Makita MAC5200 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS

2 TABLE O F CONTENTS OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 TABLE OF CONTENTS SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warning Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 3 - SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS 3 OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS *** SAVE THESE INSTRUCTIONS *** WARNING IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT IN SERIOUS INJURY AND PROPERTY DAMAGE. READ AND UNDERSTAND ALL WARNINGS AND...

Page 4 - HAZARD

4 SAFETY INSTRUCTIONS OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 HAZARD WHAT CAN HAPPEN HOW TO PREVENT IT Risk of Air TankBursting. Risk of Attachmentsand AccessoriesBursting. The following conditions couldlead to a weakening of thetank, and RESULT IN A VIOLENT TANKEXPLOSION RESULTING INSERIO...

Page 7 - GLOSSARY

GLOSSARY - DUTY CYCLE - ON RECEIPT INSPECTION 7 OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 GLOSSARY DUTY CYCLE GENERAL INFORMATION ON RECEIPT INSPECTION CFM: Cubic feet per minute. SCFM: Standard cubic feet per minute; a unit of measure of air delivery. PSIG: Pounds per square inch gauge; a u...

Page 8 - STORAGE; Before you store the air compressor, make sure you do the following:; MOTOR THERMAL OVERLOAD PROTECTOR:; The electric motor has a manual thermal

8 STORAGE - DESCRIPTION OF OPERATION OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 ON RECEIPT INSPECTION ... Continued STORAGE DESCRIPTION OF OPERATION product was shipped directly to you, report any damages to the carrier and arrange forinspection of goods immediately. Before you store the air ...

Page 9 - INSTALLATION AND BREAK-IN PROCEDURES; PRESSURE SWITCH UNLOADING VALVE:; The pressure switch unloading valve located on; OUTLET PRESSURE GAUGE:; The tank pressure gauge indicates the air pressure in the tank.

INSTALLATION AND BREAK-IN PROCEDURES 9 OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 DESCRIPTION OF OPERATION ... Continued INSTALLATION AND BREAK-IN PROCEDURES PRESSURE SWITCH UNLOADING VALVE: The pressure switch unloading valve located on the side of the pressure switch, is designed to automat...

Page 10 - Initial Start Up Procedure:; MINIMUM; Plug power supply cord into correct power source.; Amp Rating

10 INSTALLATION AND BREAK-IN PROCEDURES OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 INSTALLATION AND BREAK-IN PROCEDURES ... Cont’d CAUTION: Multi-Viscosity motor oils, like 10W30, should not be used in an air compressor. They leave carbon deposits on critical components, thus reducing perform...

Page 11 - OPERATING PROCEDURES; Grounding Instruction:; DO NOT USE AN ADAPTER.

OPERATING PROCEDURES 11 OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 INSTALLATION AND BREAK-IN PROCEDURES ... Cont’d OPERATING PROCEDURES Piping: Plastic or PVC pipe is not designed for use with compressed air. Regardless of its indicatedpressure rating, plastic pipe can burst from air pressure...

Page 12 - MAINTENANCE; When you are finished:

12 MAINTENANCE OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 OPERATING PROCEDURES ... Continued MAINTENANCE When you are finished: Set the pressure switch lever to “OFF”. Using the air tool or accessory, bleed the tank pressure down to zero. Remove the air tool or accessory. Drain water from air...

Page 13 - ROUTINE MAINTENANCE SCHEDULE; Each year of operation or if a problem is suspected:

ROUTINE MAINTENANCE SCHEDULE 13 OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 ROUTINE MAINTENANCE SCHEDULE COLD WEATHER CONDITIONS Drain water from the air tank, any moisture separators or transformers. Check for any unusual noise and/or vibration. Manually check all safety valves to make sure t...

Page 14 - SERVICE INSTRUCTIONS; Units with External Brass Check Valve Replacement:

14 SERVICE INSTRUCTIONS OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 SERVICE INSTRUCTIONS Release all air pressure from air tank and unplug outfit. Remove shroud. Loosen the top and bottom nut of the outlet tube and remove. Remove the pressure release tube and fitting. Unscrew the check valve (...

Page 15 - TROUBLESHOOTING GUIDE; REPAIRS, UNPLUG THE COMPRESSOR AND BLEED OFF TANK AIR PRESSURE.; PROBLEM; Air leaks at fittings.; WARNING

TROUBLESHOOTING GUIDE 15 OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 TROUBLESHOOTING GUIDE PERFORMING REPAIRS MAY EXPOSE VOLTAGE SOURCES, MOVING PARTS OR COM- PRESSED AIR SOURCES. PERSONAL INJURY MAY OCCUR. PRIOR TO ATTEMPTING ANY REPAIRS, UNPLUG THE COMPRESSOR AND BLEED OFF TANK AIR PRESSURE....

Page 17 - Check valve is stuck open.

TROUBLESHOOTING GUIDE 17 OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 PROBLEM CAUSE CORRECTION Motor will not run. (con’t) Regulator knob has continuousair leak. Regulator will not shutoff at air outlet. Check valve is stuck open. Loose electrical connections. Possible defective capacitor. Pain...

Page 18 - RETAIN THIS PORTION FOR YOUR RECORDS

18 FACTORY SERVICE CENTERS OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 1-800-4-MAKITA - RETAIN THIS PORTION FOR YOUR RECORDS Arizona 3707 E. Broadway Road,Suite 6Phoenix, AZ 85040(602) 437-2850 California 41850 Christy StreetFremont, CA 94538-5107(510) 657-9881 14930 Northam StreetLa Mirada, C...

Page 19 - NOTES

WARNING - NOTES 19 OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activitiescontains chemicals known to the State of California to cause cancer, birth defects or otherreproductive harm. Some examples of...

Page 20 - MAKITA LIMITED ONE YEAR WARRANTY; Warranty Policy; This warranty does not apply where:; Makita Corporation

20 WARRANTY OWNERS MANUAL MAKITA - MAC700 / MAC2400 / MAC5200 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warrantedto be free of defects from workmanship and materials for the period of ONE YEAR from thedate ...

Page 21 - MAIL THIS PORTION; Your answers to the following questions are appreciated.

2) Use of this product is intended for: Construction TradeIndustrial MaintenanceHome MaintenanceHobbyOther 5) Any comments: AREA CODE: - TELEPHONE: SERIAL NO. MODEL NO. 1) This product was purchased from: Home CenterHardware/Lumber StoreTool DistributorIndustrial SupplyConstruction SupplyOther MAIL ...