Page 2 - SPECIFICATIONS; GENERAL SAFETY RULES; Read and understand all instructions.; Failure to follow all; SAVE THESE INSTRUCTIONS
2 SPECIFICATIONS • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA003-1 (FOR All BATTERY OPERATED TOOLS) WARNING: Read and understand all instructions. Failure to follow all instructions listed bel...
Page 4 - SERVICE; SPECIFIC SAFETY RULES
4 19. Check for misalignment or binding of moving parts, breakage of parts, and anyother condition that may affect the tool’soperation. If damaged, have the tool ser-viced before using. Many accidents are caused by poorly maintained tools. 20. Use only accessories that are recom- mended by the manuf...
Page 5 - SYMBOLS
5 SYMBOLS USD302-1 The followings show the symbols used for tool. V ....................... volts ................... direct current ................... no load speed .../min ................ revolutions or reciprocation per minute ................ number of blow IMPORTANT SAFETY INSTRUCTIONS FOR CH...
Page 8 - Tips for maintaining maximum battery life
8 NOTE: • The battery charger is for charging Makita batterycartridge. Never use it for other purposes or for othermanufacturer’s batteries. • When you charge a new battery cartridge or a batterycartridge which has not been used for a long period oftime, it may not accept a full charge. This is a no...
Page 9 - ASSEMBLY; Selecting correct socket
9 Switch action CAUTION: • Before inserting the battery cartridge into the tool,always check to see that the switch trigger actuatesproperly and returns to the “OFF” position whenreleased. To start the tool, simply pull the switch trigger. Tool speed isincreased by increasing pressure on the switch ...
Page 10 - OPERATION
10 Installing or removing socket To install the socket, push it onto the anvil of the tool until itlocks into place.To remove the socket, simply pull it off. Installing set plate (optional accessory) Always install the set plate when using battery cartridges9100, 9102, 9101A. Install the set plate o...
Page 11 - MAINTENANCE; Replacing carbon brushes
11 • If the tool is operated continuously until the batterycartridge has discharged, allow the tool to rest for 15minutes before proceeding with a fresh battery. The fastening torque is affected by a wide variety of factorsincluding the following. After fastening, always check thetorque with a torqu...
Page 12 - Recycling the Battery; ACCESSORIES
12 Use a screwdriver to remove the brush holder caps. Take outthe worn carbon brushes, insert the new ones and securethe brush holder caps. After replacing brushes, insert the battery cartridge into thetool and break in brushes by running tool with no load forabout 1 minute. Then check the tool whil...
Page 14 - MAIL THIS PORTION; Your answers to the following questions are appreciated.; Please return this portion by facsimile or mail.
14 1. This product was purchased from: Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply Other ( ) 3. How did you learn about this product: Magazine From Dealer Newspaper Store Display Catalog Radio Exhibition From Friend Previous Usage Other ( ) 2. Use of the ...
Page 15 - FACTORY SERVICE CENTERS; RETAIN THIS PORTION FOR YOUR RECORDS
15 FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA 2365 Pelham ParkwayPelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211...
Page 16 - WARNING; MAKITA LIMITED ONE YEAR WARRANTY; Warranty Policy; Makita Corporation
WARNING Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Californiato cause cancer, birth defects or other reproductive harm. Some examplesof these chemicals are:• lead from lead-based paints, • crystalline sili...