Multiquip HTN-27K-TCSL - Manuals

Multiquip HTN-27K-TCSL – Manual in PDF format online.

Manuals:

Manual

Manual Multiquip HTN-27K-TCSL

Summary

Page 3 - SILICOSIS WARNING

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 3 Grinding/cutting/drilling of masonry, concrete, metal andother materials with silica in their composition may giveoff dust or mists containing crystalline silica. Silica is abasic component of sand, quartz, brick cla...

Page 4 - TABLE OF CONTENTS; MQ WHITEMAN — HTN-SERIES; NOTE

PAGE 4 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 4 TABLE OF CONTENTS MQ WHITEMAN — HTN-SERIES RIDE-ON POWER TROWEL Proposition 65 Warning ............................................. 2Silicosis/Respiratory Warnings .................................. ...

Page 5 - PARTS ORDERING PROCEDURES; Ordering parts has never been easier!; Choose from three easy options:; Order via Internet; Order

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 5 PARTS ORDERING PROCEDURES www .m ultiquip .com Ordering parts has never been easier! Choose from three easy options: WE ACCEPT ALL MAJOR CREDIT CARDS! When ordering parts, please supply: ❒ ❒ ❒ ❒ ❒ Dealer Account Numb...

Page 6 - TRAINING CHECKLIST

PAGE 6 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 6 TRAINING CHECKLIST This checklist lists some of the minimum requirements for machine operation. Please feel free to make copies for daily use. Use thischecklist when training a new operator or use as ...

Page 7 - DAILY PRE-OPERATION CHECKLIST; li

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 7 DAILY PRE-OPERATION CHECKLIST COMMENTS: DAILY PRE-OPERATION CHECKLIST T S I L K C E H C N O I T A R E P O - E R P Y L I A D 1 .l e v e L li O e n i g n E 2 d i u l F x o b r a e G l e v e L . 3 .l e v e L t n a l o o...

Page 8 - HTN-SERIES — SAFETY MESSAGE ALERT SYMBOLS

PAGE 8 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 8 HTN-SERIES — SAFETY MESSAGE ALERT SYMBOLS HAZARD SYMBOLS Engine exhaust gases contain poisonouscarbon monoxide. This gas is colorless andodorless, and can cause death if inhaled. NEVER operate this eq...

Page 9 - A LWAY S; Sight and Hearing hazard; Over Speed Conditions; NEVER; CAUTION

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 9 Accidental Starting Respiratory Hazard A LWAY S we a r a p p r o ve d r e s p i r a t o r y protection. ALWAYS wear approved eye and hearing protection. Sight and Hearing hazard Equipment Damage Messages Other import...

Page 10 - HTN-SERIES — RULES FOR SAFE OPERATION; WARNING

PAGE 10 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 10 HTN-SERIES — RULES FOR SAFE OPERATION SAFETY ■ DO NOT operate or service this equipment before you read, understand, and complywith all safety messages in this manual.The manual must be kept availab...

Page 11 - ALWAYS

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 11 HTN-SERIES — RULES FOR SAFE OPERATION ■ NEVER run engine without air filter. Severe engine damage may occur. Service air filter frequently to prevent carburetormalfunction. ■ NEVER place your feet or hands inside th...

Page 14 - HTN-SERIES — OPERATION AND SAFETY DECALS; Machine Safety Decals; DANGER

PAGE 14 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 14 HTN-SERIES — OPERATION AND SAFETY DECALS Machine Safety Decals The HTN-SERIES Ride-On Power Trowel is equipped with a number of operation and safety decals. These decals are provided foroperator saf...

Page 15 - normal; ” circumstances. Sound pressure

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 15 HTN-SERIES— SPECIFICATIONS (TROWEL) Figure 1. HTN-SERIES Dimensions 2. Sound pressure is a weighted measure. It is measured atthe operator's ear position while the walk-behind trowel isoperating at full throttle on ...

Page 17 - HTN-SERIES — GENERAL INFORMATION; HTN SERIES Ride-On Power Trowel Familiarization

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 17 HTN-SERIES — GENERAL INFORMATION HTN SERIES Ride-On Power Trowel Familiarization The HTN SERIES Ride-On Power Trowel is designed for thefloating and finishing of concrete slabs. Take a walk around your trowel. Take ...

Page 18 - HTN-SERIES — CONTROLS AND INDICATORS

PAGE 18 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 18 HTN-SERIES — CONTROLS AND INDICATORS Figure 2. HTN-SERIES Controls and Indicators (Front) 9. Fuel Gauge/Filler Cap – Indicates the amount of fuel in the fuel tank. Remove this cap to add fuel. 10. F...

Page 20 - HTN-SERIES — BASIC ENGINE

PAGE 20 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 20 HTN-SERIES — BASIC ENGINE Figure 4. Engine Controls and Components INITIAL SERVICING The engine must be checked for proper lubrication and the fuel tankfilled with fuel prior to operation. Refer to ...

Page 21 - HTN-SERIES — NEW MACHINE SETUP INSTRUCTIONS

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 21 HTN-SERIES — NEW MACHINE SETUP INSTRUCTIONS Trowel Pre-Set Up Instructions The purpose of this section is to assist the user in setting up a NEW trowel. If your trowel is already assembled, (seat, handles, knobs and...

Page 22 - Figure 5. Engine Oil Dipstick; Table 3. Recommended Viscosity Grades

PAGE 22 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 22 HTN-SERIES — INITIAL START-UP The following section is intended as a basic guide to the ride-ontrowel operation, and is not to be considered a complete guideto concrete finishing. It is strongly sug...

Page 23 - HTN-SERIES — OPERATION; Figure 8. Blade Speed Control Foot Pedal

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 23 HTN-SERIES — OPERATION NEVER disable or disconnect the "safety stop switch". It is provided for the operator's safety and injury or death may result if it is disabled, disconnected or improperlymaintained. 1...

Page 24 - Figure 11. Left and Right Control Levers; FORWARD DIRECTION; look-out for objects which might cause damage

PAGE 24 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 24 HTN-SERIES — OPERATION 3. Practice holding the machine in one place as you increaseblade speed. When about 75% of maximum blade speedhas been reached, the blades will be moving at properfinishing sp...

Page 25 - HTN-SERIES — MAINTENANCE; Figure 12. Engine Service Areas

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 25 Maintenance HTN-SERIES — MAINTENANCE 1 . Oil Level Dipstick 2 . Air Cleaner Cover 3. Carburetor 4 . Governor 5 . Oil Fill Cap (On either side) 6 . #2 Valve Cover 7. #2 Exhaust Port 8. Spark Plug, #2 side 9 . Oil Fil...

Page 28 - Figure 14. Oil Filter; seal; Long Term Storage

PAGE 28 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 28 See the engine manual supplied withyour machine for appropriate enginem a i n t e n an c e s c h ed ul e a n dtroubleshooting guide for problems. NOTE Oil And Fuel Lines ■ Check the oil and fuel lin...

Page 29 - Figure 17. Drive Belt Guard Cover; Figure 16. Wooden Block For Spacer

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 29 HTN-SERIES — MAINTENANCE Checking The Drive Belt The drive belt needs to be replaced as soon as it starts to showsigns of wear. Indications of excessive belt wear are fraying,squealing when in use, belts that emit s...

Page 30 - HTN-SERIES— MAINTENANCE; CUT; Figure 19. Holding Lower Pulley Open; Installing the Drive Belt (Using Replacement Drive Belt); Figure 20. Drive Belt Install

PAGE 30 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 30 HTN-SERIES— MAINTENANCE 4. If the belt is not being reused (recommended), CUT the drive belt. Ensure all belt remnants are removed fromthe pulleys. 3. Insert the 3/4" X 1" X 3-1/4" block...

Page 31 - Figure 21. Spare Drive Belt Replacement; will

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 31 HTN-SERIES— MAINTENANCE 3. Once the CV-joint has been separated from the left-sidegearbox, push the CV-joint inward so that a gap existsbetween the gearbox and the CV-joint (Figure 21). Slidethe spare V-belt between...

Page 32 - Figure 26. Pulley Conditions; pulley; The; Fig. 22 Torque Converter/Variable Pitch Pulley

PAGE 32 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 32 NEUTRAL LOW SPEED HIGH SPEED DRIVEPULLEY DRIVENPULLEY A B C Figure 26. Pulley Conditions HTN-SERIES— MAINTENANCE The "Variable Pitch Pulleys" have one fixed face , and one moveable face . Th...

Page 33 - Figure 27. Pulley Spring and Cam Bracket

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 33 How It Works (Figure 26) Condition A: z z z z z Engine Idling z z z z z Drive Pulley: Small z z z z z Driven Pulley: Large z z z z z Belt: Loose and Stationary Condition B: z z z z z Engine Accelerating z z z z z Dr...

Page 34 - Stabilizer Ring Removal; Trowel Arm adjustment Procedure

PAGE 34 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 34 ■ Does the trowel have a perceived rolling or bouncingmotion? ■ Does the guard ring “rock up and down” relative to theground? 2. Start engine, and bring trowel blades up to full speed and look for t...

Page 38 - Figure 40. Z-Clip Finisher Pan Installation; Installing Pans Onto Finisher Blades; Decommissioning Trowel/Components; unacceptable and unrepairable safety risk due to wear

PAGE 38 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 38 HTN-SERIES — MAINTENANCE 3 2 4 1 Figure 40. Z-Clip Finisher Pan Installation These round discs sometimes referred to as "pans" attach to thespiders arms and allow early floating on wet concr...

Page 44 - TERMS AND CONDITIONS OF SALE — PARTS

PAGE 44 — HTN 31V HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 44 Effective: February 22, 2006 TERMS AND CONDITIONS OF SALE — PARTS PAYMENT TERMS Terms of payment for parts are net 30 days. FREIGHT POLICY All parts orders will be shipped collect orprepaid with the...

Page 45 - NOTE PAGE

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 45 NOTE PAGE

Page 46 - OPERATION MANUAL; Your Local Dealer is:; HERE'S HOW TO GET HELP; PLEASE HAVE THE MODEL AND SERIAL; UNITED STATES

OPERATION MANUAL Your Local Dealer is: HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING © COPYRIGHT 2007, MULTIQUIP INC. Multiquip Inc, the MQ logo and the Whiteman logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without...