Mitsubishi G-50A- Manuals

Mitsubishi G-50A– User Manual, Manual in PDF format online.

Manuals:

User Manual Mitsubishi G-50A

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11

Summary

Page 2 - Fig.1a System Configuration Example Using

1 The Procon MOD-IP/50 unit allows a Modbus building management system (BMS) to monitor and control air-conditioning units attached to aMitsubishi G-50A, GB-50A or AG-150 central controller (referred to as‘G-50’ from now on). The Modbus registers can be accessed via the serial comms interface using ...

Page 3 - Connection Details; Fig.2 Connection Details; IP addresses which must be on the same subnet.; Serial Comms Port; Fig.3a RS232 Comms Lead Wiring Diagram

3 2.1 Ethernet The Procon MOD-IP/50 is a 10Base-T half duplex device and needsto be connected to the G-50 and the local network (if Modbus/TCP isbeing used). Fig.1b shows the use of a hub / switch ( not supplied ) tomake the connections, but the Procon unit and the G-50 could just aseasily be connec...

Page 4 - THIS EQUIPMENT MUST BE EARTHED; link across the Enable Link terminals.; Fig.4 Grouping Example; Note: Attempting to write a command to a ‘slave’ unit will have no

5 2.3 Enable Link Allows a normally-closed volt-free contact to set or reset the ‘Forced-Off’ feature in the G-50. While the ‘Forced-Off’ feature is enabled, allair-conditioning units are switched off and all remote-controllers aredisabled. Upon detection of the open contact, the Procon unit sends t...

Manual Mitsubishi G-50A

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
65 Page 65
66 Page 66
67 Page 67
68 Page 68
69 Page 69

Summary

Page 2 - Introduction of Maintenance Tools; Foreword

1 1.1 Introduction of Maintenance Tools The Maintenance Tools are comprised of the On-Line Monitor and the Off-Line Monitor . The following two connection methods are available in the Online Monitoring. (1) Monitoring by connecting the maintenance tool to MN converter (CMS-MNF) via RS-232C. (2) Moni...

Page 5 - This manual refers to Windows; Available space 5 GB or more *2; *2 About Hard Disk Space

4 1.2 Required Operating Environment This manual refers to Windows ® 2000 as Windows 2000, and Windows ® XP as Windows XP. Trademarks MS, Microsoft, Microsoft logo, and Windows are registered trademarks and trade names of Microsoft Corporation. Each company may use as registered trademarks and trade...

Page 6 - There are two Maintenance Tool setup methods:; To set up Maintenance Tools, follow the 3 steps below.

5 1.3 Installation There are two Maintenance Tool setup methods: Method 1) New setup.(See Section 1.3.1) Method 2) Upgrading with existing setup.(See Section 1.3.2) 1.3.1 Setting Up the Maintenance Tools (New setup) To set up Maintenance Tools, follow the 3 steps below. Step 1) Setting up of MSDE St...

Mitsubishi Manuals