Mitsubishi Electric SE2U - Manuals

2 Important Safeguards 11. Power-cord protectionPower-supply cords should be routed so that they are not likely to be walked on orpinched by items placed upon or against them. Pay particular attention to cords atplugs, convenience receptacles, and points where they exit from the appliance. Do notput...

3 Important Safeguards WARNING: Unplug immediately if there is something wrong with your projector. Do not operate if smoke, strange noise or odor comes out of your projector. It may cause fireor electric shock. In this case, unplug immediately and contact your dealer. Never remove the cabinet. This...

4 Important Safeguards Place of installation For safety’s sake, do not use the projector at any place subjected to high temperature andhigh humidity. Please maintain an operating temperature, humidity, and altitude as specifiedbelow.• Operating temperature: between +41°F (+5°C) and +95°F (+35°C) • O...

5 Important Safeguards COMPLIANCE NOTICE OF FCC This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. ...

Introduction 6 Introduction Shipping Contents The projector is shipped with the cables required for connection to a PC and to video equip- ment. Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Projector...

Introduction 7 Projector Exterior View Front / Upper Side Rear Side Bottom Side Connector Panel Refer to page 11 for more information on making connections to various equipment. Projection lens Front adjuster foot Air inlet grill Front IR remote sensor Front adjuster button Focus ring and Zoom ring ...

Introduction 8 Controls and Functions External Control Panel 13 12 10 9 11 5 3 4 8 7 2 1 6 1. Power (Refer to pages 17 and 18 for more information.) Turns the projector on or off. 2. SOURCE (Refer to page 20 for more information.) Sequentially selects the input signal RGB/YP b P r , Video or S-Video...

Introduction 9 Remote Control Description POWER KEYSTONE AUTO Still MENU 6 Down MODE SOURCE MUTE PAGE UP / DOWN 3 Left / Right 4 5 Up Functions Descriptions Power Turns the projector on or off. Refer to pages 17 and 18 for more information. Still The image is frozen when Still is pressed. A “Pause” ...

Introduction 10 Remote Control Effective Range Infra Red (IR) remote control sensors are located on the front and the back of the projector. The remote control must be held at an angle within 30 degrees of the projector’s IR remote control sensors to function correctly. The distance between the remo...

Connection 11 Connection When connecting a signal source to the projector, be sure to: 1. Turn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. Connecting to a Laptop or Desktop Computer Important: A Mac adap...

Connection 12 Connecting Equipment to the Component Video Input The projector is capable of displaying various High Definition TV display modes. Some of these sources are: Most of these sources will provide an analog component video output, a standard VGA out- put, or a YP b P r format. The projecto...

Connection 13 Important: If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the video source is turned on and operating cor- rectly. Also check that the signal cables have been connected correctly. Connecting to Di...

Installation 14 Installation Choosing a Location Your projector is designed to be installed in the four installation configurations shown here: Floor front, Ceiling front, Floor rear, Ceiling rear. Your room layout or personal preference will dictate which installation configuration you use. For fur...

Installation 15 Adjusting the Height The projector is equipped with 1 quick-release adjuster foot and 2 rear adjuster feet. These adjusters change the image height and projection angle. To adjust the projector, 1. Lift the projector up and press the adjuster button to release the adjuster. The adjus...

Operation 17 Operation Start Up 1. Switch all of the connected equipment on. 2. Plug the power cord into the projector and into a wall socket. • The provided power cord 120V is rated at 120 V. Never connect this cord to any outlet or power supply using other voltages or frequencies than rated. If yo...

Operation 18 Shutdown 1. Press Power and a warn- ing message appears. Press Power a second time to turn the projector off. 2. The Power indicator light flashes orange and the lamp shuts down, the fans continue to run for approximately 110 sec-onds to cool down the pro-jector. To protect the lamp, th...

Operation 19 Digital Keystone Correction Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, you will need to man...

Operation 20 Source Selection To sequentially select input sources, press SOURCE on the projector control panel or the remote control. It may take you a few seconds when the projector is searching for input signals. The selected source will be displayed at the bottom right of the screen for 3 second...

Operation 21 Mute In order to draw the audience’s full attention to the presenter, you can use MUTE to hide the screen image and disable the audio. Press MUTE again to restore the image and audio. You can set the mute time in Advance --> Mute Time menu to restore the image and audio automatically...

Operation 23 Menu Operation Menu System Please note that the menus vary according to the signal type selected. Functions available when receiving different signal types... Sub-Menu PC Video / S-Video / Component Video Picture ModeKeystoneBrightnessContrast ModeKeystoneBrightnessContrastColorTint Pro...

Operation 24 Using the Menus The projector is equipped with on-screen display (OSD) menus for making various adjust- ments and settings. There are 8 different menu languages. (Refer to page 29 for more details.) The following example describes the adjustment of the keystone. 1. Press 6 MENU on the p...

Operation 25 1. Picture Menu PC signal input FUNCTION DESCRIPTION Mode Preset modes are provided so you can optimize your projector image set-up to suit your program type. 1. Presentation : Is designed for presentations. The brightness is emphasized in this mode. 2. Video : With a higher color tempe...

Operation 26 Video/ S-Video/ Component Video signal input FUNCTION DESCRIPTION Mode As described in the previous table. Keystone As described in the previous table. Brightness As described in the previous table. Contrast As described in the previous table. Color Increases or decreases the color inte...

Operation 28 3. Setting Menu *About color temperatures: There are many different shades that are considered to be “white” for various purposes. One of the common methods of representing white color is known as the “color temperature”. A white color with a low color temperature appears to be reddish ...

Operation 29 4. Advance Menu FUNCTION DESCRIPTION Mirror The projector can be installed on a ceiling or behind a screen, or with one or more mirrors. Contact your dealer for the ceiling mount bracket (optional accessory) if you need to install the projector on your ceiling. • Floor front: Select thi...

Operation 30 5. Information Menu This menu shows you the current operating status of the projector. PC signal input/ Component Video signal input Video/ S-Video signal input FUNCTION DESCRIPTION Source Shows the current signal source. Resolution Shows the native resolution of the input signal. Mode ...

Maintenance 31 Maintenance Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. • Use a canister of compressed air to remove dust. • If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner to gently wipe the lens surface. Important: ...

Maintenance 32 Lamp Information Warning Message When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may break. For m...

Maintenance 33 Replacing the Lamp • To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp. • To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp. • To reduce the risk ...

Maintenance 34 Step 5. Insert a new lamp. Make sure the handle is fully locked and tighten the screw firmly. Important: • Loose screw may cause a bad connection, which could result in malfunction.• Do not over tighten the screw.Step 6. Re-install the lamp cover and tighten the screw. Do not turn the...

Maintenance 35 Indicators Illustration 1. Blank - : Light OFF 2. : Light flashing 3. : Light ON 4. O : Orange light 5. R : Red light 6. G : Green light Light Status & Description Power Temp Lamp Power events - - (1) The projector needs 110 seconds to cool down as it was abnormally shut down with...

Maintenance 36 Light Status & Description Power Temp Lamp Lamp events - - (1) The projector needs 110 seconds to cool down. Or (2) Please contact your dealer for assistance. Thermal events - - The projector has shutdown automatically. If you try to re-start the projector, it will shutdown again....

Maintenance 37 Service Information Accessories (included in the standard package) Optional Accessories (not included in the standard package) Ordering Parts or Getting Information For product information, product assistance, service information, or to order accessories, please contact your dealer. D...

Troubleshooting 38 Troubleshooting THE PROJECTOR DOES NOT TURN ON. NO PICTURE BLURRED IMAGE REMOTE CONTROL DOES NOT WORK Cause Remedy There is no power from the power cable. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has...

Specifications 39 Specifications Projector Specifications Important: All specifications are subject to change without notice. General Product name DLP TM Projector Model name SE2U Optical Display Technology 0.55” Single chip Digital Micromirror Device (DMD) Lens F/Number F=2.6 to 3.1 Lamp 200W lamp ...

Specifications 40 Timing Chart Supported Timing for PC Input Supported Timing for Component Video-YP b P r Input Supported Timing for Video and S-Video Inputs • Some computers aren't compatible with the projector. • The projector's maximum resolution is 800 x 600 pixels. It may not display images of...

North AmericaMESCA (Mitsubishi Electric Sales Canada Inc.) http://www.mitsubishielectric.caInformation Technologies Group, 4299 14th Avenue, Markham, OntarioL3R 0J2, CanadaSales Phone :+1-(905) 475-7728 Fax :+1-(905) 475-7958 E-mail :[email protected] Technical Phone :+1-(905) 475-772...