Multiquip GB114BS/BP - Manuals

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 5 SAFETY INFORMATION LIGHTING SYSTEM SAFETY DANGER NEVER  use lighting system in rain, snow or areas of high humidity that could generate electrical storms. WARNING NEVER  disconnect any emergency or safety ...

PAGE 6 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) SAFETY INFORMATION GENERATOR SAFETY If using a generator to power lighting system, refer to applicable generator manual safety information section. ELECTRICAL SAFETY DANGER Lighting system is equipped with a...

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 7 SAFETY INFORMATION LOADING AND UNLOADING If lighting system is equipped with a transport lifting hook, refer to the following safety information. CAUTION Before lifting, make sure that lighting system parts ...

PAGE 8 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) SPECIFICATIONS Specifi cations Table 1. GloBug Lighting System Model GB114BS/GB114BP Input Voltage 120 VAC Ballast Magnetic Ballast 60 Hz Frequency 60 Hz Single-Phase Max. Current 9.5 Amps Lamp Lamp Type 100...

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 11 FOOTCANDLE PLOT 360° Coverage Floodlight Footcandle Plot (BAL-115 Drum Shaped) Figure 3. Scale: Grid = 50 ft. (15.25 meters) Values listed as footcandles .5 1 2 5 10

PAGE 12 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) GENERAL INFORMATION The Multiquip GloBug GB114BS, and GB114BP are general pur pose por table glare-free lighting systems. Typical applications for these types of lighting systems include construction sites,...

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 13 NOTES

PAGE 14 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) COMPONENTS Major Components Figure 5.

PAGE 16 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) SETUP POLE SETUP Refer to Figure 6 for the following procedure. R e m ove t h e o f f s e t p o l e ( B ) f r o m t h e s h i p p i n g 1. container. Attached to the offset pole is a 17/19 mm open-end 2. wr...

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 17 SETUP REMOVING THE PROTECTIVE COVERING Expose the balloon by pulling down on the velcro tab 1. and unzip the protective cover as shown in Figure 7. Folding Protective Cover Figure 7. VELCRO TAB PROTECTIVE C...

PAGE 18 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) OPERATION RAISING THE EXTENSION POLE Before raising the extension pole, make sure the 1. T-handle bolt lock (Figure 6-O) is securely tightened. This will prevent the balloon/lamp assembly from falling off. ...

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 19 OPERATION/SHUTDOWN Place the ON/OFF switch (Figure 12) on the ballast in 3. the ON position. Ballast On/Off Switch (On Position) Figure 12. Notice that the balloon envelope will begin to deploy 4. as soon a...

PAGE 20 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) LOWERING THE EXTENSION POLE Using the supplied 19 mm wrench, loosen extension 1. clamp bolt (Figure 6-Q). Carefully pull down on the adjustable extension pole 2. (Figure 6-L) and lower lamp assembly. Remove...

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 21 MAINTENANCE REMOVING THE LAMP ASSEMBLY Allow lamp (Figure 17) 15-20 minutes to cool before 1. changing. Hot Lamp Surface Figure 17. If lamp assembly is attached to offset pole, loosen 2. T-handle knob (Figu...

PAGE 22 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) Push down and hold the lamp holder (spring loaded) 3. away from the lamp (Figure 21). Unscrew the lamp (turn counterclockwise) from the lamp socket. Removing the Lamp Figure 21. INSTALLING A NEW LAMP When i...

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 23 MAINTENANCE FILTER REPLACEMENT Remove the balloon as described in the "Removing 1. the Lamp/Balloon" section. Disconnect the lamp power cable (Figure 5). 2. Rotate the balloon/lamp base assembly so ...

PAGE 24 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) MAINTENANCE Maintenance Check Points Figure 30. P5 P6 P4 P1 P3 P2 B1 B2 E1 E2 E3 B4 L2 B3 L1 L4 L3 L5

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 25 MAINTENANCE For a prolonged life cycle an extended quality follow the recommended GloBug lighting system service guidelines as referenced in Figure 30 and Table 4. Periodic Check and Maintenance Table 4. Fi...

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 27 WIRING DIAGRAM Electrical Wiring Diagram Figure 31. FAN MOTOR 1000 WATT METAL HALIDE LAMP ORANGE PURPLE BLACK NOT USED RED/BLK YEL YEL BLK/YEL CAPACITOR 24uF @480 VDC TRANSFORMER (BALLAST) BLK RED 120 VAC C...

PAGE 28 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) VOLTAGE MEASUREMENTS VOLTAGE MEASUREMENT (BALLAST NO-LOAD) Remove lamp from pipe frame as refrenced in 1. maintenance section of this manual. Place lamp in a safe place where it will not get damaged 2. or b...

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 29 Voltage Measurements Figure 32. VOLTAGE MEASUREMENTS

PAGE 30 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) EXPLANATION OF CODE IN REMARKS COLUMN The contents and part numbers listed in the parts section aresubject to change without notice . Multiquip does not guarantee the availability of the parts listed. When ...

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 31 SUGGESTED SPARE PARTS GB114BP/BS GLOBUG LIGHTING SYSTEM 1 to 3 units QTY. P/N DESCRIPTION 2............LB41827 ............... LAMP2............A300033800 ......... BALLAST2............A300038400 ......... ...

PAGE 32 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) NAMEPLATE AND DECALS DANGER To avoid accident or injuryNEVER exceed a travelspeed of 5 MPH when usinglighting system on a mobileequipment. DCL 1001 To avoid accident orinjury ALWAYS makecertain hardware iss...

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 33 NO. PART NO. PART NAME QTY. REMARKS 1 DCL1001 DECAL; DANGER, TRAVEL SPEED ............................... 1 ....... REPLACES P/N A400084000 2 DCL1002 DECAL; DANGER, PIPE CLAMP 1 3 DCL416 DECAL; DANGER, ELEC...

PAGE 38 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) FAN BLOWER/LAMP BASE ASSEMBLY

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 39 FAN BLOWER/LAMP BASE ASSEMBLY NO. PART NO. PART NAME QTY. REMARKS A A000017600 BALLOON ASSY ............................................................. 1 ....... S/N G30001 SEE NOTE 1 A A000017601 BALLOON...

PAGE 40 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) BALLOON/LAMP GUARD ASSEMBLY 1 2 3A 4 5 6 7 8 8 19 18 9 10 11 10 11 11 12 13 10 15 17 16 17 14 10 11 A 3 20 21 BALLOON PATCH KIT

PAGE 42 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) OFFSET POLE ASSEMBLY 22 20 21 9 28 11 12 13 15 14 14 12 16 14 17 19 17 5 23 16 14 17 19 15 14 24 18 26 2 21 22 12 14 18 24 4 6 2 3 10 11 12 8 27 25 1 7 29 13 29 A

PAGE 44 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) TERMS AND CONDITIONS OF SALE — PARTS PAYMENT TERMS Terms of payment for parts are net 30 days. FREIGHT POLICY All parts orders will be shipped collect orprepaid with the charges added to the invoice.All shi...

Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING © COPYRIGHT 2009, MULTIQUIP INC. Multiquip Inc, the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademar...