MSI AM-780E V1.1- Manuals

Page 2 - Southbridge: AMD SB710

1-2 OVERVIEW ▍ M ainboard S pecificationS Processor AMD Sempron/Athlon Single-Core/Dual-Core processors (Optional) 4-pin CPU fan pinheader with Smart Fan Speed Control HyperTransport Supports Hyper Transport, up to 6400MHz Chipset Northbridge: AMD RS780E Southbridge: AMD SB710 Memory 1 DDR2 400/533/...

Page 9 - Chapter 2; Hardware Setup

This chapter provides you with the information on mainboard hardware configurations. Incorrect setting of jumpers and connectors may damage your main - board. Please pay special attention not to connect these headers in wrong direction. DO NOT adjust any jumper while the mainboard is powered on. Cha...

Page 11 - eMory; The DIMM slot is intended for memory modules.; Installing Memory Modules; Locate the SO-DIMM slot. Align the notch on the DIMM with the key on; Important

2-3 MS-9858 M eMory The DIMM slot is intended for memory modules. Installing Memory Modules Locate the SO-DIMM slot. Align the notch on the DIMM with the key on the slot and insert the DIMM into the slot at a 45-degree angle. Push the DIMM gently forwards until the slot levers click and lock the DIM...

Page 12 - You may use the 20-pin ATX power supply as you like. If you’d like to use

2-4 HARdWARE SETuP ▍ p ower S upply ATX 20-Pin Power Connector: PWRCONN1 You may use the 20-pin ATX power supply as you like. If you’d like to use the 20-pin ATX power supply, please plug your power supply along with pin 1 & pin 13. There is also a foolproof design on pin 11, 12, 23 & 24 to ...

Page 14 - The standard RJ-45 LAN jack is for; Audio Ports; between audio effects according to the color of audio jacks.

2-6 HARdWARE SETuP ▍ LAN The standard RJ-45 LAN jack is for connection to the Local Area Network (LAN). You can connect a network cable to it. LED Color LED State Condition Left Yellow Off LAN link is not established. On (Steady state) LAN link is established. On (brighter & pulsing) The compute...

Page 15 - onnectorS; Chassis Intrusion Connector: JCHASSIS1; the warning, you must enter the BIOS utility and clear the record.; loss may occur during transmission.; SA

2-7 MS-9858 c onnectorS Chassis Intrusion Connector: JCHASSIS1 This connector is provided to connect the chassis intrusion switch cable. If the chassis is opened, the chassis intrusion mechanism will be activated. The sys - tem will record this status and show a warning message on the screen. To cle...

Page 16 - HARdWARE SETuP; advantage of the CPU fan control.; SPI Flash ROM Connector: JSPI1; This connector is used to flash SPI flash ROM.

2-8 HARdWARE SETuP ▍ Fan Power Connector: CPu_FAN1, SYS_FAN1 The fan power connector supports system cooling fan with +12V. When con - necting the wire to the connectors, always note that the red wire is the positive and should be connected to the +12V; the black wire is Ground and should be connect...

Page 17 - Backlight Connector: J1

2-9 MS-9858 Backlight Connector: J1 This connector is provided for LCD backlight options.tended Capabilities Par - allel Port (ECP) mode. Serial Port Connector: JCOM1, JCOM2 This connector is a 16550A high speed communications port that sends/re - ceives 16 bytes FIFOs. You can attach a serial devic...

Page 18 - Front Panel Connector: JFP1; Audio Amplifier Connector: JAMP1

2-10 HARdWARE SETuP ▍ Front Panel Connector: JFP1 This connector is provided for electrical connection to the front panel switches /LEDs and is compliant with Intel Front Panel I/O Connectivity Design Guide. PIN SIGNAL dESCRIPTION 1 234 5 6 789 HDD + PLED HDD - SLEDRESET-PWSW +RESET +PWSW - NC Hard ...

Page 19 - Front Panel Audio Connector: JAud1; by Realtek ALC888 controller.

2-11 MS-9858 Front Panel Audio Connector: JAud1 This connector allows you to connect the front panel audio and is controlled by Realtek ALC888 controller. PIN SIGNAL dESCRIPTION 1 234 5 6 78910 MIC_LGNDMIC_RPRESENCE#LINE _RLINE NEXT RFRONT IO SENCE NC LINE_LLINE NEXT L Microphone - Left channelGroun...

Page 21 - LVdS Flat Panel Connector: JLVdS1; to proper power voltage.; Display Matrix

2-13 MS-9858 LVdS Flat Panel Connector: JLVdS1 The LVDS (Low Voltage Differential Signal) connector provides a digital interface typically used with flat panels. After connecting an LVDS interfaced flat panel to the JLVDS1, be sure to check the panel datasheet and set the JVDD1 jumper (p. 2-15) to p...

Page 22 - TPM Module Connector: JTPM1

2-14 HARdWARE SETuP ▍ TPM Module Connector: JTPM1 This connector connects to a TPM (Trusted Platform Module) module (optional). Please refer to the TPM security platform manual for more details and usages. PIN SIGNAL PIN SIGNAL 1 3 57911 13 TPM_CLKTPM_RST#LPC_LAD0LPC_LAD1LPC_LAD2LPC_LAD3LPC_FRAME# 2...

Page 23 - uMper; LVdS Power Selection Jumper: JVdd1; system configuration, set the jumper to clear data.; Keep Data

2-15 MS-9858 J uMper LVdS Power Selection Jumper: JVdd1 Use this jumper to specify the operation voltage of the LVDS interfaced flat panel. 1 1 +3.3V 1 +5V 1 +12V Clear CMOS Jumper: JCMOS1 There is a CMOS RAM onboard that has a power supply from an external bat - tery to keep the data of system conf...

Page 24 - PCI (Peripheral Component Interconnect) Express Slot; NAND Flash; PCI (Peripheral Component Interconnect) Slot; that comply with PCI specifications.; lot

2-16 HARdWARE SETuP ▍ PCI (Peripheral Component Interconnect) Express Slot The PCI Express slot supports the PCI Express interface expansion card.The CON1 is Mini PCI-E connector for wireless LAN, TV tuner, and Robson NAND Flash . PCI (Peripheral Component Interconnect) Slot The PCI slot supports LA...