Linear ak-11 - Manuals - manualsarea.com

Page 2 - MECHANICAL; FEATURES

CONTENTS INTRODUCTION Linear’s AK-11 is a digital keyless entry system designed foraccess control applications. The keypad is housed in a ruggedcast aluminum enclosure that can be mounted to a pedestal orbolted directly to a wall. The die-cast keys have bright,easy-to-read yellow graphics.Up to 480 ...

Page 3 - KEYLOCK; Figure 1. Component Locations; TYPICAL DOOR INSTALLATION WIRING; Figure 2. Wiring Diagram

COMPONENT LOCATIONS WIRING DIAGRAM TACTILEKEYPAD YELLOW"LOCKOUT"INDICATOR RED/GREENPOWER/ACCESSINDICATOR NIGHTLIGHT TERMINAL BLOCK J4POWER AND INPUTS KEYLOCK TERMINALBLOCK J3OUTPUTS JUMPER JP1REMOVE TOREDUCEBEEPER SOUND JUMPER JP2RESETSMASTER CODE Figure 1. Component Locations J4 1 2 3 4 5 6...

Page 4 - INSTALLATION; Pedestal Mounting; The AK-11 keypad can be mounted on a standard pedestal.; Wall Mounting; PEDESTAL; Figure 3. Pedestal Mounting Keypad Backplate; WALL MOUNTING; Figure 4. Wall Mounting Keypad Backplate

INSTALLATION To avoid damage to the unit from static discharges, connect theEARTH GROUND terminal to a good earth grounding point.Suggested wiring size is 18 AWG for earth ground and power (upto 500 feet of 18 AWG wire can be run for power, use larger wirefor longer runs). Use 22 AWG or larger (depe...

Page 5 - terminal. Connect a wire between the; Figure 5. Gate Installation

Gate Control Route four wires between the gate and the keypad (two forpower, two for control).Connect the gate operator’s auxiliary or radio power outputterminals to the keypads POWER input terminals (observewiring polarity).Connect the gate operator’s OPEN terminals to thekeypad’s Relay #1 COMMON &...

Page 6 - Master Code = the current 6-digit Master Programming Code; The red LED will light when Programming Mode is exited.; will

FACTORY DEFAULTS MASTER PROGRAMMING CODE . . . . . . . . . . . . . . . . . . . . 123456ENTRY CODE LENGTH . . . . . . . . . . . . . . . . . . . . . . . . . . 4 DIGITSREQUEST-TO-ENTER OUTPUT . . . . . . . . . . . . . . . . . . RELAY #1ALARM SHUNT OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 7 - PROGRAMMING OPTIONS; before; Sets the length of time Relay #1 activates when triggered.

PROGRAMMING OPTIONS Select Door Sense or Inhibit Input Default: Door Sense The input on terminal block J4, terminal #3 can be programmedfor DOOR SENSE or INHIBIT. Press: 1 0 # Input # Input = 1 for Inhibit, = 0 for Door Sense When programmed for DOOR SENSE, if an open condition onthe input occurs be...

Page 8 - THE MASTER PROGRAMMING CODE IS NOW 123456.

Beep Sounds on Keystrokes Default: Yes Selects whether or not the keypad beeps as each key is pressed. Press: 4 0 # Sound # Sound = 1 for Yes = 0 for No Beep Sounds During Relay #1 Default: No Selects whether or not the keypad beeps during Relay #1 activation. Press: 4 1 # Sound # Sound = 1 for Yes ...

Page 9 - The keypad’s beeper can be set to low or high level.; Locking Keypad; Figure 7. Using the Solid State Outputs

Solid State Outputs The two solid state outputs (Output #3 & Output #4) can beprogrammed to activate during various conditions. Theseoutputs can be used to activate indicators or sounders. SeeFigure 7 for wiring examples using the solid state outputs. Beeper Sound Level The keypad’s beeper can b...

Page 11 - MANAGER’S ENTRY CODE LOG; NAME

MANAGER’S ENTRY CODE LOG NAME ADDRESS OR APARTMENT NUMBER ENTRY CODE RELAY NUMBER ◊ 1 Timed ◊ 2 Timed ◊ 1 Toggled ◊ 2 Toggled ◊ 1 Timed ◊ 2 Timed ◊ 1 Toggled ◊ 2 Toggled ◊ 1 Timed ◊ 2 Timed ◊ 1 Toggled ◊ 2 Toggled ◊ 1 Timed ◊ 2 Timed ◊ 1 Toggled ◊ 2 Toggled ◊ 1 Timed ◊ 2 Timed ◊ 1 Toggled ◊ 2 Toggle...

LINEAR LIMITED WARRANTY This Linear product is warranted against defects in material andw o r k m a n s h i p f o r t w e n t y - f o u r ( 2 4 ) m o n t h s . T h e W ar r antyExpiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or ...