Page 2 - SPECIFICATIONS; GENERAL SAFETY RULES; Read and understand all instructions.; Failure to follow all; SAVE THESE INSTRUCTIONS
2 SPECIFICATIONS • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA003-1 (FOR All BATTERY OPERATED TOOLS) WARNING: Read and understand all instructions. Failure to follow all instructions listed bel...
Page 4 - SPECIFIC SAFETY RULES
4 18. Maintain tools with care. Keep cuttingtools sharp and clean. Properly maintained tools with sharp cutting edge are less likely tobind and are easier to control. 19. Check for misalignment or binding ofmoving parts, breakage of parts, and anyother condition that may affect the tool’soperation. ...
Page 5 - SYMBOLS
5 SYMBOLS USD302-1 The followings show the symbols used for tool. V ....................... volts ................... direct current ................... no load speed .../min ................ revolutions or reciprocation per minute ................ number of blow IMPORTANT SAFETY INSTRUCTIONS FOR CH...
Page 9 - ASSEMBLY
9 Switch action CAUTION: • Before inserting the battery cartridge into the tool,always check to see that the switch trigger actuatesproperly and returns to the “OFF” position whenreleased. To start the tool, simply pull the switch trigger. Tool speed isincreased by increasing pressure on the switch ...
Page 10 - Installing or removing driver bit or socket bit
10 Installing or removing driver bit or socket bit Use only the driver bit or socket bit shown in the figure. Donot use any other driver bit or socket bit. To install the bit, pull the sleeve in the direction of the arrowand insert the bit into the sleeve as far as it will go. Thenrelease the sleeve...
Page 11 - OPERATION
11 OPERATION The proper fastening torque may differ depending upon thekind or size of the screw/bolt, the material of the workpiece tobe fastened, etc. The relation between fastening torque andfastening time is shown in the figures. Hold the tool firmly and place the point of the driver bit in thesc...
Page 12 - MAINTENANCE; Replacing carbon brushes
12 4. The manner of holding the tool or the material of driving position to be fastened will affect the torque. 5. Operating the tool at low speed will cause a reduction in the fastening torque. MAINTENANCE CAUTION: • Always be sure that the tool is switched off and thebattery cartridge is removed b...
Page 13 - Recycling the Battery; ACCESSORIES
13 EN0001-1 Recycling the Battery The only way to dispose of a Makita battery is to recycle it.The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the tool. 2. a) Take the battery to your nearest Makita Factory Ser-vice Center or b) Take the battery to ...
Page 14 - Memo
Page 18 - MAIL THIS PORTION; Your answers to the following questions are appreciated.; Please return this portion by facsimile or mail.
18 1. This product was purchased from: Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply Other ( ) 3. How did you learn about this product: Magazine From Dealer Newspaper Store Display Catalog Radio Exhibition From Friend Previous Usage Other ( ) 2. Use of the ...
Page 19 - FACTORY SERVICE CENTERS; RETAIN THIS PORTION FOR YOUR RECORDS
19 FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA 2365 Pelham ParkwayPelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211...
Page 20 - WARNING; MAKITA LIMITED ONE YEAR WARRANTY; Warranty Policy; Makita Corporation
WARNING Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Californiato cause cancer, birth defects or other reproductive harm. Some examplesof these chemicals are:• lead from lead-based paints, • crystalline sili...