Makita G2800R - Manuals

CONTENTS 1. SAFETY PRECAUTIONS ・・・・・・・・・・・・・・・・・・・・・・ 1 2. SPECIFICATIONS ・・・・・・・・・・・・・・・・・・・・・・・・・・ 4 3. COMPONENTS ・・・・・・・・・・・・・・・・・・・・・・・・・・・ 5 4. PRE-OPERATION CHECKS ・・・・・・・・・・・・・・・・・・・・ 6 5. OPERATING PROCEDURES ・・・・・・・・・・・・・・・・・・・・ 11 6. WATTAGE INFORMATION ・・・・・・・・・・・・・・・・・・・・・ 24 7. SPARK A...

UPPER LEVEL LOWER LEVEL OIL FILLER NECK OIL GAUGE(OIL FILLER) UPPER LEVEL LOWER LEVEL 4. PRE-OPERATION CHECKS − 6 − CHECK ENGINE OIL. Before checking or refilling oil, be suregenerator is located on stable and levelsurface with engine stopped. ■ Remove oil filler cap and check theengine oil level. ■...

■ Check fuel level at fuel level gauge. ■ If fuel level is low, refill with unlead-ed automotive gasoline.This engine is certified to operateon automotive unleaded gasoline. ■ Be sure to use the fuel filter screenon the fuel filter neck. Fuel tank capacity : G2800R ・・・・・・ 3.17 US-gal. (12.0 liter) G...

CHECKING COMPONENT PARTS Check following items before starting engine: ■ Fuel leakage from fuel hose, etc. ■ Bolts and nuts for looseness. ■ Components for damage or breakage. ■ Generator not resting on or against any adjacent wiring. CHECK GENERATOR SURROUNDINGS. − 8 − Make sure you review each war...

− 9 − BATTERY INSTALLTION (Electric starter model) Recommended Battery: A capacity of 12V-24AH or larger. Death, personal injury and/or property damage may occur unless instruc-tions are followed carefully. ■ Use battery of recommended capacity. ■ Turn the starter switch to the "STOP" positi...

(a) Turn the engine switch to the position "ON". (Recoil starter model only) (b) Turn the no-fuse breaker to the "OFF" position. (c) Open the fuel cock. (d) Pull the choke knob to close if the engine is cold. 5. OPERATING PROCEDURES STARTING THE ENGINE − 11 − Check the oil level befo...

− 12 − ( f ) ［ Electric starter model ］ Insert the key into the key switch andturn it clockwise to the "RUN" positionto start the engine.Then turn the key further to the"START" position. The engine will bestarted by starting motor. RUN STOP STOP RUN START START OPEN ■ Do not run the ...

− 13 − USING ELECTRIC POWER ■ Make sure that the appliance is switched OFF before connecting it tothe generator. ■ Do not move the generator while it is running. ■ Be sure to ground the generator if the connected appliance isgrounded. Failure to ground unit may lead to electrical shock. WARNING CONT...

− 15 − (1) AC APPLICATION (a) Check the pilot lamp for proper voltage. ■ This generator is thoroughly tested andadjusted in the factory. If the generatordoes not produce the specified voltage,consult your nearest Makita factory or authorized service center. (b) Turn off the switch (es) of the electr...

− 16 − NOTE : When the no-fuse breaker turns off during operation, the generator is over loadedor the appliance is defective. Stop the generator immediately, check the applianceand / or generator for overloading or detect and have repaired as necessary by Makita factory or authorized service center....

− 17 − FULL POWER SWITCH Select the voltage using the FULLPOWER SWITCH in accordance with theelectrical appliance. Refer to TABLE 2 . 120V 120V 240V Change the FULL POWER SWITCHafter turning the no-fuse breaker to"OFF". ［ CAUTION ］ GFCI RECEPTACLE After starting the engine, check the GFCI fo...

− 18 − (2) CONNECTING TO DOMESTIC CIRCUITS (HOUSE WIRING) All Makita generators are a neutral grounded type.If a generator is to be connected to residential or commercial powerlines, such as a stand-by power source during power outage, all connec-tions must be made by a licensed electrician.Failure ...

− 21 − STOPPING THE GENERATOR (a) Turn off the power switch of the elec- tric equipment and unplug the cordfrom receptacle of the generator. (b) Turn the no-fuse breaker to the "OFF" position. (c) Allow the engine about 3 minutes to cool down at no-load before stopping. (d) ［ Recoil starter ...

6. WATTAGE INFORMATION − 23 − Some appliances need a "surge" of energy when starting. This means that the amount of electrical power needed to start the appliance may exceedthe amount needed to maintain its use.Electrical appliances and tools normally come with a label indicating voltage, cy...

− 24 − VOLTAGE DROP IN ELECTRIC EXTENSION CORDS When a long electric extension cord is used to connect an appliance or tool to thegenerator, a certain amount of voltage drop or loss occurs in the extension cordwhich reduces the effective voltage available for the appliance or tool. The use of improp...

7. SPARK ARRESTER − 25 − SPARK ARRESTER In a dry or wooded area, it is recommendable to use the product with a spark arrester. Some areas require the use of a spark arrester. Please check your local laws andregulations before operating your product. The spark arrester must be cleaned regularly to ke...

8. MAINTENANCE SCHEDULE − 26 − DAILY INSPECTION Before running the generator, check the following service items: Excessive vibration,noise Clean air cleaner element Safe surroundings Enough clean engine oil Leakage of gasoline and engine oil Loose or broken bolts and nuts Enough gasoline PERIODIC MA...

− 27 − *NOTE: 1. Initial oil change should be performed after first twenty (20) hours of operation. Thereafter change oil every hundred (100) hours. Before changing oil, check for a suitable way to dispose of old oil. Do not pour it down into sewage drains, onto garden soil or into openstreams. Your...

− 28 − 9. "HOW-TO" MAINTENANCE ENGINE OIL CHANGE ■ Change engine oil every 100 hours.(For new engine, change oil after 20hours.) (a) Drain oil by removing the drain plug and the oil filler cap while the engineis warm. (b) Reinstall the drain plug and fill the engine with oil until it reaches...

− 29 − COVER INNERELEMENT OUTERELEMENT 1. Urethane Foam Element Wash and clean the urethane foam with detergent. After cleaning, dry it.Clean the urethane foam element every 50 hours. 2. Paper element Clean by tapping gently to remove dirt and blow off dust.Never use oil. Clean the paper element eve...

− 30 − CLEANING FUEL STRAINER Dirt and water in the fuel are removed bythe fuel strainer. (a) Remove the strainer cup and throw away water and dirt. (b) Clean the screen and strainer cup with gasoline. (c) Tightly fasten the cup to main body, making sure to avoid fuel leak. FUEL HOSE REPLACEMENT Rep...

− 31 − 10. PREPARATION FOR STORAGE The following procedures should be followed prior to storage of your generator forperiods of 6 months or longer. ■ Drain fuel from fuel tank carefully by disconnecting the fuel line. Gasoline left in the fuel tank will eventually deteriorate making engine-startingd...

11. TROUBLESHOOTING − 32 − When generator engine fails to start after several attempts, or if no electricity isavailable at the output socket, check the following chart. If your generator still failsto start or generate electricity, contact your nearest Makita factory or authorized service center fo...

ISSUE EMD-GU2016 PRINTED IN JAPAN November 2004 CE-SK Makita Corporation 3-11-8, Sumiyoshi-choAnjo, Aichi 446-8502 Japan 3ZZ9020166 GENERATOR INSTRUCTIONS FOR USE アメリカ