Lucent Technologies Host-Based Controller Modem AT - Manuals

Page 2 - Lucent Technologies Inc.; AT Command Summary; Table 1. AT Command Set Summary

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 2 Version 1.0 Lucent Technologies Inc. AT Command Summary The following tables summarize the commands implemented by the modem. Commands may be executed whenthe modem is in COMMAND mode. COMMAND mode is entered upon under one of ...

Page 4 - Result Code

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998AT Command Summary (continued) Lucent Technologies Inc. Version 1.0 4 Table 4. The Result Code Summary Result Code Numeric Description OK 0 Command executed CONNECT 1 Modem connected to line RING 2 A ring signal has been detected ...

Page 5 - NoEC—No error control protocol.

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Command Summary (continued) Version 1.0 Lucent Technologies Inc. 5 Result Code Numeric Description CONNECT 29333 EC* 101 Connection at 29333 bit/s (V.90 mode) CONNECT 30666 EC* 102 Connection at 30666 bit/s (V.90 mode) CONNECT...

Page 6 - AT Commands Reference; Repeat Last Command

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 6 Version 1.0 Lucent Technologies Inc. AT Commands Reference AT commands are issued to the modem to control the modem's operation and software configuration. ATcommands can only be entered while the modem is in command mode. The ...

Page 7 - Dn

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 7 Dn Dial This command instructs the modem to begin the dialing sequence. The dial string (n, including modifiers and thetelephone number) is entered after the...

Page 8 - Hn

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Command Reference (continued) Lucent Technologies Inc. Version 1.0 8 OK n = 1 ERROR Otherwise Hn Hook Control This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy. H0: Mo...

Page 13 - Yn

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 13 Yn Long Space Disconnect Long space disconnect is always disabled. Y0: Disable long space disconnect (default). Y1: Enable long space disconnect (NOT SUPPOR...

Page 14 - DTR Control

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Command Reference (continued) Lucent Technologies Inc. Version 1.0 14 &Dn DTR Control This command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal. &D0: Ignore. The modem ...

Page 15 - Local Flow Control Selection

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 15 &Kn Local Flow Control Selection &K0: Disable flow control &K1: Reserved &K2: Reserved &K3: Enable RTS/CTS (hardware) flow control (defa...

Page 17 - View Active Configuration and Stored Profile

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 17 &V View Active Configuration and Stored Profile This command is used to display the active profiles. For example: Option Selection AT Cmd Comm Standard ...

Page 19 - Break Control; MNP* or disconnect mode. The modem attempts to connect using MNP 2

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 19 \J Bits/s Rate Adjusted This command determines whether or not the negotiated connect speed of the modem forces the adjustment ofthe speed of the DTE to the...

Page 21 - Inactivity Timer

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 21 \Tn Inactivity Timer This command specifies the length of time (in minutes) that the modem will wait before disconnecting when nodata is sent or received. A...

Page 22 - View Numbers in Blacklist

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Command Reference (continued) Lucent Technologies Inc. Version 1.0 22 The table below shows the possible values: “AT-V90=X” Downstream Rate 0 V.90 disabled 1 Auto Rate (default) 2 28000 kbit/s 3 29333 kbit/s 4 30666 kbit/s 5 3...

Page 23 - Data Compression Control

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 23 %Cn Data Compression Control This command determines the operation of V.42bis and MNP class 5 data compression. Online changes do nottake effect until a dis...

Page 24 - Test and Debug AT Commands; - external ram is good

Host-Based Modem Data Addendum AT Command Set June 15, 1998 24 Version 1.0 Lucent Technologies Inc. Test and Debug AT Commands The following commands are to be used for testing and debugging only and are not meant for general use. &&C Write to / Read from DSP Register AT&&C<loc>...

Page 25 - Table 1 - AT#UD Last Call Status Report Format; Key

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set Test and Debug AT Commands (continued) Version 1.0 Lucent Technologies Inc. 25 The modem may generate a single line or multiple lines, based on modem capabilities and call results, followedby a standard OK final result code. For ...

Page 26 - Table 2 - Call Setup Result Codes

Host-Based Modem Data Addendum AT Command Set June 15, 1998 Test and Debug AT Commands (continued) Lucent Technologies Inc. Version 1.0 26 41 3 digits 0-400 Error Control frame size 42 2 digits 0-FF Error control link timeouts X 43 2 digits 0-FF Error control link NAKs 44 Table 8 0-1 Compression Neg...

Page 28 - DteHangupCommand

Host-Based Modem Data Addendum AT Command Set June 15, 1998 Test and Debug AT Commands (continued) Lucent Technologies Inc. Version 1.0 28 2A CallAttemptsLimitExceeded X 2B ExtensionPhoneOffHook 2C CallSetupFailTimerExpired X 2D IncomingCallDetected X 2E LoopCurrentInterrupted 2F NoDialTone X 30 Voi...

Page 29 - AT Commands Reference S-Registers; Auto Answer Ring Number

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 29 Version 1.0 Lucent Technologies Inc. AT Commands Reference S-Registers S-registers generally affect how the AT commands perform. Contents of the registers can be displayed ormodified when the modem is in command mode.To displa...

Page 30 - Response Formatting Character (user defined)

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands Reference S-Registers (continued) Lucent Technologies Inc. Version 1.0 30 S4 Response Formatting Character (user defined) This register determines the ASCII value used as the line feed character. The modem uses a line...

Page 31 - Comma Dial Modifier Time; seconds; Automatic Disconnect Delay

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands Reference S-Registers (continued) Version 1.0 Lucent Technologies Inc. 31 S8 Comma Dial Modifier Time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dialcomman...

Page 32 - Results Bit Mapped Options Status

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands Reference S-Registers (continued) Lucent Technologies Inc. Version 1.0 32 S21 V.24/General Bit Mapped Options Status Indicates the status of command options. Only bits 3, 4 and 5 are used, read-only. Bits 3-4 DTR beha...

Page 33 - This register specifies a synthetic ring volume.; Synthetic Ring Frequency; auto rate

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands Reference S-Registers (continued) Version 1.0 Lucent Technologies Inc. 33 S30 Inactivity Timer S30 specifies the length of time (in minutes) that the modem will wait before disconnecting when no data is sentor receive...

Page 34 - K56flex Downstream Rate; Disable K56flex

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands Reference S-Registers (continued) Lucent Technologies Inc. Version 1.0 34 S38 K56flex Downstream Rate To force a particular K56flex downstream rate, use S-register S38. S38=0 disables K56flex, and may allow amore reli...

Page 35 - LAPM Error Control and Feature Negotiation (default 7); Negotiation enabled; Timer to Control Sleep Mode

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands Reference S-Registers (continued) Version 1.0 Lucent Technologies Inc. 35 S43 Auto Mode (default 1, range 0  1) This command is used for testing and debugging only.V.32bis startup auto mode operation disabled.0 = aut...

Page 36 - AT FAX Command Set; Table 5. The AT FAX Command Set Summary

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 36 Version 1.0 Lucent Technologies Inc. AT FAX Command Set (Class 1 FAX) The Lucent Technologies modem supports FAX commands conforming to EIA standard 578. These commandsare given here with short descriptions; complete explanati...

Page 37 - AT FAX Commands Reference; Service Class Indication; if in; Service Class Capabilities; This command causes the modem to display the classes it supports.; Service Class Selection; Select Facsimile Class 1.; Transmission Silence

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 37 Version 1.0 Lucent Technologies Inc. AT FAX Commands Reference +FCLASS? Service Class Indication This command causes the modem to display the current setting. The modem can operate either as a Class 0data modem or a class 1 FA...

Page 38 - Command Option

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Fax Commands Reference (continued) Lucent Technologies Inc. Version 1.0 38 +FTM=<m> Transmit FAX Data with <m> Carrier This command causes the modem to transmit data at the modulation specified by <m>. The fo...

Page 40 - This command sets the DTE to DCE fax port rate.

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Fax Commands Reference (continued) Lucent Technologies Inc. Version 1.0 40 +FPR=<n> Select Fax port rate This command sets the DTE to DCE fax port rate. DTE command DCE action Description or notes •FPR • 0 Execute •IPR •...

Page 41 - +FAA Adaptive answer; shall occur based on the calling device type.

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Fax Commands Reference (continued) Version 1.0 Lucent Technologies Inc. 41 +FAA Adaptive answer A Service Class 1 Facsimile DCE may have the ability to answer as a data modem DCE or as a Facsimile DCE. Italso may be able to ad...

Page 42 - AT Voice Command Set; Summary of the AT Voice Command Set

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 42 Version 1.0 Lucent Technologies Inc. AT Voice Command Set The AT Voice Command set follows a modified IS-101 architecture. The commands are sent through the commport, but the data path is sent either through the comm port or t...

Page 43 - AT Voice Commands Reference; Enter Voice Mode

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 43 Version 1.0 Lucent Technologies Inc. AT Voice Commands Reference AT+FCLASS=8 Enter Voice Mode The command AT+FCLASS=8 puts the modem in voice mode. Speakerphone and TAD modes are subsumedunder the more general heading of voice...

Page 44 - Receive Gain Selection

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Voice Commands Reference (continued) Lucent Technologies Inc. Version 1.0 44 AT+VGR=<gain> Receive Gain Selection This command will enable the receive microphone gain control. ✟ <gain> is 0  255: the only useful r...

Page 45 - AT Commands: Speakerphone Operation; Analog Source/Destination Selection; Attach internal speaker and internal microphone, DCE off-hook.; AT Commands: Telephone Answering Device; Beep Tone Duration Timer

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Voice Commands Reference (continued) Version 1.0 Lucent Technologies Inc. 45 AT Commands: Speakerphone Operation AT+VLS=<label> Analog Source/Destination Selection This is a general purpose analog source/destination comm...

Page 48 - AT Voice Command Set Not Defined In IS-101 Specifications; Synthetic Ring Volume; This does a flash hook.

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Voice Commands Reference (continued) Lucent Technologies Inc. Version 1.0 48 AT Voice Command Set Not Defined In IS-101 Specifications S32 Synthetic Ring Volume This command will provide a synthetic ring volume in dB with an i...

Page 49 - Voice Modem Command Examples; Notes for Speakerphone Examples

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Voice Commands Reference (continued) Version 1.0 Lucent Technologies Inc. 49 Voice Modem Command Examples The application issues AT commands to request actions by the modem, and the modem responds with standardTIA-602 result c...

Page 54 - Command

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Voice Commands Reference (continued) Lucent Technologies Inc. Version 1.0 54 AT+VSD=128,0 DTE selects normal silence detection sensitivity, and a silence detection intervalof 0 seconds. Disable silence detection. OK DCE respon...

Page 56 - AT DSVD Commands

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 56 Version 1.0 Lucent Technologies Inc. AT DSVD Commands In order to use the DSVD without a local phone, a ring 3 application can be used to simulate the local phone. Inthe absence of such an application, the voice connection nee...

Page 59 - Synchronous Access Mode AT commands; Initiate

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 59 Version 1.0 Lucent Technologies Inc. V.80 AT Commands The chip set supports the Synchronous Access Mode and most of the commands specified in V.80 standards.The commands are either AT commands issued in the command mode, or in...

Page 60 - Disable CRC

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 V.80 AT Commands (continued) Lucent Technologies Inc. Version 1.0 60 Table 10. V.80 AT Commands (continued) Command Sub- parameters Values Description +ESA=[<trans_idle>[,<framed_idle>[,,,<crc_type>[,<nrzi_en...

Page 61 - AT Commands for Homologation Testing and Debugging; Table 11. The Homologation Testing and Debugging Commands

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 61 Version 1.0 Lucent Technologies Inc. AT Commands for Homologation Testing and Debugging This section lists the homologation testing and debugging commands and homologation parameter values fordifferent countries. Table 11. The...

Page 62 - Name; V.21 Channel 2 mark symbol

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 62 Table 11. The Homologation Testing and Debugging Commands (continued) Name Description Value Comments %Txx V.22 1200 originate...

Page 63 - Configuring for Different Countries; Country

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 63 Configuring for Different Countries To configure for a specific country, execute the following AT commands: AT%T19,0,country_c...

Page 64 - Modifying Homologation Parameters

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 64 Modifying Homologation Parameters Once the modem is configured for a country, the homologation parameters shown in Table 3 can...

Page 65 - Homologation Parameters; Table 13. The Homologation Parameters

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 65 Homologation Parameters Table 13. The Homologation Parameters Par # Parameter Description Range Reference 1 Pulse dial make ti...

Page 66 - Parameter Description

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 66 Table 13. The Homologation Parameters (continued) Par # Parameter Description Range Reference 19 Number of failed attempts all...

Page 69 - Country Specific Homologation Parameters

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 69 Country Specific Homologation Parameters Country specific values for the homologation parameters are shown in Table 14.Note: T...

Page 81 - Canada

Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 81 Table 15. The Country Specific Homologation Parameters (continued) Par. # Canada Mexico India Vietnam Philippines 1 36 36 36 3...

Page 84 - Country Specific S Register Defaults

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 84 Country Specific S Register Defaults Note: The values listed in Table 15 are typical values and change based on OEM preference...

Page 86 - Changing the DTMF Dial Speed Default Value

Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 86 Changing the DTMF Dial Speed Default Value To change the DTMF dial speed default value, follow these steps:1. Set par# 5 (Min ...