Mr. Coffee APS-998 - Manuals

Page 2 - To program these selectable features

128-7405 2 of 28 2 To program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable ...

Page 5 - INSTALLATION OF THE MAJOR COMPONENTS:

128-7405 5 of 28 This Remote Start/Alarm System is designed to be used with Automatic Transmission- Fuel InjectionVehicles Only! The unit provides a selectable ignition control that allows a number of selectable timed outputs for glow plug pre-heat in addition to a "Wait To Start Input" eith...

Page 7 - WIRING THE 6 PIN MAIN POWER HARNESS:

128-7405 7 of 28 This unit is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this combinationAlarm/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT be in-stalled into a vehicle with a manually operated transmission. Doing so may result in serio...

Page 8 - YELLOW START WIRE DETAIL

128-7405 8 of 28 IMPORTANT!It is the responsibility of the installing technician to determine the load factor of the vehicles electricalcircuits when the vehicle is running, and to adequately fuse the two power wires based on that load. If thevehicle, running under load with the air conditioner, hea...

Page 9 - WIRING THE 4 PIN ALTERNATE IGNITION HARNESS

128-7405 9 of 28 GREEN Wire: Ignition 2 OutputConnect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when theignition key is turned to the "ON" or "RUN" position and is some cases the "START" or CRANK" position.This wire will sho...

Page 11 - Siren Wiring Detail; Positive Door Switch Wiring Detail

128-7405 11 of 28 Siren Wiring Detail 11 (-) TO VEHICLE'S CHASSIS GROUND TO WHITE w/BLACK WIRE OF MODULE Purple Wire: (+) Door Trigger InputIf the vehicle's door courtesy light switches + 12 volts when the door is opened, (Some Fords and someImports), you must connect this wire to the positive outpu...

Page 12 - General Motors VATS By-Pass Diagram

128-7405 12 of 28 A. Shock Sensor By Pass: If there is a Non Plug in Shock Sensor used with the alarm system and it is not shunted during theRemote Start activation period, then vibration from the running vehicle can cause the alarm to trigger. Inthis case, connect the Light Blue Wire to terminal #8...

Page 16 - Channel 3 Relay Wiring Detail

128-7405 16 of 28 Channel 3 Relay Wiring Detail 1 6 Green w/ Black Trace Wire: 300mA Latched Channel 4 OutputThe Green w/ Black Trace wire supplies a 300 mA switched output whenever channel four of the receiveris accessed. Pressing the pre-programmed transmitter button(s) will access channel four an...

Page 17 - some remote start trigger inputs, will damage the control module.; Green/Yellow Wire: DIESEL WAIT TO START INPUT; when the transmitter is used to alm/lock the system.; Black w/ Red Trace Wire: Pulsed Ground Output After Shutdown

128-7405 17 of 28 1 7 NOTE : This is a normally opened starter cut arrangement, when power is removed from thesecurity system, the starter disable feature will remain operational, and the vehicle will not start.Audiovox does not recommend using the Orange w/ White trace wire to interrupt anything bu...

Page 21 - change, the above sequence will have to be followed.

128-7405 21 of 28 2 1 NOTE: Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt Door Lock Control CircuitsThese applications require the use of additional components which may include relays, fixed resistors, orfor convenience, a Door Lock Interface. Refer to the A...

Page 22 - Programming Tach Rate:

128-7405 22 of 28 2 2 TEMPERATURE START:When Temperature Start, Bank 3 feature #13 is selected on, the temperature start mode can be activatedfrom the transmitter. See owners manual for turning this feature on from the transmitter. Once activated,the unit will start 1 time if the vehicle temperature...

Page 24 - the ignition switch off. DO NOT attempt to remove the key.

128-7405 24 of 28 If the unit fails this test, recheck your enable switch connection to the Ground and the Black/White wire ofthe Audiovox Remote Start Unit. If you have a plug in enable switch, check that the two pin connector isfirmly seated in the mating connector on the control module. DO NOT RE...

Page 27 - COMPLETING THE INSTALLATION:; these mechanisms and impair the safe operation of the vehicle.

128-7405 27 of 28 2 7 be connected to the hood pin switch. If the hood pin switch is also used for an alarm trigger input, becertain to use the dual diode assembly packaged with the Audiovox Remote Start Unit as shown in thisinstallation guide. (Page 9) AFTER THE CONNECTION OF THE NEUTRAL START SAFE...