Mazda 2008 B2300 Truck - Manuals

SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper to BumperCoverage, Safety Restraint Coverage and Corrosion Coverage. In addition,your vehicle is eligible for Emissions Defect and Emissions PerformanceWarranties. For a detailed description of what is covered and wha...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. WARNING: Please read the section Airbag supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructionscould result in ...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Manual Protecting theEnvironment Fasten Seat Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Flu...

Vehicle Symbol Glossary Power Windows Power Window Lockout Personal Alarm SystemFeature Engine Oil Engine Coolant Engine CoolantTemperature Do Not Open When Hot Battery Avoid Smoking, Flames,or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct FluidLevel MAX MIN Ser...

Headlamp control (pg. 42) Instrument panel dimmer control (pg. 43) Instrument cluster (pg. 12) Speed control* (pg. 57) Hood release (pg. 222) Driver air bag (pg. 86) Parking brake release (pg. 153) Turn signal and wiper/washer control (pg. 53) * If equipped 2008 B-Series (mbs) Owners Guide (post-200...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings or other vehicle components,possibly causing a fire. Check fuel cap: Illuminates when the fuel cap may not be properlyinstalled. Check the fuel fille...

Anti-lock brake system: If the ABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected; have the systemserviced immediately by yourauthorized dealer. Normal braking is still functional unless the brakewarning light also is illuminated. Airbag readiness: If this light fails t...

Engine coolant temperature: Illuminates when the engine coolanttemperature is high. Stop thevehicle as soon as possible , switch off the engine and let cool. Refer to Engine coolant in the Maintenance and Specifications chapter. WARNING: Never remove the coolant reservoir cap while theengine is runn...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...

AUDIO SYSTEMS AM/FM stereo (if equipped) WARNING: Driving while distracted can result in loss ofvehicle control, accident and injury. Mazda stronglyrecommends that drivers use extreme caution when using anydevice that may take their focus off the road. The driversprimary responsibility is the safe o...

5. TUNE : Press to manually go down/up ( / ) the radio frequency and also to selectvarious settings in menu mode. 6. SHUFF (Shuffle): Press to play the current CD/MP3 tracksin random order. In MP3directory mode, press to play the tracks within the current directoryin random order. 7. REPEAT: Press t...

1. AM/FM: Press to select AM/FM1/FM2 frequency bands. 2. CD: Press to enter CD/MP3 mode. If a CD/MP3 is already inthe system, the disc will startplaying. 3. AUX: Press to access AUX modes. To return to radio mode,press AM/FM. If equipped with SatelliteRadio, press AUX to cycle through SAT1, SAT2 SAT...

18. LOAD: Press to load a CD/MP3. To load a CD/MP3 disc to aspecific slot, press LOAD andselect the slot number by pressing the memory preset buttons. Pressand hold LOAD to autoload up to six discs. 19. CD slot: Insert a CD/MP3, label side up. Auxiliary input jack (Line in) Your vehicle may be equip...

6. Press AUX on the vehicle radio repeatedly until LINE IN appears in the display.You should hear audio from your portable music player although itmay be low. 7. Adjust the sound on your portable music player until it reaches the level of the FM station or CD by switching back and forth betweenthe A...

Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, theweaker the signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thundersto...

Do not use any irregular shapedCDs or discs with a scratchprotection film attached. CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker r...

• Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result in anaudio mute. Unlike AM/FM audible static, you will hear an audio mute when there isa satellite radio signal interference. Your radio display may display NOSIGNAL to i...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of aircirculated in the vehicle. 2. Temperature selection: Controls the temperature of theairflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief d...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Foglamp control (if equipped) The foglamps can be turned onwhen the headlamp control is inthe or position and the high beams are not turned on. Pull he...

Flash to pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position and • the headlamp control is in the OFF or parking lamp. WARNING: Always rememb...

switch from the full dim position to the full Dome/ON position to reset.This will ensure that your displays are visible under all lightingconditions. AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed before leaving theassembly plant. If your vehicle is involved in an accident or ...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. INTERIOR LAMPS Courtesy/reading lamps (if equipped) The courtesy lamp lights when: • any door is opened. • the instrument panel dimmerswitch is held up until thecourtesy lamps come on. • the ...

Function Number of bulbs Trade number Park/turn/side marker lamps (front) 2 3157 A (amber) Headlamps 2 9007 Fog lamps (if equipped) 2 9006 Hi-mount brake lamp 1 922 Rear stop/tail lamps 2 4157K or 3157K Rear turn lamps 2 3156 Rear license plate lamps 2 194 Backup lamps 2 3155 Dome lamp 1 912 Map/dom...

WARNING: Children and Halogen Bulbs: Playing with a halogenbulb is dangerous. Serious injuries could be caused by droppinga halogen bulb or breaking in some other way. Always keephalogen bulbs out of the reach of children. To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position,...

tabs in the lamp assembly. When the grooves are aligned, push thebulb into the lamp assembly until the plastic base contacts the rearof the lamp assembly. 2. Install the bulb retaining ring over the plastic base until it contacts the rear of the socket by rotating clockwise until you feel a “stop.” ...

Replacing fog lamp bulbs WARNING: Handling Halogen Bulbs: When a halogen bulbbreaks, it is dangerous. These bulbs contain pressurized gas. Ifone is broken, it will explode and serious injuries could becaused by the flying glass. If the glass portion of the bulb istouched with bare hands, body oil co...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers(from desired interval to low or highspeed position); rotate towards youto decrease the speed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single s...

Press and pull the window switchesto open and close windows. • Push down (to the first detent)and hold the switch to open. • Pull up and hold the switch toclose. One touch down Allows the driver’s window to openfully without holding the controldown. Push the switch completelydown to the second deten...

Fold-away mirrors Pull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash. SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a set speed without keepingyour foot on the accelerator pedal. WARNING: Do not use the speed control in heavy traff...

Reducing speed while using speed control There are three ways to reduce aset speed: • Press and hold the CST - controluntil you get to the desiredspeed, then release the control. • Press and release the CST -control to operate the Tap-Downfunction. Each tap will decrease the set speed by 1 mph (1.6 ...

KEYS The key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency. If your vehicle is equipped with the SecuriLock™ Passive Anti-theftsystem, your keys are coded to your vehicle; using a non-coded key willnot permit yo...

transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure. Note: Ensu...

The illuminated entry system will turn off the interior lights if: • the ignition switch is turned to the ON position, or • the remote transmitter lock control is pressed, or • after 25 seconds of illumination. The inside lights will not turn off if: • they have been turned on with the dimmer contro...

Vehicles equipped with the SecuriLock™ Passive Anti-theft systembehave as follows: • When the ignition is in the 1(OFF/LOCK) position, the indicator willflash once every 2 seconds for a total of 10 seconds to indicate theSecuriLock™ system is functioning as a theft deterrent. • When the ignition is ...

Pull lever located at the side of theseat cushion up to adjust seatback. 60/40 seat (if equipped) To gain access to the storagecompartment in your armrest (ifequipped), lift the latch to open lid. The 60/40 seat cupholder (ifequipped) is detachable forcleaning. • Firmly grasp the bottom of thecup ho...

To return seat to original position, slide the seat bottom back, then pushthe seatback up to lock it in place. The seat will lock, and you will haveto use the release bar to move the seat back to the original position. REAR SEATS Center facing jump seat (four–door Cab Plus 4) (if equipped) To open, ...

Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System™ totailor the deployment level of the driver dual-stage airbag based on seatposition. The system is designed to help protect smaller drivers sittingclose to the driver airbag by providing a lower airba...

If any of these things happen, even intermittently, have the PersonalSafety System™ serviced at an authorized dealer immediately. Unlessserviced, the system may not function properly in the event of acollision. Safety restraints precautions WARNING: Always drive and ride with your seatback uprightan...

WARNING: Each seating position in your vehicle has a specificseat belt assembly which is made up of one buckle and onetongue that are designed to be used as a pair. 1) Use theshoulder belt on the outside shoulder only. Never wear theshoulder belt under the arm. 2) Never swing the seat beltaround you...

movement. For example, if the driver brakes suddenly or turns a cornersharply, or the vehicle receives an impact of approximately 5 mph(8 km/h) or more, the combination seat belts will lock to help reduceforward movement of the driver and passengers. Automatic locking mode (outboard front passenger ...

How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic locking mode and activate thevehicle sensitive (emergency) locking mode. WARNING: After any vehicle collision, the entire seat beltsystem should be ch...

• Regular Cab and four–door CabPlus 4 To lower the shoulder belt height,push the button and slide the heightadjuster down. To raise the heightof the shoulder belt, slide the heightadjuster up. Pull down on the heightadjuster to make sure it is locked inplace. WARNING: Position the seat belt height a...

shoulder belt height adjusters (if equipped), shoulder belt guide onseatback (if equipped), child safety seat tether bracket assemblies (ifequipped), and attaching hardware, should be inspected after a collision.Mazda recommends that all seat belt assemblies used in vehicles involvedin a collision b...

If... Then... The driver’s or front passenger’sseat belt becomes unbuckled forapproximately 1 minute while thevehicle is traveling at least 3 mph(5 km/h) and more than 1-2minutes have elapsed since theignition switch has been turned toON... The Belt-Minder 威 feature is activated - the seat belt warn...

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The airbag supplemental restraint system is designed to work inconjunction with the seat belts to help protect the driver and frontoutboard passenger from certain upper body injuries. The term“supplemental restraint” means the airbags are intended as a supp...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

A difficulty with the system is indicated by one or more of the following: • The readiness lights will eitherflash or stay lit. • The readiness lights will notilluminate immediately afterignition is turned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the...

If it is necessary to modify an advanced front airbag system toaccommodate a person with disabilities, contact the Mazda CustomerRelationship Center at the phone number shown in the CustomerAssistance section of this Owner’s Manual. The front passenger sensing system may detect small or medium objec...

NOTE: Always follow the instructions and warnings that come with any infant or child restraint you might use. WARNING: Do not install a child seat in a center facing jumpseat. Children and seat belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for...

Child booster seats Children outgrow a typical convertible or toddler seat when they weigh40 pounds and are around 4 years of age. Although the lap/shoulder beltwill provide some protection, these children are still too small forlap/shoulder belts to fit properly, which could increase the risk of se...

Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has aremovable shield, remove theshield and use the lap/shoulderbelt. If a seating position has alow seat back and no headrestraint, a backless booster seatmay place...

Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the stomach, and lets you adjust the shoulder belt to cross thechest and rest snugly near the center of the shoulder. The drawingsbelow compare the ideal fit...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

7. Pull the lap belt portion across the child seat toward the buckleand pull up on the shoulder beltwhile pushing down with kneeon the child seat. 8. Allow the seat belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seatforward and back to mak...

The tether strap anchors in your vehicle are in the following positions(shown from top view): • Bucket seats • 60/40 seats WARNING: Attach the tether strap only to the appropriatetether anchor as shown. The tether strap may not workproperly if attached somewhere other than the correct tetheranchor. ...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary. Information on transfer case operation and shifting procedurescan be found in the Driving chapter. Information on transfer case maintenance can be f...

Treadwear The treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernment test course. For example, a tire graded 150 would wear oneand one-half (1 1/2) times as well on the government course as a tiregraded 100. The rela...

Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure of all tires and adjust ifrequired. At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflatea...

7. Check the sidewalls to make sure there are no gouges, cuts or bulges. TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that may be wedged in thetread grooves. Check for holes or cuts that may permit ...

WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressure, etc.) the tires experience throughout theirlives.In general, tires should be replaced after six years regardless oftread wear. However, heat caused...

It is recommended that the two front tires or two rear tires generally bereplaced as a pair. The tire pressure sensors mounted in the wheels (originally installed onyour vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Mazda MotorCorporation m...

Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your tires. If yourvehicle seems to pull to one side, vibrate or shake when you’re driving,the wheels may be out of alignment. Have a qualified technician...

4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match thenew wheel diameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You ...

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load can be carried by the tire. This pressure isnormally higher than the manufacturer’s recommended cold inflationpressure which can be found on the Saf...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation. WARNING: The Tire Pressure Monitoring System is NOT asubstitute for manually checking tire pressure. The t...

Low Tire PressureWarning Light Possible cause Customer Action Required Solid Warning Light Tire(s)under-inflated 1. Check your tire pressure toensure tires are properlyinflated; refer to Inflating your tires in this chapter. 2. After inflating your tires tothe manufacturer’srecommended inflationpres...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

any tire is under-inflated, carefully drive the vehicle to the nearestlocation where air can be added to the tires. Inflate all the tires to therecommended inflation pressure. SNOW TIRES AND CHAINS WARNING: Driving too fast for conditions creates the possibilityof loss of vehicle control. Driving at...

provide maximum return of vehicle design performance. Before loadingyour vehicle, familiarize yourself with the following terms for determiningyour vehicle’s weight ratings, with or without a trailer, from the vehicle’sTire Label or Safety Compliance Certification Label: Base Curb Weight – is the we...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s pla...

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not have enoughcargo capacity to carry that much weight. In metric units, thecalculation would be: 635 kg - (2 x 9...

Refer to the following chart for information regarding thefactory-equipped trailer tow connector: Trailer tow connector Color Function Comment 1. Dark Green Trailer right-handturn signal Circuit activated when brakepedal is depressed or whenignition is on and right-handturn signal is applied. 2. Yel...

• Anticipate stops and brake gradually. • Do not exceed the GCWR rating or transmission damage may occur. Servicing after towing If you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your scheduled maintenance information for more information. Tr...

• Place the transmission in N (Neutral). • Do not exceed a distance of 50 miles (80 km). • Do not exceed 35 mph (56 km/h) vehicle speed. • Put 4x4 switch in 2WD mode (4x4 only) • The vehicle must be towed in the forward position to ensure nodamage is done to the internal transfer case components. Fo...

When starting a fuel-injected engine, don’t press the accelerator beforeor during starting. Only use the accelerator when you have difficultystarting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter. WARNING: Extended idling at high engine speeds...

• steering wheel is turned when getting in or out of the vehicle Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine Note: Whenever you start your vehicle, release the key ...

• Be sure that areas where the vehicle is parked are clean and clear ofall combustibles such as petroleum products, dust, rags, paper andsimilar items. • Be sure that the engine block heater, heater cord and extension cordare solidly connected. A poor connection can cause the cord tobecome very hot ...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. (I...

rear brakes, the vehicle’s stopping distance will increase greatly and thehandling of your vehicle will be adversely affected. Pull the release lever to release thebrake. Driving with the parking brakeon will cause the brakes to wearout quickly and reduce fueleconomy. STEERING Your vehicle is equipp...

• Loose or worn suspension components TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under normal conditions, theTraction-Lok axle functions like a standard rear axle. The axle mayexhibit a slight nois...

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the ON position unless the brake pedal is depressed. If you cannot move the gearsh...

WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your authorized dealer. Driving with a 5–speed automatic transmission (if equipped) This vehicle is equipped with an adaptive Transmission Shift Strategy.Adaptiv...

Failure to fully depress the clutch pedal to the floor may causeincreased shift efforts, prematurely wear transmissioncomponents or damage the transmission. Do not drive with your foot resting on the clutch pedal or use theclutch pedal to hold your vehicle at a standstill while waiting on ahill. The...

3. Turn the ignition off. WARNING: Do not park your vehicle in Neutral, it may moveunexpectedly and injure someone. Use 1 (First) gear and setthe parking brake fully. Removing the key Turn the ignition off, push therelease lever (located above theignition), then turn the key towardyou and remove the...

4WD system indicator lights • 4x4 - Momentarily illuminates when the vehicle is started.Illuminates when 4H (4WD High)is engaged. • 4x4 LOW – Momentarily illuminates when the vehicle isstarted. Illuminates when 4L(4WD Low) is engaged. Using the electronic shift 4WD system 2H (2WD High) - Power to th...

2. On vehicles equipped with an automatic transmission, place the transmission in N (Neutral); on vehicles equipped with a manualtransmission, depress the clutch. 3. Move the 4WD control to the desired position. • If shifting into 4L (4WD Low), wait for the 4WD LOW light in theinstrument cluster to ...

When driving through water, determine the depth; avoid water higherthan the bottom of the hubs (if possible) and proceed slowly. If theignition system gets wet, the vehicle may stall. Once through water, always try the brakes. Wet brakes do not stop thevehicle as effectively as dry brakes. Drying ca...

Driving on snow and ice A 4WD vehicle has advantages over 2WD vehicles in snow and ice butcan skid like any other vehicle. Avoid sudden applications of power and quick changes of direction onsnow and ice. Apply the accelerator slowly and steadily when startingfrom a full stop. When braking, apply th...

HAZARD FLASHER CONTROL The hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is inany position or if the key is not inthe ignition. Push in the flasher control and allfront and rear direction signals willflash. Press the...

The fuel pump shut-off switch islocated on the right side of thepassenger footwell, behind the fusepanel door. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on thereset button. 4. Turn the ignition ON. 5...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 31 20A Front park lamps, Rear park lamps,License plate lamps, Dimmer switch,Trailer tow park lamps 32 5A Brake switch (logic), Brake-shiftinterlock 33 5A Instrument cluster battery feed (B+) 34 20A Power point 35 15A Po...

WARNING: Refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomesdamaged, it will no longer function. Dissimilar spare tire/wheel information WARNING: Failure to follow these guidelines could resul...

• Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability For vehicles equipped with 4WD, it is not recommended that the vehiclebe operated in 4WD modes with a temporary emergency spare tire. If4WD operation is necessary, do not ...

Stopping and securing the vehicle 1. Park on a level surface, activate hazard flashers and placegearshift lever in P (Park)(automatic transmission) or 1(First) (manual transmission). 2. Set the parking brake and turn engine OFF. Location of the spare tire and tools Note: The tire pressure monitoring...

When connecting the jack handle, assemble the following: • one handle extension and onetypical extension. To assemble,slide parts together. Todisconnect, depress button andpull apart. • one wheel nut wrench. Depressbutton and slide together. 2. If equipped, unlock and remove the spare tire carrier l...

3. Insert the square end of the jack handle into the rear accesshole located just above the rearbumper and below the tailgate. Forward motion will stop andresistance to turning will be feltwhen properly engaged. 4. Turn the handle counterclockwise until tire islowered to the ground and thecable is s...

Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1. Lay the tire on the ground with the valve stem facing up. 2. Slide the wheel partially under the vehicle and install the wire and retainer through the center o...

WARNING: When a wheel is installed, always remove anycorrosion, dirt or foreign materials present on the mountingsurfaces of the wheel or the surface of the wheel hub, brakedrum or brake disc that contacts the wheel. Ensure that anyfasteners that attach the rotor to the hub are secured so theydo not...

• If steam is coming from the engine compartment: do not go near the front of the vehicle. Stop the engine, then turn the ignition switchto the ON position without starting the engine. The radiator coolingfans will start to cool the engine. • If neither coolant nor steam is escaping: open the hood a...

transmission may have firm and/or soft shifts. This operation isconsidered normal and will not affect function or durability of thetransmission. Over time, the adaptive learning process will fully updatetransmission operation. 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect ...

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + – + – + – + – 2008 B-Series (mbs) Owners Guide (post-2002-fmt)USA (fus) Roadside Emergencies 191

4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery andthe fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. WARNING: Do not connect the end of the second c...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

CUSTOMER ASSISTANCE (U.S.A. MAINLAND AND HAWAII) Your complete and permanent satisfaction is our business. We are here toserve you. All Authorized Mazda Dealers have the knowledge and thetools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvementre...

4. Purchase date and current mileage 5. Your authorized dealer’s name and location 6. Your question(s) If you live outside the U.S.A., please contact your nearest MazdaDistributor. CUSTOMER ASSISTANCE (CANADA) Your complete and permanent satisfaction is our business. We are here toserve you. All Aut...

6. Your authorized dealer’s name and location 7. The nature of your problem and/or cause of dissatisfaction. The Department, in cooperation with the local Mazda ServiceRepresentative, will review the case to determine if everything possiblehas been done to ensure your satisfaction. Please recognize ...

CAMVAP is fully implemented in all provinces and territories. Consumerswishing to obtain further information about the Program can obtain aninformation booklet from their authorized dealer, the ProvincialAdministrator at 1 (800) 207-0685, or by contacting the Canadian MotorVehicle Arbitration Office...

IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor vehicle to conform to thevehicle’s applicable express warranty after a reasonable number ofattempts, the manufacturer shall be required to either replac...

• California Emission Control Warranty (if applicable) • Replacement Parts and Accessories Limited Warranty • Tire Warranty NOTE: Detailed warranty information is provided with your Mazda portfolio. Outside the United States Government regulations in the United States require that automobilesmeet sp...

WARNING: Add-On Electrical and Electronic Equipment:Incorrectly choosing or installing improper add-on equipment orchoosing an improper installer could be dangerous. Essentialsystems could be damaged, causing engine stalling, air-bag(SRS) activation, ABS inactivation, or a fire in the vehicle. Bever...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and spot paintedsurfaces. • Never wash a vehicle that is “hot to the touch” or dur...

• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND COVERS Aluminum wheel rims or covers are coated with a clearcoat paint finish.I...

• 4.0L Engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your dealer. • For routine cleaning, use cool or lukewarm...

a special solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade and windshield from automated carwash facilities. Be sure to replace wiper blades when they appearworn or do not function properly. • Do not use abrasives, as they may cause scratches. • Do not us...

INTRODUCTION Be extremely careful to prevent injury to yourself and others or damageto your vehicle when using this manual for inspection and maintenance. If you’re unsure about any procedure it describes, we strongly urge youto have a reliable and qualified service shop perform the work, preferably...

CHART SYMBOLS I : Inspect and if necessary, correct, clean or replace A Adjust R : Replace L : Lubricate Normal driving service intervals — perform at the months or distancesshown, whichever occurs first. Maintenance Item Maintenance Interval (Number of months or Miles (km), whichever comes first) M...

Maintenance Item Maintenance Interval (Number of months or Miles (km), whichever comes first) Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 miles 5 10 15 20 25 30 35 40 45 50 55 60 (x 1000 km) (8) (16) (24) (32) (40) (48) (56) (64) (72) (80) (88) (96) Disc brake system I I I I Caliper slide rails ...

*5 The California Air Resources Board has determined that the failure toperform this maintenance item will not nullify the emission warranty norlimit recall liability prior to completion of the vehicle’s useful life. Schedule 1 continued Maintenance Item Maintenance Interval (Number of months or Mil...

Special OperatingConditions Replace Engine Oil and Filter Inspect Brake System Replace Fuel Filter Change Automatic T ransmission Fluid Replace Spark Plugs Replace Engine Air Filter Change Manual T ransmission Fluid Inspect and Lubricate U-Joints Lubricate Front Wheel Bearing (4x2) Change T ransfer ...

• Check lap/shoulder belts and seat latches for wear and function. • Check air pressure in spare tire. • Check windshield washer spray and wiper operation. Clean wiperblades with clean cloth dampened with washer fluid. • Check safety warning lamps (brake, ABS, air bag, seat belt) foroperation. • Che...

2. Turn off the engine and remove the key. 3. Block the wheels. • Manual transmission/transaxle: 1. Set the parking brake, depress the clutch and place the gearshift in 1 (First). 2. Turn off the engine and remove the key. 3. Block the wheels. Working with the engine on • Automatic transmission: 1. ...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Windshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil dipstick 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil filler cap 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid ...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsMazda specification . Do not use anyspecial washer fluid such aswindshield water repellent type fluidor bug wash. They may causesqu...

Changing the wiper blades 1. Pull the wiper arm away from the vehicle. Turn the blade at anangle from the wiper arm. Pushthe lock pin manually to releasethe blade and pull the wiperblade down toward thewindshield to remove it fromthe arm. 2. Attach the new wiper to the wiper arm and press it intopla...

• 4.0L SOHC V6 engine 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is between the two holes or between the MIN and MAX marks (depending on application), the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the lower hole or the M...

7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity. Remove the ...

automobile manufacturers. Use an equivalent oil Mazda specification. SAE 5W-20 oil provides optimum fuel economy and durabilityperformance meeting all requirements for your vehicle’s engine . Change your engine oil and filter according to the appropriate schedulelisted in scheduled maintenance. Do n...

oil filters are designed for added engine protection and long life. If areplacement oil filter is used that does not meet Mazda Material anddesign specifications, start-up engine noises or knock may beexperienced. Mazda production and replacement oil filters are designed for addedengine protection a...

5. Turn the A/C on and allow the engine to idle for at least one minute. 6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more torelearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idl...

Adding engine coolant Use only Mazda Genuine Engine Coolant or a premium enginecoolant that meets a Mazda specification. • DO NOT USE Extended Life Engine Coolant (orange in color). • DO NOT USE a DEX-COOL 威 engine coolant or an equivalent engine coolant. • DO NOT USE alcohol or methanol antifreeze ...

For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when the engine is cool. Add the proper mixture of coolant andwater to the “FULL COLD” level. For all other vehicles, which have acoolant degas system wit...

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage. Recycled engine c...

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperature...

WARNING: Gasoline may contain benzene, which is acancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harmfulor fa...

WARNING: The flow of fuel through a fuel pump nozzle canproduce static electricity, which can cause a fire if fuel ispumped into an ungrounded fuel container. Use the following guidelines to avoid electrostatic charge build-up whenfilling an ungrounded fuel container: • Place approved fuel container...

Continuing to drive with the check fuel cap lamp or “check fuel cap” message on may cause the lamp to turn on as well. If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The warranty may be voidfor any damage to the fuel tank or fuel system i...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofgasolines labeled as “Regular” thatare sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes kno...

• Normally, adding 1 gallon (3.8L) of fuel is enough to restart theengine. If the vehicle is out of fuel and on a steep grade, more than 1gallon (3.8L) may be required. • The indicator may come on. For more information on the “check engine” or the “service engine soon” indicator, refer to Warning li...

• Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing thesame direction each time you fill up. • Have the vehicle loading and distribution the same every time. Your results w...

15 minutes of steady driving on an expressway/highway followed by 20minutes of stop-and-go driving with at least four 30-second idle periods. Allow the vehicle to sit for at least eight hours without starting theengine. Then, start the engine and complete the above driving cycle. Theengine must warm...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange the perfor...

TRANSMISSION FLUID Checking automatic transmission fluid • Refer to scheduled maintenance information for scheduled check and change intervals. • Transmission does not consume fluid. • Check fluid when transmission is not operating properly or if you seea leak. • Fluid level must be checked at norma...

Low fluid level Do not drive the vehicle if the fluidlevel is at or below the bottom ofthe dipstick. High fluid level Fluid levels above the safe rangemay cause overheating, shift and/orengagement concerns and internaltransmission damage. If an overfillcondition occurs, excess fluid shouldbe removed...

DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that requirelubrication. If the original universal joints are replaced with universaljoints equipped with grease fittings, lubrication will also be necessary. CHECKING AND ADDING REAR DIFFERENTIAL FLUID 1. Par...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross Vehicle Weight Rating (GVWR) /Restraint System 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence n...

CELL PHONES Use of cell phones and other devices by driver: WARNING: Use of any electrical devices such as cell phones,computers, portable radios, vehicle navigation or other devicesby the driver while the vehicle is moving is dangerous. Dialing anumber on a cell phone while driving also ties-up the...

A ABS (see Brakes) .....................151 Air cleaner filter ...............258, 260 Airbag supplemental restraintsystem ..........................................86 and child safety seats ..............89description ................................86disposal .........................................

lubricant specifications ..........260reverse .....................................160 Mirrors .........................................56 fold away ...................................57side view mirrors(power) ...............................56–57 Motorcraft parts ........................241 O Octan...