Makita LS0714FL - Manuals - manualsarea.com

Page 2 - tandard equipment; Horizontal vise; ptional accessories; Set plate assembly

P 2 / 26 S tandard equipment T.C.T. Saw blade 190mm ............................... 1 pc Socket wrench 10 ........................................... 1 pc Dust bag ........................................................ 1 pc Vertical vise ................................................... 1 pc Hor...

Page 3 - epair; WARNING: Be sure to unplug the tool before maintenance or repair.

R epair P 3 / 2 6 Item No. Parts description Blade case Arm complete Front arm complete Apply 6g to the gear room if the room has been washed for cleaning.Both pivot portions where front arm (item No. 145) contacts Inside of hole which accepts arm holder's (156) rib portion.Linear ball bearing in wh...

Page 11 - Push compression spring in the direction

[11] Disassembling positive lock mechanism of turn base [12] Assembling positive lock mechanism of turn base Push compression spring in the direction designated with arrow (toward grip side). Fig. 11 Pin 3 Compression spring 6 Lock pin Fig. 10-1 Fig. 10-2 Tapping screw bind CT 4x16 Lock lever Lock l...

Page 12 - [13] Mounting stopper plate to arm holder; Insert this tail into the small hole; [15] Adjusting arm for smooth pivot action; Hex lock nut

[13] Mounting stopper plate to arm holder Mount stopper plate as illustrated in Fig. 12 . [14] Mounting ring 26 and set screw M4x8 1. Insert ring 26 into the hole of arm. See Fig. 13 . 2. Drive set screw M4x8 into the screw hole of arm by screwing thumb screw M6x33 with hex wrench. Stop driving the ...

Page 16 - Jig for laser line adjustment; (1) Mechanism for adjustment of the position of laser line

WARNING: Special attention should be taken to the adjustment because plugging the tool is required. Don't turn on the main switch for cutting operation of the tool while adjusting the laser line position. Turn on the switch of laser beam only. Never look into the laser beam. Direct laser beam may in...

Page 20 - Caution: Laserline label should be pasted again after adjustment.

10. Lower the jig again until it reaches the pan head screw M5x16 of link plate side. See Fig. 20-6. 11. Align the laser line with the line of jig by turning hex socket set screw M4x6 (A). See Fig. 20-9 . 12. Lift up the jig again until it reaches the pan head screw M5x16 of laser box side. See Fig....

Page 22 - iring diagram in Handle L; LS0714FL (with Fluorescent light and laser marker)

W iring diagram in Handle L Transformer Insulated connector Receptacles for connecting to laser switch Power supply cord Printed wiring board Rib C Rib BRib A Terminal block Motor housing Rib D Noise suppressor Main switch Pass the lead wires (black and red) of wiring board through the punched hole....

Page 23 - Brush

C ircuit diagram W iring diagram in handle L Color index of lead wires' sheath BlackWhiteRed OrangeBlue LS0714F (with Fluorescent light) LS0714F (with Fluorescent light) Brush holder A Brush holder B (1) (2) (5) (7) (8) (6) (3) (4) (1) Power supply cord (2) Main switch (5) Terminal block (6) Connect...

Page 25 - ircuit diagram; Color index of lead wires' sheath

C ircuit diagram Color index of lead wires' sheath BlackWhiteRed OrangeBlue LS0714L (with laser marker) Brush holder B Brush holder A (1) (2) (3) (4) (5) (8) (9) (10) (11) (12) (13) (6) Laser section Power source (1) Power supply cord (2) Main switch (3) Insulated connector (4) Noise suppressor (5) ...

Makita LS0714FL - Manuals

Manuals:

Manual Makita LS0714FL

Summary

Makita Manuals