Makita HRH01ZX2 - Manuals - manualsarea.com

Page 2 - ariation list; Note

P 2/2 2 V ariation list BHR262Z2CBHR262RD Model No. Type Quantity Battery adapter Battery converter Plastic carrying case Battery cover Yes Battery BHR262DP1 No No BHR262Z No 1 No No No No BAP36N BCV01 No No HR262DZ No No No No HR262DWB Yes 1 No HR262DWBE 2 BL3622A 1 DC36RA Charger No No No No No No...

Page 3 - epair; Transmission parts

[2] LUBRICATION [1] NECESSARY REPAIRING TOOLS R epair Description Code No. Use for Retaining ring S pliers ST-2N 1R003 Removing Ring spring 19 from Tool holder complete/ Tool holder guide complete Retaining ring S pliers ST-2 Bearing plate (for arbor press) 1R004 Removing Ring spring 29 1R022 or 1R3...

Page 4 - Cushion ring 13; Lubrication Around; Swash bearing section: 4g

Gear section: 17g Crank section: 5g boss for fixing Compression spring 14 [Inside view of Inner housing] [2] LUBRICATION (cont.) Apply Makita grease RB No.00 to the following portions indicated by black triangle to protect parts and product from unusual abrasion. Fig. 2 Fig. 3 BHR262 HR262D BHR262T ...

Page 9 - Viewed from the upper side

[3] DISASSEMBLY/ASSEMBLY [3]-3. Change lever While pushing Lock button into Change lever, turn Change lever a little over Drill mode position to lock it in place. While pushing Lock button into Change lever, fit Change lever completely to Gear housing complete. Note : Be sure to check Change lever w...

Page 13 - Tool holder guide section for BHR262T, HR262DT

[3] DISASSEMBLY/ASSEMBLY [3]-5. Tool holder section for BHR262, HR262D/ Tool holder guide section for BHR262T, HR262DT DISASSEMBLING Inner housing complete Flat washer 28 Piston cylinder Swash bearing section Take the disassembling step in reverse. Fig. 31 Fig. 32 Fig. 33 Note : Tool holder (guide) ...

Page 15 - Tool holder guide complete for BHR262T, HR262TD

[3] DISASSEMBLY/ASSEMBLY [3]-7. Impact bolt in Tool holder complete for BHR262, HR262D)/ Tool holder guide complete for BHR262T, HR262TD DISASSEMBLING (1) When Striker is left in Tool holder (guide) complete, push Striker out of Tool holder (guide) complete by inserting 1R281 from the top end then b...

Page 17 - Swash bearing portion; Piston cylinder portion

[3] DISASSEMBLY/ASSEMBLY [3]-8. Swash bearing 10, Gear section DISASSEMBLING Fig. 44 Note : This step can be done without removing Motor section. 1) Remove Gear housing complete as instructed in [3]-5 . 2) Remove Inner support complete by loosening two M4x25 Hex socket head bolts using 1R170. ( Fig....

Page 19 - Refer to

[4] Maintenance program It is recommended to replace the following parts at the same time when replacing Carbon brushes. ( Fig. 55 ) Note : Be sure to put Makita grease RB No. 00 and Molybdenum disulfide lubricant to the specific portions. Refer to Figs. 1, 2 and 3 . Fig. 55 BHR262/ HR262D BHR262T/ ...

Page 20 - ircuit diagram

Color index of lead wires' sheath Black Terminal LED Brush holder Switch M1 White Red Fig. D-1 Terminal LED Line filters Switch C ircuit diagram P 2 0 /2 2 With Equipment of Radio Interference Suppression Without Equipment of Radio Interference Suppression M2 T – T + T – T + M1 M2 Yellow Brush holde...

Page 21 - iring diagram; gray

W iring diagram Fig. D-2 To Brush holder complete Connector Connector ribs Diode Switch Lead wire holders FET (Field effect transistor) Lead wires must be tight in the area shown in gray . Fix lead wires in the Lead wire holders indicated by dotted circle . P 2 1 /2 2 inner wall of Housing Do not ro...

Makita HRH01ZX2 - Manuals

Manuals:

Manual Makita HRH01ZX2

Summary

Makita Manuals