Makita HM0860C - Manuals - manualsarea.com

Page 2 - SPECIFICATIONS; GENERAL SAFETY RULES; Read and understand all instructions.; Failure to follow all; SAVE THESE INSTRUCTIONS

2 SPECIFICATIONS • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in...

Page 4 - SPECIFIC SAFETY RULES

4 24. When servicing a tool, use only identicalreplacement parts. Follow instructions inthe Maintenance section of this manual. Use of unauthorized parts or failure to followMaintenance instructions may create a risk ofelectric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cor...

Page 7 - Indicator lamp; ASSEMBLY; Installing or removing the bit

7 Indicator lamp The green power-ON indicator lamp lights up when the tool isplugged. The indicator lamp is lit but the tool does not starteven if the tool is switched on, the carbon brushes may beworn out, or the electric circuit or the motor may be defective.If the indicator lamp does not light up...

Page 8 - Bit angle; OPERATION

8 Insert the bit into the tool. Turn the bit and push it in until itengages. If the bit cannot be pushed in, remove the bit. Pull the chuckcover down a couple of times. Then insert the bit again. Turnthe bit and push it in until it engages. After installing, always make sure that the bit is securely...

Page 9 - MAINTENANCE; Replacing carbon brushes

9 MAINTENANCE CAUTION: • Always be sure that the tool is switched off andunplugged before attempting to perform inspection ormaintenance. Replacing carbon brushes When the resin insulating tip inside the carbon brush isexposed to contact the commutator, it will automatically shutoff the motor. When ...

Page 10 - Lubrication

10 Lubrication This tool requires no hourly or daily lubrication because ithas a grease-packed lubrication system. It should be relubri-cated after every 6 months of operation. Send the completetool to Makita Authorized Service Center for this lubricationservice. However, if circumstances require th...

Page 11 - ACCESSORIES

11 Connect the terminal and reinstall the handle. CAUTION: • Be careful not to damage the terminal or lead wiresespecially when wiping out the old grease or installingthe handle. • Whenever reinstalling the handle, use the two shortscrews for the upper side and two long screws for thelower side. To ...

Page 12 - Memo

Page 14 - MAIL THIS PORTION; Your answers to the following questions are appreciated.; Please return this portion by facsimile or mail.

14 1. This product was purchased from: Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply Other ( ) 3. How did you learn about this product: Magazine From Dealer Newspaper Store Display Catalog Radio Exhibition From Friend Previous Usage Other ( ) 2. Use of the ...

Page 15 - FACTORY SERVICE CENTERS; RETAIN THIS PORTION FOR YOUR RECORDS

15 FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Avenue Sacrame...

Page 16 - WARNING; MAKITA LIMITED ONE YEAR WARRANTY; Warranty Policy; Makita Corporation

WARNING Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Californiato cause cancer, birth defects or other reproductive harm. Some examplesof these chemicals are:• lead from lead-based paints, • crystalline sili...

Makita HM0860C - Manuals

Manuals:

Manual Makita HM0860C

Summary

Makita Manuals