Multi-Tech Systems MVP110 - Manuals

5 Introduction Related Documentation The MVP110 Quick Start Guide is intended to be used byqualified systems administrators and network managers. Thisquick start provides the necessary information for a qualifiedperson to unpack, cable, load software, and configure the unitfor proper operation. A de...

MultiVOIP Quick Start Guide 6 Installing Your MultiVOIP The basic steps of installing your MultiVOIP network involveunpacking the units, connecting the cables, and configuringthe units using the included management software (MultiVOIPConfiguration). The recommended installation processincludes three...

MultiVOIP Quick Start Guide 8 Unpacking Your MultiVOIP Remove all items from the box (See Figure 4). MADE IN U.S.A MADE IN U.S.A www .multitech.com Voice/Fax over IP Networks Figure 4. Unpacking Safety Warnings Caution: Danger of explosion if battery is incorrectly replaced. A lithium battery on the...

9 Cabling Cabling Your MultiVOIP Cabling your MultiVOIP involves making the proper Power,Command Port, phone system, and Internet connections.Figure 5 shows the back panel connectors and the associatedcable connections. The following procedure details the stepsnecessary for cabling your MultiVOIP. 1...

11 Configure Host MultiVOIP Configuring Your Host MultiVOIP Configuring your Host MultiVOIP involves software loadingand configuration. The software loading procedure does not provide every screenor option in the loading process. It is assumed that a technicalperson with a thorough knowledge of Wind...

MultiVOIP Quick Start Guide 14 8. The following message displays: Click No to continue. 9. In the program group, double-click Upgrade Software. 10. The following window displays. Click Yes to continue. 11. The IP Protocol Default Setup dialog box displays. The default Frame Type is TYPE_II. If this ...

15 Configure Host MultiVOIP The IP address is your unique LAN IP address, and theGateway address is the IP address of the deviceconnecting your MultiVOIP to the Internet. Click OK when you are finished. 13. The Channel Setup dialog box displays. It is used to define the voice/fax channel interface, ...

MultiVOIP Quick Start Guide 16 again. This option is available for all interface types. Inthe Flash Timer box, enter the time, in milliseconds, forthe duration of flash hook signals output on the interface. To dedicate the local voice/fax channel to a remote voice/fax channel, (so you will not have ...

17 Configure Host MultiVOIP 17. The Billing/Security tab displays the parameters for billing options, call authentication, and automaticdisconnection. 18. You can set up billing options for inbound and outbound calls by selecting them in the Billing Options group andthen entering the charge in cents...

21 Configure Host MultiVOIP 28. Click OK and you are returned to the Phone Directory Database dialog box, which now includes phone number101 with its IP address, channel number, and description. 29. Click Add and the Add/Edit Phone Entry dialog box displays again. 30. Enter the phone number for the ...

23 Configure Host MultiVOIP 35. The Save Setup dialog box displays. Click OK to proceed. 36. After the setup is written to the MultiVOIP, the unit is rebooted. 37. Verify that the BOOT LED on the MultiVOIP is off after the download is complete. This may take several minutes asthe MultiVOIP reboots. ...

MultiVOIP Quick Start Guide 24 Configuring Your ClientMultiVOIPs If you are installing a MultiVOIP behind a firewall, you need toadd the following UDP ports to your firewall. 900 Signaling Information 5004 RTP Packets 5000 Status Information 5005 RTCP Packets Refer to your firewall user documentatio...

25 Configure Client MultiVOIPs match your IP network, select the Frame Type from theFrame Type list. The Frame Type choices are TYPE_IIand SNAP. 4. In the Port Address group, enter the IP Address and IPMask. In the Gateway Address group, enter the gatewayIP address for the client unit. The IP addres...

MultiVOIP Quick Start Guide 26 Check with your in-house telephone personnel to verifywhether your local PBX dial signaling is Pulse or DTMF(tone). Set the Regeneration option accordingly. In theMax Dial Digits box, enter the maximum number of digitsallowed when dialing a phone number. The default se...

27 Configure Client MultiVOIPs If you changed the voice coder, ensure that the samevoice coder is used on the voice/fax channel you arecalling. Otherwise, you will always get a busy signal. 9. The Fax group enables you to select the maximum baud rate for faxes and adjust the fax volume. If you do no...

MultiVOIP Quick Start Guide 30 20. Verify that the Boot LED on the MultiVOIP is off after the download is complete. This may take several minutes asthe MultiVOIP reboots. 21. You are returned to the main menu. Your MultiVOIP is operational at this time. Repeat this procedure for each of the client u...

31 Configure Client MultiVOIPs Deploying the VOIP Network Deploying the VOIP network involves the VOIP Administratordeveloping the VOIP Dialing Directory and deploying the pre-configured client MultiVOIPs to their remote sites. The remotesite administrators need only connect power to the pre-configu...

MultiVOIP Quick Start Guide 32 Remote Site Administrator 3. Unpack your MultiVOIP. 4. Connect one end of the power supply to a live AC outletand connect the other end to the Power connection onyour MultiVOIP. FXS Ethernet Connection Power Connection ETHERNET POWER Voice/Fax Channel Connection PHONE ...

33 Deploy VOIP Network Limited Warranty Multi-Tech Systems, Inc. (“MTS”) warrants that its products willbe free from defects in material or workmanship for a period oftwo years from the date of purchase, or if proof of purchase isnot provided, two years from date of shipment. MTS MAKESNO OTHER WARRA...

MultiVOIP Quick Start Guide 34 Technical Support Multi-Tech Systems has an excellent staff of technical supportpersonnel available to help you get the most out of your Multi-Tech product. If you have any questions about the operationof this unit, or experience difficulty during installation you canc...

35 Warranty and Regulatory Information FCC Declaration NOTE: This equipment has been tested and found to comply withthe limits for a Class A digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonableprotection against harmful interference when the equipment ...