Multiquip pro12 - Manuals

pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) — page 5 SAfETY INfORMATION Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safety messages and...

page 6 — pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) SAfETY INfORMATION general saFety caution  never operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required...

pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) — page 7 SAfETY INfORMATION mixer saFety danger  never operate the equipment in an explosive atmosphere or near combustible materials. An explosion or fi re could result causing severe bodily harm or even death.  do not mix fl ammable o...

page 8 — pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) SAfETY INfORMATION Fuel saFety danger  do not add fuel to equipment if it is placed inside truck bed with plastic liner. Possibility exists of explosion or fi re due to static electricity.  do not start the engine near spilled ...

pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) — page 9 SPECIfICATIONS table 1. Mixer Specifications Capacity 12.0 cu. ft (340 liters) Bag Capacity 3 to 4 bags Operating Weight 1580 lbs. (716.68 kg.) Maximum Aggregate Size 1 in. (25.4 mm) Adjustable Drum Discharge Height Up to 42.5 in...

page 10 — pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) DIMENSIONS table 3. Mixer Dimensions Reference Designator dimension in. (mm.) A (Length) 73.5 (1917.7) B (Width) 35.0 (889) C (Height) 45.0 (1143) Figure 1. Mixer Dimensions A B C

pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) — page 11 GENERAL INfORMATION application The Multiquip PRO12 hydraulic mixer (with drum capacity of 12.0 cu. ft./340 liters) is shipped completely assembled, factory-tested, and ready for use.This mixer is only intended for the mixing of...

page 12 — pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) MIXER COMPONENTS Figure 2. Mixer Components 1 2 12 3 4 8 5 6 9 13 10 11 14

page 14 — pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) HYDRAULIC COMPONENTS 1 8 7 2 3 5 4 2 6 Figure 3. Hydraulic Components

page 16 — pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) BASIC ENGINE Figure 4. Engine Components initial servicing The engine (Figure 4) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the engine manufacturer’s manual for instructions and deta...

pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) — page 17 PADDLE BLADE ADjUSTMENT CAST PADDLE ENGINE END CAST PADDLE CENTER ENGINE END CAST PADDLE SIDE PADDLE BLADE END P ADDLE BLADE ROTATION RO T A TION PADDLE BLADE IS TOO TIGHT AGAINST DRUM SIDE WALLS. PADDLE BLADE IS TOO TIGHT AGAIN...

page 18 — pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) INSPECTION BeFore starting 1. Read safety instructions at the beginning of manual. 2. Clean the mixer, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner. 3. Check the air filter for di...

pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) — page 19 INSPECTION HyDRAuLiC HOSES Check hydraulic hoses (Figure 3) to make sure they are not worn, frayed or defective. grease Fittings (Bearings) Check the zerk grease fittings (Figure 9) at each end of the mixing drum. These grease f...

page 20 — pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) This section is intended to assist the operator with the initial start-up of the mixer. It is extremely important that this section be read carefully before attempting to use the mixer in the field. starting the engine (honda en...

pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) — page 21 7. Turn the engine ignition key (Figure 17) to the start position and hold it until the engine starts. When engine starts, release the key, allowing it to return to the on position. Figure 17. Engine Ignition Key 8. If the choke...

page 22 — pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) OPERATION mixing 1. On the hydraulic valve, push lever inward (Figure 23) for clockwise mixing rotation of blades. Figure 23. Hydraulic Paddle Lever 2. The paddle shaft inside the drum should be rotating at this time. 3. Add a s...

pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) — page 23 MAINTENANCE Perform engine maintenance procedures as scheduled in Table 5. 1. Service more frequently when used in dusty areas. 2. These items should be serviced by your service dealer, unless you have the proper tools and are m...

page 24 — pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) Perform the engine maintenance indicated below: Daily 1. Thoroughly remove dirt and oil from the engine and control area. Clean or replace the air cleaner elements as necessary. Check and retighten all fasteners as necessary. we...

pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) — page 25 MAINTENANCE hydraulic oil Filter Replace hydraulic oil filter (Figure 29) every 500 hours. Hydraulic tank capacity is 12 gallons (45 liters). Refill with any of the following hydraulic oil types. Shell Tellius 68, Mobil DFE26 or...

page 26 — pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) TROUBLESHOOTING Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, please take remedial action following the diagnosis based on the troubleshooting tables...

pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) — page 29 NOTES

page 30 — pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) HYDRAULIC SYSTEM LOCATOR 1 12 2 3 4 5 13 6 7 9 8 10 11

pro12 hydraulic mixer • operation manual — rev. #0 (05/06/13) — page 31 CYLINDER CYLINDER RELIEF VALVE 1750 PSI GEAR PUMP ENGINE TANK SUCTION STRAINER HYDRAULIC DUMP FORWARD/REVERSE TANK RETURN FILTER BYPASS 25 PSI HYD MOTOR 1 2 RELIEF VALVE 1750 PSI HYDRAULIC SYSTEM DIAGRAM 9 8 10 12 2 5 1 4 11 6 7...

OperatiOn Manual Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING United StateS Multiquip Corporate Office MQ Parts Department 18910 Wilmington Ave. Carson, CA 90746 Contact: [email protected] Tel. (800) 421-1244 Fax (310) 537-3927 800-427-1244...