Makita BTD150 - Manuals - manualsarea.com

Page 2 - SPECIFICATIONS; GENERAL SAFETY RULES; Read and understand all instructions.; Failure to follow all; SAVE THESE INSTRUCTIONS

2 SPECIFICATIONS • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA003-1 (FOR All BATTERY OPERATED TOOLS) WARNING: Read and understand all instructions. Failure to follow all instructions listed bel...

Page 4 - SPECIFIC SAFETY RULES

4 20. Use only accessories that are recom-mended by the manufacturer for yourmodel. Accessories that may be suitable for one tool may create a risk of injury whenused on another tool. SERVICE 21. Tool service must be performed only byqualified repair personnel. Service or main- tenance performed by ...

Page 5 - SYMBOLS

5 SYMBOLS USD302-1 The followings show the symbols used for tool. V ....................... volts ................... direct current ................... no load speed .../min ................ revolutions or reciprocation per minute ................ number of blow IMPORTANT SAFETY INSTRUCTIONS FOR CH...

Page 11 - ASSEMBLY

11 Switch action CAUTION: • Before inser ting the battery cartridge into the tool,always check to see that the switch trigger actuatesproperly and returns to the “OFF” position whenreleased. To star t the tool, simply pull the switch trigger. Tool speed isincreased by increasing pressure on the swit...

Page 12 - Installing or removing driver bit or socket bit; OPERATION; Screwdriving operation

12 Installing or removing driver bit or socket bit Use only the driver bit or socket bit shown in the figure. Donot use any other driver bit or socket bit. To install the bit, pull the sleeve in the direction of the arrowand insert the bit into the sleeve as far as it will go. Thenrelease the sleeve...

Page 13 - MAINTENANCE; Replacing carbon brushes

13 The proper fastening torque differs depending upon the kindor size of the screw/bolt, the material of the workpiece to befastened, etc. Refer to the figure for the relation between fas-tening time and wood screw size. (Material to be fastened:Lauan) NOTE: • Use the proper bit for the head of the ...

Page 14 - ACCESSORIES

14 Use a screwdriver to remove the brush holder caps. Take outthe worn carbon brushes, insert the new ones and securethe brush holder caps. After replacing brushes, insert the battery cartridge into thetool and break in brushes by running tool with no load forabout 1 minute. Then check the tool whil...

Page 15 - Memo

Page 18 - MAIL THIS PORTION; Your answers to the following questions are appreciated.; Please return this portion by facsimile or mail.

18 1. This product was purchased from: Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply Other ( ) 3. How did you learn about this product: Magazine From Dealer Newspaper Store Display Catalog Radio Exhibition From Friend Previous Usage Other ( ) 2. Use of the ...

Page 19 - FACTORY SERVICE CENTERS; RETAIN THIS PORTION FOR YOUR RECORDS

19 FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA 2365 Pelham ParkwayPelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211...

Page 20 - WARNING; MAKITA LIMITED ONE YEAR WARRANTY; Warranty Policy; Makita Corporation

WARNING Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Californiato cause cancer, birth defects or other reproductive harm. Some examplesof these chemicals are:• lead from lead-based paints, • crystalline sili...

Makita BTD150 - Manuals

Manuals:

Manual Makita BTD150

Summary

Makita Manuals