Page 2 - SPECIFICATIONS; GENERAL SAFETY RULES; Read and understand all instructions.; Failure to follow all; SAVE THESE INSTRUCTIONS; Work Area
2 SPECIFICATIONS • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA003-1 (FOR All BATTERY OPERATED TOOLS) WARNING: Read and understand all instructions. Failure to follow all instructions listed bel...
Page 4 - SERVICE; SPECIFIC SAFETY RULES
4 viced before using. Many accidents are caused by poorly maintained tools. 20. Use only accessories that are recom- mended by the manufacturer for yourmodel. Accessories that may be suitable for one tool may create a risk of injury whenused on another tool. SERVICE 21. Tool service must be performe...
Page 5 - SYMBOLS
5 SYMBOLS USD302-1 The followings show the symbols used for tool. V ....................... volts ................... direct current ................... no load speed .../min ................ revolutions or reciprocation per minute ................ number of blow IMPORTANT SAFETY INSTRUCTIONS FOR CH...
Page 8 - Tips for maintaining maximum battery life
8 NOTE: • The battery charger is for charging Makita batterycartridge. Never use it for other purposes or for othermanufacturer’s batteries. • When you charge a new battery cartridge or a batterycartridge which has not been used for a long period oftime, it may not accept a full charge. This is a no...
Page 9 - ASSEMBLY; Selecting correct socket
9 Switch action CAUTION: • Before inserting the battery cartridge into the tool,always check to see that the switch trigger actuatesproperly and returns to the “OFF” position whenreleased. To start the tool, simply pull the switch trigger. Tool speed isincreased by increasing pressure on the switch ...
Page 10 - Installing or removing socket; OPERATION
10 Installing or removing socket To install the socket, push it onto the anvil of the tool until itlocks into place.To remove the socket, simply pull it off. OPERATION The proper fastening torque may differ depending upon thekind or size of the bolt, the material of the workpiece to befastened, etc....
Page 11 - MAINTENANCE; Recycling the Battery
11 • A worn socket ( wear on the hex end or square end )will cause a reduction in the fastening torque. 3. Bolt • Even though the torque coefficient and the class ofbolt are the same, the proper fastening torque willdiffer according to the diameter of bolt. • Even though the diameters of bolts are t...
Page 12 - ACCESSORIES
12 ACCESSORIES CAUTION: • These accessories or attachments are recommended foruse with your Makita tool specified in this manual. Theuse of any other accessories or attachments mightpresent a risk of injury to persons. Only use accessoryor attachment for its stated purpose. If you need any assistanc...
Page 14 - MAIL THIS PORTION; Your answers to the following questions are appreciated.; Please return this portion by facsimile or mail.
14 1. This product was purchased from: Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply Other ( ) 3. How did you learn about this product: Magazine From Dealer Newspaper Store Display Catalog Radio Exhibition From Friend Previous Usage Other ( ) 2. Use of the ...
Page 15 - FACTORY SERVICE CENTERS; RETAIN THIS PORTION FOR YOUR RECORDS
15 FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA 2365 Pelham ParkwayPelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211...
Page 16 - WARNING; MAKITA LIMITED ONE YEAR WARRANTY; Warranty Policy; Makita Corporation
WARNING Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Californiato cause cancer, birth defects or other reproductive harm. Some examplesof these chemicals are:• lead from lead-based paints, • crystalline sili...