Multiquip GB3LED - Manuals

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 5 SAFETY INFORMATION GENERAL SAFETY CAUTION  NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devic...

PAGE 6 —GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) SAFETY INFORMATION LIGHTING SYSTEM SAFETY WARNING  NEVER disconnect any emergency or safety devices. These devices are intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm o...

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 7 SAFETY INFORMATION BALLOON SAFETY WARNING  To prevent serious burns, NEVER touch or unzip the balloon envelope when the lamp is on. CAUTION  ALWAYS keep the balloon away from sharp objects and excessive amounts of he...

PAGE 8 —GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) SPECIFICATIONS Table 1. Specifications Globug Lighting SystemModel GB3LED Input Voltage 100 VAC Frequency 50 Hz/ 60 Hz Max. Current 3.3 Amps (100 V @300 W) Weight Lamp Fixture 18.74 lb (8.5 kg) Mast 4.85 lb (2.2 kg) Tri...

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 9 DIMENSIONS Table 2. Dimensions Reference Letter Dimension in. (mm.) Reference Letter Dimension in. (mm.) A Upper Position - 44.7 in. (1,135 mm.) Lower Position - 52.4 in. (1,330 mm.) F 33.5 in. (850 mm.) B Upper Positi...

PAGE 10 —GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) ILLUMINATION RANGE Figure 2. Illumination Range (Foot Candles) tripod 1st StageTwo stage mast tripod 2nd StageTwo stage mast 20ft 20ft 2.5 1 10 20 5 0.5 15 15 2.5 1 10 5 0.5 20

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 11 GENERAL INFORMATION The Multiquip GloBug GB3LED is a general purpose, portable, glare-free lighting systems Typical applications for these types of lighting systems include construction sites, emergency road crews and...

PAGE 12 —GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) COMPONENTS Figure 4. Major Components 10 2 4 5 6 1 7 8 9 3 COVER CARRYING CASE

PAGE 14 —GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) SETUP TRIPOD DEPLOYMENT 1. Place the tripod on a firm level surface so that it will not slide or turn over. Make sure there is enough space around the unit for the tripod legs to be deployed. 2. Remove tripod from its ...

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 15 SETUP BALLOON ASSEMBLY PLACEMENT 1. Place balloon assembly (Figure 8) onto mast and tighten Upper T-handle. Figure 8. Light Asembly Placement 2. Unsnap the three buttons on the bottom of the balloon. Expose the balloo...

PAGE 16 —GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) RAISING THE MAST Before raising the mast, make sure the upper T-handle bolt lock (Figure 12) is securely tightened. This will prevent the balloon/lamp assembly from falling off. In addition make sure that the lamp powe...

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 17 OPERATION APPLYING POWER 1. Connect the AC power cable to the 120 VAC receptacle on the generator used. See Figure 13. Figure 13. Connecting to Power Source 2. Start the generator as indicated in the generator manual....

PAGE 18 —GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) STORAGE 1. L o o s e n t h e l owe r T- h a n d l e by t u r n i n g h a n d l e counterclockwise (Figure 16). Push down on mast until mast is fully inserted into mast housing. Tighten T-handle fully. Figure 16. Loweri...

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 19 7. To retract tripod legs (Figure 20) and place in the stow position, lift up on mast while pulling up on the velcro strap. Continue pulling upward on the mast until the tripod legs are fully retracted and are in the ...

PAGE 20 —GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) MAINTENANCE REPLACING THE LAMP REPLACING BALLOON ENVELOPE 1. Unzip the zipper (Figure 38) at the top and bottom of the balloon envelope (cover). Figure 23. Unzipping the Balloon Envelope 2. Slide the old or worn balloo...

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 21 MAINTENANCE FILTER REPLACEMENT 1. Remove the balloon as described in the STORAGE section. 2. Turn the balloon/lamp assembly upsidedown to access the filter. See Figure 27. Figure 27. Accessing Filter 3. Turn the three...

PAGE 22 —GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) MAINTENANCE B2 E1 B1 T2 T4 T3 L1 L2 E2 B3 B4 Figure 30. Maintenance Check Points

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 23 MAINTENANCE For a prolonged life cycle an extended quality follow the recommended GloBug lighting system service guidelines as referenced in Figure 30 and Table 3. Table 3. Periodic Check and Maintenance Figure Part C...

PAGE 24 —GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) WIRING DIAGRAM Indicator Lamp Dimmer Switch Figure 31. Electrical Wiring Diagram

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 25 TROUBLESHOOTING Troubleshooting Symptom Possible Problem Solution Lamp does not light. Is plug connected? Plug in correctly. Is generator’s main switch turned off? Turn on switch.Are any wire cables disconnected? Conn...

PAGE 26 —GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are an...

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 27 SUGGESTED SPARE PARTS GLOBUG LIGHTING SYSTEM 1 TO 3 UNITS Qty. P/N Description 3............A300260400 ......... LED HEATSINK ASSY 2............A100015901 ........ BALLOON CLOTH

PAGE 28 —GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) NAMEPLATE AND DECALS 2 1 10 8 9 6 7 5 3 4

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 29 NAMEPLATE AND DECALS NO. PART NO. PART NAME QTY. REMARKS 1 A400204801 DECAL; ELECTRIC SHOCK, HIGH VOLTAGE, BURN HAZ. 1 2 A400340900 DECAL; LIGHT CONTROL 1 3 A400340800 DECAL; DANGER, BALLOON INFORMATION 1 4 A400287600...

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 35 MAST ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 A300200300 FIRST MAST ( φ 45*1050) ASSY 1 2 A300200600 SECOND MAST (φ 38*1200) ASSY 1 3 A400187601 KNOB 1 4 A400229900 BOTTOM PLATE ( φ 33.6) 1 5 0024705008 SET SCREW (...

PAGE 36 —GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) TERMS AND CONDITIONS OF SALE — PARTS PAYMENT TERMS Terms of payment for parts are net 30 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are...

GB3LED LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (03/18/14) — PAGE 37 NOTES

OPERATION AND PARTS MANUAL Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING © COPYRIGHT 2014, MULTIQUIP INC. Multiquip Inc , the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written pe...