 38 MQ SP-3035 CONCRETE SAW Operation on a Slope or Incline Never operate, cut, or face the saw down a slope or incline. The weight of the saw will shift to the front wheels allowing the rear wheels to skid or come compl...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 39 MQ SP-3035 CONCRETE SAW If an attempt is made to start the saw with the blade pinched, the starter will suffer damage. If an attempt is made to use the lift pump to raise the saw to free the blade, the lift motor and...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 40 MQ SP-3035 CONCRETE SAW M AINTENANCE This saw has many service-saving features, such as fully enclosed oil bath lubricated Spindle bearings, which require no daily lubrication.  NOTE Level the saw frame surface pri...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 41 MQ SP-3035 CONCRETE SAW Belts and Pulleys Belt Qty Part Number Spindle Drive Belt (POWERBAND) 1 520006 Transaxle Drive Belt 1 521005 Engine to Jack shaft Drive Belt 1 521005 Fig. 27 — Belt Locations V-Belt Tension Th...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 42 MQ SP-3035 CONCRETE SAW Spindle (Blade Shaft) Drive Belt Tension Adjustment  NOTE When loosening drive belts, lower the saw to reduce stress on the tensioning system, and use gravity to pull the engine forward slig...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 43 MQ SP-3035 CONCRETE SAW 4. Loosen the Outer Jam Nut on the Single Point Belt Tension Bolt. Turn the Inner Jam Nut counter-clockwise. 5. Adjust drive belt to desired tension. Do Not over tighten. 6. Tighten Engine Mou...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 44 MQ SP-3035 CONCRETE SAW Replacing the Jack Shaft Belt WARNING NEVER attempt to check or adjust the V-belt tension with the engine running. Severe injury can occur. Keep fingers, hands, hair, and clothing away from al...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 45 MQ SP-3035 CONCRETE SAW Blade Flange Removal/Installation Correct removal or installation of the Inner Blade Flange or Flange requires a Flange Puller (option Part Number 18503) as shown below. WARNING Follow instruc...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 46 MQ SP-3035 CONCRETE SAW DANGER Ensure the Outer Flange is in place to prevent the Puller and Inner Flange from flying off when the taper breaks loose, and causing injury !  NOTE If the Inner Flange does not readily...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 47 MQ SP-3035 CONCRETE SAW 6. Loosen the Mounting Bolt and remove the Outer Flange and Bushing. 7. Inspect the Inner Flange to ensure the proper seating of the tapered fit. The Inner Flange should be seated between .030...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 48 MQ SP-3035 CONCRETE SAW Spindle Replacement  NOTE To assure correct Spindle/Wheel alignment it is recommended that this operation be performed by a Multiquip Authorized Service Center. DO NOT unbolt the Spindle Mou...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 49 MQ SP-3035 CONCRETE SAW Fig. 35 — Spindle Replacement 7. Remove the Spindle.  DO NOT unbolt the Spindle Mounting Blocks, as they have been factory-installed for correct Spindle/wheel alignment. 8. Fill the new Spind...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 50 MQ SP-3035 CONCRETE SAW Circuit Breakers Three thermal circuit breakers are located behind the Control Panel access cover. Fig. 37 — Circuit Breaker location Under normal circumstance circuit breakers do not require ...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 51 MQ SP-3035 CONCRETE SAW Lubrication This saw has six grease fittings. Locations are shown in Figure 38 on the front axle assembly, and one, (not shown) on the Jackshaft assembly.  Front axle pivot bearings (2)  Hyd...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 52 MQ SP-3035 CONCRETE SAW Engine Maintenance The Model SP-3035 uses a 35 HP Wisconsin engine. See the engine manual for service details.  Check air filters daily. Do not clean. Replace as needed. See Caution below.  ...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 54 MQ SP-3035 CONCRETE SAW Control Handle Adjustment The Control Handle is adjustable to provide the preferred “feel”. 1. Using a ¼” Allen wrench and 9/16” wrench, loosen both pivot bolts until they can be turned by han...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 55 MQ SP-3035 CONCRETE SAW Hydraulic System The hydraulic system consists of: Spindle Assembly (1) Hydraulic Pump (2) Transaxle Assembly (9) Hydraulic Manifold (4) Lift Cylinder (5) Oil Filters (3, 6) Hydraulic Drive an...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 56 MQ SP-3035 CONCRETE SAW Draining & Filling the Hydraulic System To drain the Transaxle 1. Remove the drain plug from the bottom of the Spindle housing and the bottom of the Transaxle. Fig. 43 — Transaxle Drain Pl...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 57 MQ SP-3035 CONCRETE SAW Fig. 44 — Spindle Assembly 1. Raise the saw 2/3 or more up. 2. Remove the drain plug from the bottom of the Spindle housing. 3. Re-install the drain plug and install a new oil filter. CAUTION ...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 58 MQ SP-3035 CONCRETE SAW Drive Wheel Alignment Below is the suggested technique for aligning the wheels. Distance X is the same on either side; the Front Axle and Spindle must be at right angles to the frame edge. Dis...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 60 MQ SP-3035 CONCRETE SAW Positraction Adjustment Fig. 47 — Positraction Adjustment Bolt Locations 1. Lift Saw 4” to 6” and tilt forward to place spindle flanges on ground. When flanges are on the ground, depress Raise...

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 61 MQ SP-3035 CONCRETE SAW EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of ...

MQ SP-3035 Concrete Saw — Nameplate and Decals MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 63 C OMPONENT D RAWINGS Nameplate and Decals Assy. The Multiquip SP-3035 Saw is equipped with a number of operation and safety decals. Should any of these decals become unr...

MQ SP-3035 Concrete Saw — Nameplate and Decals MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 64 Nameplate and Decals Assy . NO PART NO PART NAME QTY. REMARKS 1 25250-001 DECAL, WARNING, KEEP FEET CLEAR 2 2 606004 DECAL, BLADE GUARD REMOVAL 2 3 25782 DECAL, MQ DIAMO...

MQ SP-3035 Concrete Saw — Deck/Gauge Panel Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 66 Deck/Gauge Panel Assy. NO PART NO PART NAME QTY. REMARKS 1 M600020 GAUGE PANEL 1 2 M600019 DECK PANEL 1

MQ SP-3035 Concrete Saw — Console/Sheet Metal Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 68 Console/Sheet Metal Assy . NO PART NO PART NAME QTY. REMARK 1# 0166 SCREW, HHC 3/8-16 X 7/8 3 2# 933242 WASHER, FLAT SAE 3/8 GRD 9 YZ 3 3# 204007 BELT GUARD 1 8 257...

MQ SP-3035 Concrete Saw — Access Panel Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 69 Access Panel Assy.

MQ SP-3035 Concrete Saw — Access Panel Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 70 Access Panel Assy . NO PART NO PART NAME QTY. REMARK 1# 25795 PANEL, REAR CONSOLE, RED 1 2# 29057 DOCUMENT BOX, CP90007-07 1 3# 560020 LATCH, REAR SAW ACCESS PANEL 2 4# 57...

MQ SP-3035 Concrete Saw — Fuel Tank Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 71 Fuel Tank Assy.

MQ SP-3035 Concrete Saw — Fuel Tank Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 72 Fuel Tank Assy . NO PART NO PART NAME QTY. REMARK 1# 1400003 TANK, FUEL 1 2# 29509 CAP, FUEL TANK 2.25" DIA. ONE WAY VALVE 1 3# 19633 BUSHING, RUBBER FUEL DAPCO 10672 1 4...

MQ SP-3035 Concrete Saw — Joystick Mounting Assy. MQ SP-3035 CONCRETE SAW — MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 75 Joystick Mounting Assy. 25 11 5 13 4 16 14 17 12 19 9 22 24 26 24 21 20 23 6 2 20 18 8 15 1 10 3 1 20 7

MQ SP-3035 Concrete Saw — Joystick Mounting Assy. MQ SP-3035 CONCRETE SAW — MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 76 Joystick Mounting Assy . NO PART NO PART NAME QTY. REMARK 1# 0161D NUT, HEX FINISH 5/16-18 2 2# 10019 NUT, FYLOC #10-32 1 3# 1579 SCREW. JJC...

MQ SP-3035 Concrete Saw — Lift Pump Circuit Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 77 Lift Pump Circuit Assy.

MQ SP-3035 Concrete Saw — Lift Pump Circuit Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 78 Lift Pump Circuit Assy . NO PART NO PART NAME QTY. REMARK 2 340011 PUMP, LIFT 1 3 169003 PIN, CYLINDER 2 4 447007 CYLINDER, LIFT 1 5 21159 FITTING, 45 4MJ-4MO 1 6 368...

MQ SP-3035 Concrete Saw — Water System Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 79 Water System Assy.

MQ SP-3035 Concrete Saw — Water System Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 80 Water System Assy . NO PART NO PART NAME QTY. REMARK 1 446004 VALVE, BALL, 1/2 BRASS 1 2 35047 HOSE ASM, 95.1" #8LP 1 3 35052 HOSE, 1/2 ID PUSHLOCK 250 PSI, 8" 1 4...

MQ SP-3035 Concrete Saw — Depth Indicator Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 81 Depth Indicator Assy.

MQ SP-3035 Concrete Saw — Depth Indicator Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 82 Depth Indicator Assy . NO PART NO PART NAME QTY. REMARK 1 125032 DEPTH INDICATOR U-BRACKET 1 2 110031 POINTER, DEPTH 1 3 560025 KNOB, COMFORT GRIP 1 4 460019 FLANGE BEA...

MQ SP-3035 Concrete Saw — Handle and Light Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 83 Handle and Light Assy.

MQ SP-3035 Concrete Saw — Handle and Light Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 84 Handle and Light Assy . NO. PART NO. PART NAME QTY. REMARKS 1 12387 NUT, NYLOCK 8X32 2 2 120206 LIGHT BAR, CONCRETE SAW 1 3 405001 CONNECTOR, PLUG, 4 PIN FEMALE 1 4 01...

MQ SP-3035 Concrete Saw — Front/Rear Pointer Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 86 Front/Rear Pointer Assy . NO PART NO PART NAME QTY. REMARK 1# 120045 RIGHT SIDE POINTER 1 2# 120046 LEFT SIDE POINTER 1 3# 25832 ROPE ASSY., FRONT POINTER 1 4# 11004...

MQ SP-3035 Concrete Saw — Gauges and Controls Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 87 Gauges and Controls Assy.

MQ SP-3035 Concrete Saw — Gauges and Controls Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 88 Gauges and Controls Assy . NO PART NO PART NAME QTY. REMARK 1 15171 CABLE PULL 1 2 446004 VALVE, WATER FLOW CONTROL 1 3 25627 F-N-R CONTROL ASSY. 1 4 560025 KNOB, C...

MQ SP-3035 Concrete Saw — Front Axle Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 89 Front Axle Assy.

MQ SP-3035 Concrete Saw — Front Axle Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 90 Front Axle Assy . NO PART NO PART NAME QTY. REMARK 8 913161 SCREW, HHC 7/16-14 X 2 4 9 933243 WASHER, FLAT SAE 7/16 8 10 100005 BEARING BACKING PLATE 2 11 460006 BEARING, FL...

MQ SP-3035 Concrete Saw — Depth Stop Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 91 Depth Stop Assy.

MQ SP-3035 Concrete Saw — Depth Stop Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 92 Depth Stop Assy . NO PART NO PART NAME QTY. REMARK 1 35120 DEPTH STOP LEAD SCREW 1 2 933244 WASHER, FLAT SAE 1/2 3 3 565002 SPRING, COMPRESSION, 7/8 1 4 582009 COLLAR, SET ....

MQ SP-3035 Concrete Saw — Platform Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 94 Platform Assy . NO PART NO PART NAME QTY. REMARK 1 25807 PLATFORM 1 3 924287 SCREW, FHSC, 3/8-16 X 1-1/4,NP 6 4 120038 CLIP, MOUNT,BLADEGUARD 1 5 120040 SPACER, BLADEGUARD CLI...

MQ SP-3035 Concrete Saw — Drive Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 96 Drive Assy . NO PART NO PART NAME QTY. REMARK 1 263002 TRANSAXLE ASSY. ................................................................ 1 ............. INCLUDES ITEMS W/% 2 35325...

MQ SP-3035 Concrete Saw — Bladeshaft and Mounting Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 97 Bladeshaft and Mounting Assy.

MQ SP-3035 Concrete Saw — Bladeshaft and Mounting Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 98 Bladeshaft and Mounting Assy . NO. PART NO. PART NAME QTY. REMARKS 1 35270 BLADESHAFT AND MOUNTING GROUP ................................ 1....... INCLUDES ITEM...

MQ SP-3035 Concrete Saw — Positraction Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 99 Positraction Assy.

MQ SP-3035 Concrete Saw — Positraction Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 100 Positraction Assy . NO PART NO PART NAME QTY. REMARK 1 442019 POSITRACTION ACTUATOR LEVER 1 2 560026 COVER, HANDLE FLAT RED 1 3 442020 LEVER CONNECTOR 1 4 933015 FRICTION...

MQ SP-3035 Concrete Saw — Pulley and V-Belt Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 102 Pulley and V-Belt Assy . NO PART NO PART NAME QTY. REMARKS 1 540006 PULLEY, BLADESHAFT 3.8 6G 3VX1615 .............1..........16" BLADE 1 540066 PULLEY, BLADESHA...

MQ SP-3035 Concrete Saw — Battery Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 104 Battery Assy . NO PART NO PART NAME QTY. REMARK 1 404000 BATTERY, GROUP 26R 1 2 25838 MOUNT, BATTERY CLAMP 1 3 19303 CABLE, BATTERY POS 4 GA X 48" POST 1 4 TBD CABLE, BATT...

MQ SP-3035 Concrete Saw — Engine Brackets Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 105 Engine Brackets Assy.

MQ SP-3035 Concrete Saw — Engine Brackets Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 106 Engine Brackets Assy . NO PART NO PART NAME QTY. REMARK 1 125034 LIFTING RING 1 2 933242 WASHER, FLAT SAE 3/8 GRD 9 YZ 4 3 915105 SCREW, HHC 3/8-16 X 1.0 GRD8 4 4 1250...

MQ SP-3035 Concrete Saw — Engine Installation Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 107 Engine Installation Assy.

MQ SP-3035 Concrete Saw — Engine Installation Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 108 Engine Installation Assy . NO PART NO PART NAME QTY. REMARK 1 15500 ENGINE, WISCONSIN W41770-467438R 1 2 25813 MOUNT, JACKSHAFT PIVOT ARM 1 3 120079 MOUNT, MOTOR T...

MQ SP-3035 Concrete Saw — Bladeguard Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 109 Bladeguard Assy.

MQ SP-3035 Concrete Saw — Bladeguard Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 110 Bladeguard Assy . NO PART NO PART NAME QTY. REMARK 1 M18100 BLADE GUARD 16-INCH 1 1 M18140 BLADE GUARD 20-INCH 1 1 M18180 BLADE GUARD 26-INCH 1 1 M18220 BLADE GUARD 30-INCH...

MQ SP-3035 Concrete Saw — Optional Water Pump Kit Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 111 Optional Water Pump Kit Assy.

MQ SP-3035 Concrete Saw — Optional Water Pump Kit Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 112 Optional Water Pump Kit Assy . NO PART NO PART NAME QTY. REMARK 1 M18100 BLADE GUARD 16-INCH 1 1 120084 DESCRIPTION 1 2 120085 MOUNT, WATER PUMP 1 3 342000 PUM...

MQ SP-3035 Concrete Saw — Collar Puller Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 113 Collar Puller Assy.

MQ SP-3035 Concrete Saw — Collar Puller Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 114 Collar Puller Assy . NO PART NO PART NAME QTY. REMARK 1# 584037 OUTER PULLER 1 2# 584038 PLATE, PULLER 1 3# 2549 SCREW, HHC 1/2-13 X 3 3 4# 25138 SCREW, HHC 5/8-11 X 5 T...

MQ SP-3035 Concrete Saw — Seal Sleeve Puller Seal/Seal Installation Tool MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 115 Seal Sleeve Puller/Seal Installation Tool

MQ SP-3035 Concrete Saw — Seal Sleeve Puller Seal/Seal Installation Tool MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 116 Seal Sleeve Puller/Seal Installation Tool NO PART NO PART NAME QTY. REMARK 1# 35163 SCREW, HHC 3/8 – 16 X 4 FULL THREAD 1 2 M18505 SEAL SLEEVE...

MQ SP-3035 Concrete Saw — Bushing Extension Kits MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 117 Bushing Extension Kits

MQ SP-3035 Concrete Saw — Electric Schematic MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 119 E LECTRIC S CHEMATIC

MQ SP-3035 Concrete Saw — Specifications MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 120 S PECIFICATIONS Engine Wisconsin 35 hp V-4, electronic ignition, remote oil filter and above-frame remote oil drain Precleaner Centrifugal type, self-cleaning Air Cleaner Fou...

OPERATION AND PARTS MANUAL UNITED STATES Multiquip Corporate Office MQ Parts Department 18910 Wilmington Ave. Tel. (800) 421-1244 800-427-1244 Fax: 800-672-7877 Carson, CA 90746 Fax (800) 537-3927 310-537-3700 Fax: 310-637-3284 Contact: [email protected] Mayco Parts Warranty Department 800-306-2926 F...